Update for WROVER to address #232

The library supported 240x240 ST7789 displays only which require an 80
pixel offset in rotation 2 and 3
The library now also supports the 240x320 display which has a different
RGB colour order.

TFT_Drivers/ST7789_Defines.h

@@ -7,7 +7,9 @@
   #define TFT_HEIGHT 320
 #endif
 
-#define CGRAM_OFFSET
+#if (TFT_HEIGHT == 240) && (TFT_WIDTH == 240)
+  #define CGRAM_OFFSET
+#endif
 
 // Delay between some initialisation commands
 #define TFT_INIT_DELAY 0x80 // Not used unless commandlist invoked

TFT_Drivers/ST7789_Init.h

@@ -14,7 +14,12 @@
   //------------------------------display and color format setting--------------------------------//
   writecommand(ST7789_MADCTL);
   writedata(0x00);
-  writedata(0x48);
+#ifdef CGRAM_OFFSET
+  writedata(0x48); // BGR colour order for 240 x 240 TFT
+#else
+  writedata(0x40); // RGB colour order for 240 x 320 TFT (Issue #232)
+#endif
+
 
   // JLX240 display datasheet
   writecommand(0xB6);
@@ -114,7 +119,9 @@
 
   writecommand(ST7789_DISPON);    //Display on
 
+#ifdef TFT_BL
   // Turn on the back-light LED
   digitalWrite(TFT_BL, HIGH);
   pinMode(TFT_BL, OUTPUT);
+#endif
 }

TFT_Drivers/ST7789_Rotation.h

@@ -7,28 +7,36 @@
      writedata(TFT_MAD_RGB);
       _width  = _init_width;
       _height = _init_height;
+#ifdef CGRAM_OFFSET
        colstart = 0;
        rowstart = 0;
+#endif
      break;
    case 1: // Landscape (Portrait + 90)
      writedata(TFT_MAD_MX | TFT_MAD_MV | TFT_MAD_RGB);
       _width  = _init_height;
       _height = _init_width;
-       colstart = 0;
+#ifdef CGRAM_OFFSET
-       rowstart = 0;
+      colstart = 0;
-     break;
+      rowstart = 0;
+#endif
+       break;
    case 2: // Inverter portrait
      writedata(TFT_MAD_MX | TFT_MAD_MY | TFT_MAD_RGB);
       _width  = _init_width;
       _height = _init_height;
-       colstart = 0;
+#ifdef CGRAM_OFFSET
-       rowstart = 80;
+      colstart = 0;
-     break;
+      rowstart = 80;
+#endif
+       break;
    case 3: // Inverted landscape
      writedata(TFT_MAD_MV | TFT_MAD_MY | TFT_MAD_RGB);
       _width  = _init_height;
       _height = _init_width;
-       colstart = 80;
+#ifdef CGRAM_OFFSET
-       rowstart = 0;
+      colstart = 80;
-     break;
+      rowstart = 0;
+#endif
+       break;
   }

User_Setup.h

@@ -24,16 +24,19 @@
 //#define ILI9481_DRIVER
 //#define ILI9486_DRIVER
 //#define ILI9488_DRIVER
-//#define ST7789_DRIVER
+//#define ST7789_DRIVER // Define the screen size below for this display
 
 // For M5Stack ESP32 module with integrated display ONLY, remove // in line below
 //#define M5STACK
 
-// For ST7735  and ILI9163 ONLY, define the pixel width and height in portrait orientation
+// For ST7789, ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
 // #define TFT_WIDTH  80
 // #define TFT_WIDTH  128
+// #define TFT_WIDTH  240 // ST7789 240 x 240 and 240 x 320
 // #define TFT_HEIGHT 160
-//#define TFT_HEIGHT 128
+// #define TFT_HEIGHT 128
+// #define TFT_HEIGHT 240 // ST7789 240 x 240
+// #define TFT_HEIGHT 320 // ST7789 240 x 320
 
 // For ST7735 ONLY, define the type of display, originally this was based on the
 // colour of the tab on the screen protector film but this is not always true, so try
@@ -46,10 +49,10 @@
 // #define ST7735_GREENTAB
 // #define ST7735_GREENTAB2
 // #define ST7735_GREENTAB3
-// #define ST7735_GREENTAB128 // For 128 x 128 display
+// #define ST7735_GREENTAB128    // For 128 x 128 display
 // #define ST7735_GREENTAB160x80 // For 160 x 80 display (BGR, inverted, 26 offset)
 // #define ST7735_REDTAB
-//#define ST7735_BLACKTAB
+// #define ST7735_BLACKTAB
 
 // ##################################################################################
 //
@@ -94,7 +97,9 @@
 #define TFT_CS   PIN_D8  // Chip select control pin D8
 #define TFT_DC   PIN_D3  // Data Command control pin
 #define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
-//#define TFT_RST  -1  // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+//#define TFT_RST  -1    // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+
+//#define TFT_BL PIN_D1  // LED back-light (only for ST7789 with backlight control pin)
 
