diff --git a/Processors/pio_16bit_parallel.pio b/Processors/pio_16bit_parallel.pio
deleted file mode 100644
index bca2dc6..0000000
--- a/Processors/pio_16bit_parallel.pio
+++ /dev/null
@@ -1,76 +0,0 @@
-// Raspberry Pi Pico PIO program to output data to a TFT
-// controller via a 16 bit 8080 style data path.
-
-// Original sourced from:
-// https://github.com/zapta/pio_tft
-
-// Side set: 1 output pin, TFT_WR. Active low.
-// Data set: 16 consecutive output pins, TFT_D0 .. TFT_D15
-
-.program tft_io
-.side_set 1 opt ;  The TFT_WR output.
-
-// The C++ code switches between the different SM routines
-// by waiting for the SM to be idle and setting its PC.
-// The default SM routine is a 16 bit transfer
-
-// Do a block fill of N+1 pixels.
-public block_fill:
-   // Fetch colour value.
-   pull side 1
-   // Move colour to x.
-   mov x, osr
-   // Fetch pixel count N (sends N+1 pixels).
-   pull
-   // Move pixel count to y.
-   mov y, osr
-next:
-   // Copy colour value into osr, colour in LS 16 bits.
-   mov osr, x side 1
-   // Output colour 16 bits, unwanted top 16 bits shifted through.
-   out pins, 32 side 0 [1]
-   // Decrement pixel count and loop.
-   jmp y--, next side 1
-
-.wrap_target
-// Transmit an 8 bit value (LS 8 bits of 32 bits).
-public start_8:
-// Transmit a 16 bit value (LS 16 bits of 32 bits).
-public start_tx:
-   // Fetch the next 32 bit value from the TX FIFO and set TFT_WR high.
-   pull side 1
-   // Write the 16 bits and set WR low. This also
-   // shifts the unused top 16 bits through.
-   out pins, 32 side 0 [1]       
-   // Set WR high and jump back to start.
-   jmp start_tx side 1
-
-// Transmit a set window command sequence.
-public set_addr_window:
-   // Loop count in x (to send caset, paset and ramwr commands).
-   set x, 2 side 1
-pull_cmd:
-   // Set TFT_DC low.
-   set pins, 0
-   // Fetch caset, paset or ramwr.
-   pull
-   // Output LS byte (caset, paset or ramwr), discarding top 16 bits, set TFT_WR low.
-   out pins, 32 side 0
-   // Jump to end if 3rd cmd byte ramwr sent (x == 0)
-   jmp !x, end_set_addr
-   // pull next start and end coordinates, TFT_WR high.
-   pull side 1
-   // Set TFT_DC high.
-   set pins, 1
-send_xy:
-   // Output byte, TFT_WR low.
-   out pins, 8 side 0 [1]
-   // Loop until 4 bytes sent, TFT_WR high.
-   jmp !osre, send_xy side 1 [1]
-end_set_addr: // Jump here since delay needed before DC change
-   // Loop back for next command and write last command.
-   jmp x--, pull_cmd side 1
-   // Set DC high.
-   set pins, 1
-   // Auto-wrap back to start_tx.
-.wrap
\ No newline at end of file