Fix #1760, fix #1763, fix #1764

Processors/TFT_eSPI_RP2040.h

@@ -22,6 +22,11 @@
 // Processor ID reported by getSetup()
 #define PROCESSOR_ID 0x2040
 
+// Transactions always supported
+#ifndef SUPPORT_TRANSACTIONS
+  #define SUPPORT_TRANSACTIONS
+#endif
+
 // Include processor specific header
 // None
 
@@ -285,6 +290,25 @@
         spi.transfer(0); spi.transfer((C)>>8); \
         spi.transfer(0); spi.transfer((C)>>0)
 
+    #elif  defined (ILI9225_DRIVER) // Needs gaps between commands + data bytes, so use slower transfer functions
+
+      // These all end in 8 bit mode
+      #define tft_Write_8(C)      spi.transfer(C);
+
+      // Note: the following macros do not wait for the end of transmission
+
+      #define tft_Write_16(C)     spi.transfer16(C)
+
+      #define tft_Write_16N(C)    spi.transfer16(C)
+
+      #define tft_Write_16S(C)    spi.transfer16((C)<<8 | (C)>>8)
+
+      #define tft_Write_32(C)     spi.transfer16((C)>>16); spi.transfer16(C)
+
+      #define tft_Write_32C(C,D)  spi.transfer16(C); spi.transfer16(D)
+
+      #define tft_Write_32D(C)    spi.transfer16(C); spi.transfer16(C)
+
     #else
 
       // This swaps to 8 bit mode, then back to 16 bit mode

Processors/pio_SPI_18bit.pio

@@ -0,0 +1,89 @@
+// Raspberry Pi Pico PIO program to output 18 bit data to a TFT
+// controller via a SPI output data path.
+
+//"Set" set: 1 output pin, TFT_DC
+// Side set: 1 output pin, TFT_SCLK
+// Data set: 1 output pin, TFT_MOSI
+
+.program tft_io
+.side_set 1 opt ;  The TFT_SCLK output.
+
+// The C++ code switches between the 8 bits and 16 bits loops
+// by waiting for the SM to be idle and setting its PC.
+//
+
+// 8 bit transfer
+public start_8:
+   // Pull the next 32 bit value from the TX FIFO. 
+   pull side 0
+   // Lose the top 24 bits, send 1st bit
+   out pins, 25
+   // Now send remaining bits
+   jmp spi_out side 1
+
+public set_addr_window:
+   // Loop count in x for caset, paset and ramwr
+   set x, 2 side 0
+pull_cmd:
+   // Set DC low
+   set pins, 0
+   // Fetch and output LS byte (caset, paset or ramwr), discarding top 24 bits, set WR low
+   pull side 0
+   out pins, 25
+   nop side 1
+next_cmd_bit:
+   out pins, 1 side 0
+   jmp !osre, next_cmd_bit side 1
+   // Set DC high
+   set pins, 1 side 0
+   // Finish if 3rd cmd byte ramwr sent (x == 0)
+   jmp !x, start_tx
+   pull
+next_xy:
+   // send 32 bit start and end coordinates
+   out pins, 1 side 0
+   jmp !osre, next_xy side 1
+   // Loop back for next command
+   jmp x--, pull_cmd side 0
+   // End
+   jmp start_tx
+
+public block_fill:
+   // Fetch colour value
+   pull side 0
+   // Move colour to x
+   mov x, osr
+   // Fetch pixel count
+   pull
+   // Move pixel count to y
+   mov y, osr
+next_16:
+   // Copy colour value back into osr
+   mov osr, x side 0
+   // Lose the top 8 bits, send 1st bit
+   out pins, 9 side 0
+   nop side 1
+next_bit:
+   // Output next remaining bits
+   out pins, 1 side 0
+   // Set TFT_SCLK high and jump for next bit
+   jmp !osre, next_bit side 1
+   // Decrement count and loop
+   jmp y--, next_16 side 0
+   // Now drop back to 16 bit output
+
+.wrap_target
+public start_tx:
+   // Pull the next 32 bit value from the TX FIFO. 
+   // Send the bottom 24 bits
+   pull side 0
+   // Drop the first 8 bits, write first bit
+   out pins, 9 side 0
+   nop side 1
+spi_out:
+   // Output the remaining bits
+   out pins, 1 side 0
+   // Set TFT_SCLK high and jump for next bit
+   jmp !osre, spi_out side 1
+   // Return to start
+.wrap