 //#define TOUCH_CS PIN_D2     // Chip select pin (T_CS) of touch screen
 
@@ -124,10 +129,12 @@
 //#define TFT_MISO 19
 //#define TFT_MOSI 23
 //#define TFT_SCLK 18
-//#define TFT_CS    15  // Chip select control pin
+//#define TFT_CS   15  // Chip select control pin
 //#define TFT_DC    2  // Data Command control pin
 //#define TFT_RST   4  // Reset pin (could connect to RST pin)
 //#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+//#define TFT_BL   32  // LED back-light (only for ST7789 with backlight control pin)
+
 
 // For the M5Stack module use these #define lines
 //#define TFT_MISO 19
@@ -136,7 +143,7 @@
 //#define TFT_CS   14  // Chip select control pin
 //#define TFT_DC   27  // Data Command control pin
 //#define TFT_RST  33  // Reset pin (could connect to Arduino RESET pin)
-//#define TFT_BL   32  // LED back-light
+//#define TFT_BL   32  // LED back-light (required for M5Stack)
 
 //#define TOUCH_CS 21     // Chip select pin (T_CS) of touch screen
 

User_Setups/SetupX_Template.h

@@ -6,6 +6,7 @@
 //
 //   If this file is edited correctly then all the library example sketches should
 //   run without the need to make any more changes for a particular hardware setup!
+//   Note that some sketches are designed for a particular TFT pixel width/height
 
 // ##################################################################################
 //
@@ -19,15 +20,23 @@
 //#define ILI9163_DRIVER
 //#define S6D02A1_DRIVER
 //#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
+//#define HX8357D_DRIVER
+//#define ILI9481_DRIVER
+//#define ILI9486_DRIVER
+//#define ILI9488_DRIVER
+//#define ST7789_DRIVER // Define the screen size below for this display
 
 // For M5Stack ESP32 module with integrated display ONLY, remove // in line below
 //#define M5STACK
 
-// For ST7735  and ILI9163 ONLY, define the pixel width and height in portrait orientation
+// For ST7789, ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
-//#define TFT_WIDTH  80
+// #define TFT_WIDTH  80
-//#define TFT_WIDTH  128
+// #define TFT_WIDTH  128
-//#define TFT_HEIGHT 160
+// #define TFT_WIDTH  240 // ST7789 240 x 240 and 240 x 320
-//#define TFT_HEIGHT 128
+// #define TFT_HEIGHT 160
+// #define TFT_HEIGHT 128
+// #define TFT_HEIGHT 240 // ST7789 240 x 240
+// #define TFT_HEIGHT 320 // ST7789 240 x 320
 
 // For ST7735 ONLY, define the type of display, originally this was based on the
 // colour of the tab on the screen protector film but this is not always true, so try
@@ -36,14 +45,14 @@
 // Comment out ALL BUT ONE of these options for a ST7735 display driver, save this
 // this User_Setup file, then rebuild and upload the sketch to the board again:
 
-//#define ST7735_INITB
+// #define ST7735_INITB
-//#define ST7735_GREENTAB
+// #define ST7735_GREENTAB
-//#define ST7735_GREENTAB2
+// #define ST7735_GREENTAB2
-//#define ST7735_GREENTAB3
+// #define ST7735_GREENTAB3
-//#define ST7735_GREENTAB128 // For 128 x 128 display
+// #define ST7735_GREENTAB128    // For 128 x 128 display
-//#define ST7735_GREENTAB160x80 // For 160 x 80 display (BGR, inverted, 26 offset)
+// #define ST7735_GREENTAB160x80 // For 160 x 80 display (BGR, inverted, 26 offset)
-//#define ST7735_REDTAB
+// #define ST7735_REDTAB
-//#define ST7735_BLACKTAB
+// #define ST7735_BLACKTAB
 
 // ##################################################################################
 //
@@ -88,9 +97,11 @@
 #define TFT_CS   PIN_D8  // Chip select control pin D8
 #define TFT_DC   PIN_D3  // Data Command control pin
 #define TFT_RST  PIN_D4  // Reset pin (could connect to NodeMCU RST, see next line)
-//#define TFT_RST  -1  // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
+//#define TFT_RST  -1    // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
 
-//#define TOUCH_CS PIN_D1     // Chip select pin (T_CS) of touch screen
+//#define TFT_BL PIN_D1  // LED back-light (only for ST7789 with backlight control pin)
+
+//#define TOUCH_CS PIN_D2     // Chip select pin (T_CS) of touch screen
 
