forked from lucysrausch/hoverboard-firmware-hack
92 lines
5.7 KiB
C
92 lines
5.7 KiB
C
#pragma once
|
|
#include "stm32f1xx_hal.h"
|
|
|
|
// ############################### DO-NOT-TOUCH SETTINGS ###############################
|
|
|
|
#define PWM_FREQ 16000 // PWM frequency in Hz
|
|
#define DEAD_TIME 32 // PWM deadtime
|
|
|
|
#define DELAY_IN_MAIN_LOOP 2 // in ms. default 5. it is independent of all the timing critical stuff. do not touch if you do not know what you are doing.
|
|
|
|
#define TIMEOUT 5 // number of wrong / missing input commands before emergency off
|
|
|
|
// ############################### GENERAL ###############################
|
|
|
|
// How to calibrate: connect GND and RX of a 3.3v uart-usb adapter to the right sensor board cable (be careful not to use the red wire of the cable. 15v will destroye verything.). if you are using nunchuck, disable it temporarily. enable DEBUG_SERIAL_USART3 and DEBUG_SERIAL_ASCII use asearial terminal.
|
|
|
|
// Battery voltage calibration: connect power source. see <How to calibrate>. write value nr 5 to BAT_CALIB_ADC. make and flash firmware. then you can verify voltage on value 6 (devide it by 100.0 to get calibrated voltage).
|
|
#define BAT_CALIB_REAL_VOLTAGE 43.0 // input voltage measured by multimeter
|
|
#define BAT_CALIB_ADC 1704 // adc-value measured by mainboard (value nr 5 on UART debug output)
|
|
|
|
#define BAT_NUMBER_OF_CELLS 10 // normal Hoverboard battery: 10s
|
|
#define BAT_LOW_LVL1_ENABLE 0 // to beep or not to beep, 1 or 0
|
|
#define BAT_LOW_LVL1 3.5 // gently beeps at this voltage level. [V/cell]
|
|
#define BAT_LOW_LVL2_ENABLE 1 // to beep or not to beep, 1 or 0
|
|
#define BAT_LOW_LVL2 3.3 // your battery is almost empty. Charge now! [V/cell]
|
|
#define BAT_LOW_DEAD 3.2 // undervoltage poweroff. (while not driving) [V/cell]
|
|
|
|
#define DC_CUR_LIMIT 15 // DC current limit in amps per motor. so 15 means it will draw 30A out of your battery. it does not disable motors, it is a soft current limit.
|
|
|
|
// Board overheat detection: the sensor is inside the STM/GD chip. it is very inaccurate without calibration (up to 45°C). so only enable this funcion after calibration! let your board cool down. see <How to calibrate>. get the real temp of the chip by thermo cam or another temp-sensor taped on top of the chip and write it to TEMP_CAL_LOW_DEG_C. write debug value 8 to TEMP_CAL_LOW_ADC. drive around to warm up the board. it should be at least 20°C warmer. repeat it for the HIGH-values. enable warning and/or poweroff and make and flash firmware.
|
|
#define TEMP_CAL_LOW_ADC 1655 // temperature 1: ADC value
|
|
#define TEMP_CAL_LOW_DEG_C 35.8 // temperature 1: measured temperature [°C]
|
|
#define TEMP_CAL_HIGH_ADC 1588 // temperature 2: ADC value
|
|
#define TEMP_CAL_HIGH_DEG_C 48.9 // temperature 2: measured temperature [°C]
|
|
#define TEMP_WARNING_ENABLE 0 // to beep or not to beep, 1 or 0, DO NOT ACTIVITE WITHOUT CALIBRATION!
|
|
#define TEMP_WARNING 60 // annoying fast beeps [°C]
|
|
#define TEMP_POWEROFF_ENABLE 0 // to poweroff or not to poweroff, 1 or 0, DO NOT ACTIVITE WITHOUT CALIBRATION!
|
|
#define TEMP_POWEROFF 65 // overheat poweroff. (while not driving) [°C]
|
|
|
|
#define INACTIVITY_TIMEOUT 8 // minutes of not driving until poweroff. it is not very precise.
|
|
|
|
// ############################### SERIAL DEBUG ###############################
|
|
|
|
//#define DEBUG_SERIAL_USART3 // right sensor board cable, disable if I2C (nunchuck or lcd) is used!
|
|
//#define DEBUG_BAUD 115200 // UART baud rate
|
|
//#define DEBUG_SERIAL_SERVOTERM
|
|
//#define DEBUG_SERIAL_ASCII // "1:345 2:1337 3:0 4:0 5:0 6:0 7:0 8:0\r\n"
|
|
|
|
// ###### TRANSPOTTER FIRMWARE #######
|
|
#define CONTROL_GAMETRAK
|
|
#define SUPPORT_LCD
|
|
#define SUPPORT_NUNCHUCK
|
|
//#define SUPPORT_REMOTE
|
|
|
|
#define GAMETRAK_CONNECTION_NORMAL // for normal wireing accoring to the wiki Instructions
|
|
//#define GAMETRAK_CONNECTION_ALTERNATE // use this define instead if you messed up the gametrak ADC wirering (steering is speed, and length of teh wire is steering)
|
|
|
|
#define ROT_P -1.2 // P coefficient for the direction controller. Positive / Negative values to invert gametrak steering direction.
|
|
#define FILTER 0.1 // lower value == softer filter. do not use values <0.01, you will get float precision issues.
|
|
|
|
#define INVERT_R_DIRECTION // Invert right motor
|
|
#define INVERT_L_DIRECTION // Invert left motor
|
|
|
|
// during nunchuck control (only relevant when activated)
|
|
#define SPEED_COEFFICIENT 0.9 // higher value == stronger. 0.0 to ~2.0?
|
|
#define STEER_COEFFICIENT 0.5 // higher value == stronger. if you do not want any steering, set it to 0.0; 0.0 to 1.0
|
|
|
|
#define BEEPS_BACKWARD 1 // 0 or 1
|
|
|
|
|
|
// ############################### VALIDATE SETTINGS ###############################
|
|
|
|
#if defined CONTROL_SERIAL_USART2 && defined CONTROL_ADC
|
|
#error CONTROL_ADC and CONTROL_SERIAL_USART2 not allowed. it is on the same cable.
|
|
#endif
|
|
|
|
#if defined CONTROL_SERIAL_USART2 && defined CONTROL_PPM
|
|
#error CONTROL_PPM and CONTROL_SERIAL_USART2 not allowed. it is on the same cable.
|
|
#endif
|
|
|
|
#if defined DEBUG_SERIAL_USART3 && defined CONTROL_NUNCHUCK
|
|
#error CONTROL_NUNCHUCK and DEBUG_SERIAL_USART3 not allowed. it is on the same cable.
|
|
#endif
|
|
|
|
#if defined DEBUG_SERIAL_USART3 && defined DEBUG_I2C_LCD
|
|
#error DEBUG_I2C_LCD and DEBUG_SERIAL_USART3 not allowed. it is on the same cable.
|
|
#endif
|
|
|
|
#if defined CONTROL_PPM && defined CONTROL_ADC && defined CONTROL_NUNCHUCK || defined CONTROL_PPM && defined CONTROL_ADC || defined CONTROL_ADC && defined CONTROL_NUNCHUCK || defined CONTROL_PPM && defined CONTROL_NUNCHUCK
|
|
#error only 1 input method allowed. use CONTROL_PPM or CONTROL_ADC or CONTROL_NUNCHUCK.
|
|
#endif
|