diff --git a/User_Setup.h b/User_Setup.h index d973c52..e0dfb75 100644 --- a/User_Setup.h +++ b/User_Setup.h @@ -27,7 +27,7 @@ // If STN32 Port A or B pins 0-7 are used for 8 bit parallel data bus bits 0-7 // then this will improve rendering performance by a factor of ~8x //#define STM_PORTA_DATA_BUS -//#define STM_PORTA_DATA_BUS +//#define STM_PORTB_DATA_BUS // Tell the library to use 8 bit parallel mode (otherwise SPI is assumed) //#define TFT_PARALLEL_8_BIT @@ -138,7 +138,7 @@ // // The TFT RESET pin can be connected to the NodeMCU RST pin or 3.3V to free up a control pin // -// The DC (Data Command) pin may be labeled AO or RS (Register Select) +// The DC (Data Command) pin may be labelled AO or RS (Register Select) // // With some displays such as the ILI9341 the TFT CS pin can be connected to GND if no more // SPI devices (e.g. an SD Card) are connected, in this case comment out the #define TFT_CS @@ -172,7 +172,7 @@ // Overlap mode shares the ESP8266 FLASH SPI bus with the TFT so has a performance impact // but saves pins for other functions. It is best not to connect MISO as some displays -// do not tristate that line wjen chip select is high! +// do not tristate that line when chip select is high! // On NodeMCU 1.0 SD0=MISO, SD1=MOSI, CLK=SCLK to connect to TFT in overlap mode // On NodeMCU V3 S0 =MISO, S1 =MOSI, S2 =SCLK // In ESP8266 overlap mode the following must be defined diff --git a/User_Setups/SetupX_Template.h b/User_Setups/SetupX_Template.h index 666c0e1..e0dfb75 100644 --- a/User_Setups/SetupX_Template.h +++ b/User_Setups/SetupX_Template.h @@ -27,7 +27,7 @@ // If STN32 Port A or B pins 0-7 are used for 8 bit parallel data bus bits 0-7 // then this will improve rendering performance by a factor of ~8x //#define STM_PORTA_DATA_BUS -//#define STM_PORTA_DATA_BUS +//#define STM_PORTB_DATA_BUS // Tell the library to use 8 bit parallel mode (otherwise SPI is assumed) //#define TFT_PARALLEL_8_BIT @@ -50,13 +50,17 @@ //#define R61581_DRIVER //#define RM68140_DRIVER //#define ST7796_DRIVER +//#define SSD1963_480_DRIVER +//#define SSD1963_800_DRIVER +//#define SSD1963_800ALT_DRIVER +//#define ILI9225_DRIVER //#define GC9A01_DRIVER // Some displays support SPI reads via the MISO pin, other displays have a single // bi-directional SDA pin and the library will try to read this via the MOSI line. // To use the SDA line for reading data from the TFT uncomment the following line: -// #define TFT_SDA_READ // This option is for ESP32 ONLY, tested with ST7789 display only +// #define TFT_SDA_READ // This option is for ESP32 ONLY, tested with ST7789 and GC9A01 display only // For ST7735, ST7789 and ILI9341 ONLY, define the colour order IF the blue and red are swapped on your display // Try ONE option at a time to find the correct colour order for your display @@ -68,7 +72,7 @@ // #define M5STACK -// For ST7789, ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation +// For ST7789, ST7735, ILI9163 and GC9A01 ONLY, define the pixel width and height in portrait orientation // #define TFT_WIDTH 80 // #define TFT_WIDTH 128 // #define TFT_WIDTH 240 // ST7789 240 x 240 and 240 x 320 @@ -76,6 +80,7 @@ // #define TFT_HEIGHT 128 // #define TFT_HEIGHT 240 // ST7789 240 x 240 // #define TFT_HEIGHT 320 // ST7789 240 x 320 +#define TFT_HEIGHT 240 // GC9A01 240 x 240 // For ST7735 ONLY, define the type of display, originally this was based on the // colour of the tab on the screen protector film but this is not always true, so try @@ -133,7 +138,7 @@ // // The TFT RESET pin can be connected to the NodeMCU RST pin or 3.3V to free up a control pin // -// The DC (Data Command) pin may be labeled AO or RS (Register Select) +// The DC (Data Command) pin may be labelled AO or RS (Register Select) // // With some displays such as the ILI9341 the TFT CS pin can be connected to GND if no more // SPI devices (e.g. an SD Card) are connected, in this case comment out the #define TFT_CS @@ -167,7 +172,7 @@ // Overlap mode shares the ESP8266 FLASH SPI bus with the TFT so has a performance impact // but saves pins for other functions. It is best not to connect MISO as some displays -// do not tristate that line wjen chip select is high! +// do not tristate that line when chip select is high! // On NodeMCU 1.0 SD0=MISO, SD1=MOSI, CLK=SCLK to connect to TFT in overlap mode // On NodeMCU V3 S0 =MISO, S1 =MOSI, S2 =SCLK // In ESP8266 overlap mode the following must be defined @@ -194,6 +199,16 @@ //#define TFT_RST 4 // Reset pin (could connect to RST pin) //#define TFT_RST -1 // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST +// For ESP32 Dev board (only tested with GC9A01 display) +// The hardware SPI can be mapped to any pins + +//#define TFT_MOSI 15 // In some display driver board, it might be written as "SDA" and so on. +//#define TFT_SCLK 14 +//#define TFT_CS 5 // Chip select control pin +//#define TFT_DC 27 // Data Command control pin +//#define TFT_RST 33 // Reset pin (could connect to Arduino RESET pin) +//#define TFT_BL 22 // LED back-light + //#define TOUCH_CS 21 // Chip select pin (T_CS) of touch screen //#define TFT_WR 22 // Write strobe for modified Raspberry Pi TFT only