 //#define TFT_WR PIN_D2       // Write strobe for modified Raspberry Pi TFT only
 
@@ -118,14 +129,12 @@
 //#define TFT_MISO 19
 //#define TFT_MOSI 23
 //#define TFT_SCLK 18
-//#define TFT_CS    15  // Chip select control pin
+//#define TFT_CS   15  // Chip select control pin
 //#define TFT_DC    2  // Data Command control pin
 //#define TFT_RST   4  // Reset pin (could connect to RST pin)
 //#define TFT_RST  -1  // Set TFT_RST to -1 if display RESET is connected to ESP32 board RST
+//#define TFT_BL   32  // LED back-light (only for ST7789 with backlight control pin)
 
-//#define TOUCH_CS 22     // Chip select pin (T_CS) of touch screen
-
-//#define TFT_WR 21    // Write strobe for modified Raspberry Pi TFT only
 
 // For the M5Stack module use these #define lines
 //#define TFT_MISO 19
@@ -134,8 +143,40 @@
 //#define TFT_CS   14  // Chip select control pin
 //#define TFT_DC   27  // Data Command control pin
 //#define TFT_RST  33  // Reset pin (could connect to Arduino RESET pin)
-//#define TFT_BL   32  // LED back-light
+//#define TFT_BL   32  // LED back-light (required for M5Stack)
 
+//#define TOUCH_CS 21     // Chip select pin (T_CS) of touch screen
+
+//#define TFT_WR 22    // Write strobe for modified Raspberry Pi TFT only
+
+// ######       EDIT THE PINs BELOW TO SUIT YOUR ESP32 PARALLEL TFT SETUP        ######
+
+// The library supports 8 bit parallel TFTs with the ESP32, the pin
+// selection below is compatible with ESP32 boards in UNO format.
+// Wemos D32 boards need to be modified, see diagram in Tools folder.
+// Only ILI9481 and ILI9341 based displays have been tested!
+
+// Parallel bus is only supported on ESP32
+// Uncomment line below to use ESP32 Parallel interface instead of SPI
+
+//#define ESP32_PARALLEL
+
+// The ESP32 and TFT the pins used for testing are:
+//#define TFT_CS   33  // Chip select control pin (library pulls permanently low
+//#define TFT_DC   15  // Data Command control pin - use a pin in the range 0-31
+//#define TFT_RST  32  // Reset pin, toggles on startup
+
+//#define TFT_WR    4  // Write strobe control pin - use a pin in the range 0-31
+//#define TFT_RD    2  // Read strobe control pin  - use a pin in the range 0-31
+
+//#define TFT_D0   12  // Must use pins in the range 0-31 for the data bus
+//#define TFT_D1   13  // so a single register write sets/clears all bits.
+//#define TFT_D2   26  // Pins can be randomly assigned, this does not affect
+//#define TFT_D3   25  // TFT screen update performance.
+//#define TFT_D4   17
+//#define TFT_D5   16
+//#define TFT_D6   27
+//#define TFT_D7   14
 
 // ##################################################################################
 //
@@ -167,9 +208,9 @@
 #define LOAD_FONT2  // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
 #define LOAD_FONT4  // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
 #define LOAD_FONT6  // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
-#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:.
+#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
-//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
 #define LOAD_FONT8  // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
+//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
 #define LOAD_GFXFF  // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
 
 // Comment out the #define below to stop the SPIFFS filing system and smooth font code being loaded
@@ -202,9 +243,11 @@
 // #define SPI_FREQUENCY  20000000
 #define SPI_FREQUENCY  27000000 // Actually sets it to 26.67MHz = 80/3
 // #define SPI_FREQUENCY  40000000 // Maximum to use SPIFFS
-// #define SPI_FREQUENCY  53400000
 // #define SPI_FREQUENCY  80000000
 
+// Optional reduced SPI frequency for reading TFT
+#define SPI_READ_FREQUENCY  20000000
+
 // The XPT2046 requires a lower SPI clock rate of 2.5MHz so we define that here:
 #define SPI_TOUCH_FREQUENCY  2500000
 
@@ -219,4 +262,4 @@
 // Transactions are automatically enabled by the library for an ESP32 (to use HAL mutex)
 // so changing it here has no effect
 
-// #define SUPPORT_TRANSACTIONS
+//#define SUPPORT_TRANSACTIONS

library.json

@@ -1,6 +1,6 @@
 {
   "name": "TFT_eSPI",
-  "version": "1.1.2",
+  "version": "1.1.3",
   "keywords": "tft, ePaper, display, ESP8266, NodeMCU, ESP32, M5Stack, ILI9341, ST7735, ILI9163, S6D02A1, ILI9486, ST7789",
   "description": "A TFT and ePaper SPI graphics library for ESP8266 and ESP32",
   "repository":

library.properties

@@ -1,5 +1,5 @@
 name=TFT_eSPI
-version=1.1.2
+version=1.1.3
 author=Bodmer
 maintainer=Bodmer
 sentence=A fast TFT graphics library for ESP8266 and ESP32 processors for the Arduino IDE