esp-idf/components/bt/controller/esp32/Kconfig.in

choice BTDM_CTRL_MODE
    prompt "Bluetooth controller mode (BR/EDR/BLE/DUALMODE)"
    help
        Specify the bluetooth controller mode (BR/EDR, BLE or dual mode).

    config BTDM_CTRL_MODE_BLE_ONLY
        bool "BLE Only"

    config BTDM_CTRL_MODE_BR_EDR_ONLY
        bool "BR/EDR Only"

    config BTDM_CTRL_MODE_BTDM
        bool "Bluetooth Dual Mode"

endchoice

config BTDM_CTRL_BLE_MAX_CONN
    int "BLE Max Connections"
    depends on BTDM_CTRL_MODE_BLE_ONLY || BTDM_CTRL_MODE_BTDM
    default 3
    range 1 9
    help
        BLE maximum connections of bluetooth controller.
        Each connection uses 1KB static DRAM whenever the BT controller is enabled.

config BTDM_CTRL_BR_EDR_MIN_ENC_KEY_SZ_DFT
    int "BR/EDR default minimum size of encryption key"
    depends on BTDM_CTRL_MODE_BR_EDR_ONLY || BTDM_CTRL_MODE_BTDM
    default 7
    range 7 16
    help
        BR/EDR default minimum size of encryption key when start encryption.

config BTDM_CTRL_BR_EDR_MAX_ACL_CONN
    int "BR/EDR ACL Max Connections"
    depends on BTDM_CTRL_MODE_BR_EDR_ONLY || BTDM_CTRL_MODE_BTDM
    default 2
    range 1 7
    help
        BR/EDR ACL maximum connections of bluetooth controller.
        Each connection uses 1.2 KB DRAM whenever the BT controller is enabled.

config BTDM_CTRL_BR_EDR_MAX_SYNC_CONN
    int "BR/EDR Sync(SCO/eSCO) Max Connections"
    depends on BTDM_CTRL_MODE_BR_EDR_ONLY || BTDM_CTRL_MODE_BTDM
    default 0
    range 0 3
    help
        BR/EDR Synchronize maximum connections of bluetooth controller.
        Each connection uses 2 KB DRAM whenever the BT controller is enabled.



choice BTDM_CTRL_BR_EDR_SCO_DATA_PATH
    prompt "BR/EDR Sync(SCO/eSCO) default data path"
    depends on BTDM_CTRL_MODE_BR_EDR_ONLY || BTDM_CTRL_MODE_BTDM
    default BTDM_CTRL_BR_EDR_SCO_DATA_PATH_PCM
    help
        SCO data path, i.e. HCI or PCM.
        SCO data can be sent/received through HCI synchronous packets, or the data
        can be routed to on-chip PCM module on ESP32. PCM input/output signals can
        be "matrixed" to GPIOs. The default data path can also be set using API
        "esp_bredr_sco_datapath_set"

    config BTDM_CTRL_BR_EDR_SCO_DATA_PATH_HCI
        bool "HCI"
    config BTDM_CTRL_BR_EDR_SCO_DATA_PATH_PCM
        bool "PCM"
endchoice

config BTDM_CTRL_BR_EDR_SCO_DATA_PATH_EFF
    int
    default 0 if BTDM_CTRL_BR_EDR_SCO_DATA_PATH_HCI
    default 1 if BTDM_CTRL_BR_EDR_SCO_DATA_PATH_PCM
    default 0

menuconfig BTDM_CTRL_PCM_ROLE_EDGE_CONFIG
    bool "PCM Signal Configurations: Role, Polar and Channel Mode(Stereo/Mono)"
    depends on BTDM_CTRL_BR_EDR_SCO_DATA_PATH_PCM
    default y

choice BTDM_CTRL_PCM_ROLE
    prompt "PCM Role"
    depends on BTDM_CTRL_PCM_ROLE_EDGE_CONFIG
    help
        PCM role can be configured as PCM master or PCM slave

    config BTDM_CTRL_PCM_ROLE_MASTER
        bool "PCM Master"
    config BTDM_CTRL_PCM_ROLE_SLAVE
        bool "PCM Slave"
endchoice

choice BTDM_CTRL_PCM_POLAR
    prompt "PCM Polar"
    depends on BTDM_CTRL_PCM_ROLE_EDGE_CONFIG
    help
        PCM polarity can be configured as Falling Edge or Rising Edge

    config BTDM_CTRL_PCM_POLAR_FALLING_EDGE
        bool "Falling Edge"
    config BTDM_CTRL_PCM_POLAR_RISING_EDGE
        bool "Rising Edge"
endchoice

choice BTDM_CTRL_PCM_FSYNCSHP
    prompt "Channel Mode(Stereo/Mono)"
    depends on BTDM_CTRL_PCM_ROLE_EDGE_CONFIG
    default BTDM_CTRL_PCM_FSYNCSHP_STEREO_MODE
    help
        PCM frame synchronization signal shape can be configured as Stereo Mode or Mono Mode.
        (There are detailed instructions under the path examples/bluetooth/bluedroid/classic_bt/hfp_ag/README.md)

    config BTDM_CTRL_PCM_FSYNCSHP_STEREO_MODE
        bool "Stereo Mode"
        help
            Stereo Mode(Dual channel): FSYNC and DOUT signals both change simultaneously on the edge of CLK.
            The FSYNC signal continues until the end of the current channel-data transmission.
            (There is a waveform graph under the path examples/bluetooth/bluedroid/classic_bt/hfp_ag/image)