Processors/pio_SPI_18bit.pio.h

@@ -0,0 +1,73 @@
+// -------------------------------------------------- //
+// This file is autogenerated by pioasm; do not edit! //
+// -------------------------------------------------- //
+
+#pragma once
+
+#if !PICO_NO_HARDWARE
+#include "hardware/pio.h"
+#endif
+
+// ------ //
+// tft_io //
+// ------ //
+
+#define tft_io_wrap_target 27
+#define tft_io_wrap 31
+
+#define tft_io_offset_start_8 0u
+#define tft_io_offset_set_addr_window 3u
+#define tft_io_offset_block_fill 17u
+#define tft_io_offset_start_tx 27u
+
+static const uint16_t tft_io_program_instructions[] = {
+    0x90a0, //  0: pull   block           side 0     
+    0x6019, //  1: out    pins, 25                   
+    0x181e, //  2: jmp    30              side 1     
+    0xf022, //  3: set    x, 2            side 0     
+    0xe000, //  4: set    pins, 0                    
+    0x90a0, //  5: pull   block           side 0     
+    0x6019, //  6: out    pins, 25                   
+    0xb842, //  7: nop                    side 1     
+    0x7001, //  8: out    pins, 1         side 0     
+    0x18e8, //  9: jmp    !osre, 8        side 1     
+    0xf001, // 10: set    pins, 1         side 0     
+    0x003b, // 11: jmp    !x, 27                     
+    0x80a0, // 12: pull   block                      
+    0x7001, // 13: out    pins, 1         side 0     
+    0x18ed, // 14: jmp    !osre, 13       side 1     
+    0x1044, // 15: jmp    x--, 4          side 0     
+    0x001b, // 16: jmp    27                         
+    0x90a0, // 17: pull   block           side 0     
+    0xa027, // 18: mov    x, osr                     
+    0x80a0, // 19: pull   block                      
+    0xa047, // 20: mov    y, osr                     
+    0xb0e1, // 21: mov    osr, x          side 0     
+    0x7009, // 22: out    pins, 9         side 0     
+    0xb842, // 23: nop                    side 1     
+    0x7001, // 24: out    pins, 1         side 0     
+    0x18f8, // 25: jmp    !osre, 24       side 1     
+    0x1095, // 26: jmp    y--, 21         side 0     
+            //     .wrap_target
+    0x90a0, // 27: pull   block           side 0     
+    0x7009, // 28: out    pins, 9         side 0     
+    0xb842, // 29: nop                    side 1     
+    0x7001, // 30: out    pins, 1         side 0     
+    0x18fe, // 31: jmp    !osre, 30       side 1     
+            //     .wrap
+};
+
+#if !PICO_NO_HARDWARE
+static const struct pio_program tft_io_program = {
+    .instructions = tft_io_program_instructions,
+    .length = 32,
+    .origin = -1,
+};
+
+static inline pio_sm_config tft_io_program_get_default_config(uint offset) {
+    pio_sm_config c = pio_get_default_sm_config();
+    sm_config_set_wrap(&c, offset + tft_io_wrap_target, offset + tft_io_wrap);
+    sm_config_set_sideset(&c, 2, true, false);
+    return c;
+}
+#endif

TFT_Drivers/ILI9341_Defines.h

@@ -1,7 +1,7 @@
 // Change the width and height if required (defined in portrait mode)
 // or use the constructor to over-ride defaults
 
-#if defined (ILI9341_DRIVER) || ILI9341_2_DRIVER
+#if defined (ILI9341_DRIVER) || defined (ILI9341_2_DRIVER)
   #define TFT_WIDTH  240
   #define TFT_HEIGHT 320
 #elif defined (ILI9342_DRIVER)

TFT_Drivers/ILI9341_Init.h

@@ -5,7 +5,7 @@
 //
 // See ST7735_Setup.h file for an alternative format
 
-#if defined (ILI9341_DRIVER) | defined (ILI9342_DRIVER)
+#if defined (ILI9341_DRIVER) || defined (ILI9342_DRIVER)
 {
   writecommand(0xEF);
   writedata(0x03);

TFT_eSPI.h

@@ -16,7 +16,7 @@
 #ifndef _TFT_eSPIH_
 #define _TFT_eSPIH_
 
-#define TFT_ESPI_VERSION "2.4.44"
+#define TFT_ESPI_VERSION "2.4.45"
 
 // Bit level feature flags
 // Bit 0 set: viewport capability

keywords.txt

@@ -12,13 +12,17 @@ drawFastHLine	KEYWORD2
 fillRect	KEYWORD2
 height	KEYWORD2
 width	KEYWORD2
+readPixel	KEYWORD2
+setWindow	KEYWORD2
+pushColor	KEYWORD2
+
 setRotation	KEYWORD2
 getRotation	KEYWORD2
 invertDisplay	KEYWORD2
 setAddrWindow	KEYWORD2
-setWindow	KEYWORD2
 
 setViewport	KEYWORD2
+checkViewport	KEYWORD2
 resetViewport	KEYWORD2
 getViewportX	KEYWORD2
 getViewportY	KEYWORD2
@@ -26,28 +30,23 @@ getViewportWidth	KEYWORD2
 getViewportHeight	KEYWORD2
 getViewportDatum	KEYWORD2
 frameViewport	KEYWORD2
-
+resetViewport	KEYWORD2
-# Smooth (anti-aliased) graphics functions
+clipAddrWindow	KEYWORD2
-fillRectHGradient	KEYWORD2
+clipWindow	KEYWORD2
-fillRectVGradient	KEYWORD2
-fillSmoothCircle	KEYWORD2
-fillSmoothRoundRect	KEYWORD2
-drawSpot	KEYWORD2
-drawWideLine	KEYWORD2
-drawWedgeLine	KEYWORD2
-
-pushColor	KEYWORD2
 pushColors	KEYWORD2
 pushBlock	KEYWORD2
 pushPixels	KEYWORD2
-readPixel	KEYWORD2
+
 tft_Read_8	KEYWORD2
 begin_SDA_Read	KEYWORD2
 end_SDA_Read	KEYWORD2
+
 fillScreen	KEYWORD2
+
 drawRect	KEYWORD2
 drawRoundRect	KEYWORD2
 fillRoundRect	KEYWORD2
+
 drawCircle	KEYWORD2
 drawCircleHelper	KEYWORD2
 fillCircle	KEYWORD2
@@ -56,22 +55,28 @@ drawEllipse	KEYWORD2
 fillEllipse	KEYWORD2
 drawTriangle	KEYWORD2
 fillTriangle	KEYWORD2
+
 setSwapBytes	KEYWORD2
 getSwapBytes	KEYWORD2
+
 drawBitmap	KEYWORD2
 drawXBitmap	KEYWORD2
+
 setPivot	KEYWORD2
 getPivotX	KEYWORD2
 getPivotY	KEYWORD2
+
 readRect	KEYWORD2
 pushRect	KEYWORD2
 pushImage	KEYWORD2
 readRectRGB	KEYWORD2
+
 drawNumber	KEYWORD2
 drawFloat	KEYWORD2
 drawString	KEYWORD2
 drawCentreString	KEYWORD2
 drawRightString	KEYWORD2
+
 setCursor	KEYWORD2
 getCursorX	KEYWORD2
 getCursorY	KEYWORD2
@@ -90,13 +95,16 @@ decodeUTF8	KEYWORD2
 write	KEYWORD2
 setCallback	KEYWORD2
 fontsLoaded	KEYWORD2
+
 spiwrite	KEYWORD2
 writecommand	KEYWORD2
+writeRegister	KEYWORD2
 writedata	KEYWORD2
 commandList	KEYWORD2
 readcommand8	KEYWORD2
 readcommand16	KEYWORD2
 readcommand32	KEYWORD2
+
 color565	KEYWORD2
 color8to16	KEYWORD2
 color16to8	KEYWORD2
@@ -104,15 +112,18 @@ color16to24	KEYWORD2
 color24to16	KEYWORD2
 alphaBlend	KEYWORD2
 alphaBlend24	KEYWORD2
+
 initDMA	KEYWORD2
 deInitDMA	KEYWORD2
 pushImageDMA	KEYWORD2
 pushPixelsDMA	KEYWORD2
 dmaBusy	KEYWORD2
 dmaWait	KEYWORD2
+
 startWrite	KEYWORD2
 writeColor	KEYWORD2
 endWrite	KEYWORD2
+
 setAttribute	KEYWORD2
 getAttribute	KEYWORD2
 getSetup	KEYWORD2
@@ -128,6 +139,14 @@ getTouch	KEYWORD2
 calibrateTouch	KEYWORD2
 setTouch	KEYWORD2
 
+# Smooth (anti-aliased) graphics functions
+fillRectHGradient	KEYWORD2
+fillRectVGradient	KEYWORD2
+fillSmoothCircle	KEYWORD2
+fillSmoothRoundRect	KEYWORD2
+drawSpot	KEYWORD2
+drawWideLine	KEYWORD2
+drawWedgeLine	KEYWORD2
 
 # Smooth font functions
 

library.json

@@ -1,6 +1,6 @@
 {
   "name": "TFT_eSPI",
-  "version": "2.4.44",
+  "version": "2.4.45",
   "keywords": "Arduino, tft, display, ttgo, LilyPi, WT32_SC01, ePaper, display, Pico, RP2040 Nano Connect, RP2040, STM32, ESP8266, NodeMCU, ESP32, M5Stack, ILI9341, ST7735, ILI9163, S6D02A1, ILI9481, ILI9486, ILI9488, ST7789, ST7796, RM68140, SSD1351, SSD1963, ILI9225, HX8357D, GC9A01, R61581",
   "description": "A TFT and ePaper SPI graphics library with optimisation for Raspberry Pi Pico, RP2040, ESP8266, ESP32 and STM32",
   "repository":

library.properties

@@ -1,5 +1,5 @@
 name=TFT_eSPI
-version=2.4.44
+version=2.4.45
 author=Bodmer
 maintainer=Bodmer
 sentence=TFT graphics library for Arduino processors with performance optimisation for RP2040, STM32, ESP8266 and ESP32

license.txt

@@ -96,16 +96,16 @@ sketch.
 
 In 2019 the library was adapted to be able to use it with any 32 bit Arduino
 compatible processor. It will run on 8 bit and 16 bit processors but will be
-slow due to extensive use of 32 bit varaibles.
+slow due to extensive use of 32 bit variables.
 
-Many of the example sketches are original work, that contain code created
+Many of the example sketches are original work that contain code created
 for my own projects. For all the original code the FreeBSD licence applies
 and is compatible with the GNU GPL.
 
 vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvStartvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
 Software License Agreement (FreeBSD License)
 
-Copyright (c) 2020 Bodmer (https://github.com/Bodmer)
+Copyright (c) 2022 Bodmer (https://github.com/Bodmer)
 
 All rights reserved.