    config BTDM_CTRL_PCM_FSYNCSHP_MONO_MODE_LF
        bool "Mono Mode 1"
        help
            Mono Mode 1(Single channel): FSYNC signal starts to change a CLK clock cycle earlier than the DOUT signal.
            The FSYNC signal continues for one extra CLK clock cycle.
            (There is a waveform graph under the path examples/bluetooth/bluedroid/classic_bt/hfp_ag/image)

    config BTDM_CTRL_PCM_FSYNCSHP_MONO_MODE_FF
        bool "Mono Mode 2"
        help
            Mono Mode 2(Single channel): FSYNC and DOUT signals both change simultaneously on the edge of CLK.
            The FSYNC signal continues for one extra CLK clock cycle.
            (There is a waveform graph under the path examples/bluetooth/bluedroid/classic_bt/hfp_ag/image)

endchoice

config BTDM_CTRL_PCM_ROLE_EFF
    int
    default 0 if BTDM_CTRL_PCM_ROLE_MASTER
    default 1 if BTDM_CTRL_PCM_ROLE_SLAVE
    default 0

config BTDM_CTRL_PCM_POLAR_EFF
    int
    default 0 if BTDM_CTRL_PCM_POLAR_FALLING_EDGE
    default 1 if BTDM_CTRL_PCM_POLAR_RISING_EDGE
    default 0

config BTDM_CTRL_PCM_FSYNCSHP_EFF
    int
    default 0 if BTDM_CTRL_PCM_FSYNCSHP_STEREO_MODE
    default 1 if BTDM_CTRL_PCM_FSYNCSHP_MONO_MODE_LF
    default 2 if BTDM_CTRL_PCM_FSYNCSHP_MONO_MODE_FF
    default 0

config BTDM_CTRL_AUTO_LATENCY
    bool "Auto latency"
    depends on BTDM_CTRL_MODE_BTDM
    default n
    help
        BLE auto latency, used to enhance classic BT performance
        while classic BT and BLE are enabled at the same time.

config BTDM_CTRL_AUTO_LATENCY_EFF
    bool
    default BTDM_CTRL_AUTO_LATENCY if BTDM_CTRL_MODE_BTDM
    default n

config BTDM_CTRL_LEGACY_AUTH_VENDOR_EVT
    bool "Legacy Authentication Vendor Specific Event Enable"
    depends on BTDM_CTRL_MODE_BR_EDR_ONLY || BTDM_CTRL_MODE_BTDM
    default y
    help
        To protect from BIAS attack during Legacy authentication,
        Legacy authentication Vendor specific event should be enabled

config BTDM_CTRL_LEGACY_AUTH_VENDOR_EVT_EFF
    bool
    default BTDM_CTRL_LEGACY_AUTH_VENDOR_EVT if BTDM_CTRL_MODE_BR_EDR_ONLY || BTDM_CTRL_MODE_BTDM
    default 0


config BTDM_CTRL_BLE_MAX_CONN_EFF
    int
    default BTDM_CTRL_BLE_MAX_CONN if BTDM_CTRL_MODE_BLE_ONLY || BTDM_CTRL_MODE_BTDM
    default 0

config BTDM_CTRL_BR_EDR_MIN_ENC_KEY_SZ_DFT_EFF
    int
    default BTDM_CTRL_BR_EDR_MIN_ENC_KEY_SZ_DFT if BTDM_CTRL_MODE_BR_EDR_ONLY || BTDM_CTRL_MODE_BTDM
    default 0

config BTDM_CTRL_BR_EDR_MAX_ACL_CONN_EFF
    int
    default BTDM_CTRL_BR_EDR_MAX_ACL_CONN if BTDM_CTRL_MODE_BR_EDR_ONLY || BTDM_CTRL_MODE_BTDM
    default 0

config BTDM_CTRL_BR_EDR_MAX_SYNC_CONN_EFF
    int
    default BTDM_CTRL_BR_EDR_MAX_SYNC_CONN if BTDM_CTRL_MODE_BR_EDR_ONLY || BTDM_CTRL_MODE_BTDM
    default 0

choice BTDM_CTRL_PINNED_TO_CORE_CHOICE
    prompt "The cpu core which bluetooth controller run"
    depends on !FREERTOS_UNICORE
    help
        Specify the cpu core to run bluetooth controller.
        Can not specify no-affinity.

    config BTDM_CTRL_PINNED_TO_CORE_0
        bool "Core 0 (PRO CPU)"
    config BTDM_CTRL_PINNED_TO_CORE_1
        bool "Core 1 (APP CPU)"
        depends on !FREERTOS_UNICORE
endchoice

config BTDM_CTRL_PINNED_TO_CORE
    int
    default 0 if BTDM_CTRL_PINNED_TO_CORE_0
    default 1 if BTDM_CTRL_PINNED_TO_CORE_1
    default 0

choice BTDM_CTRL_HCI_MODE_CHOICE
    prompt "HCI mode"
    help
        Specify HCI mode as VHCI or UART(H4)

    config BTDM_CTRL_HCI_MODE_VHCI
        bool "VHCI"
        help
            Normal option. Mostly, choose this VHCI when bluetooth host run on ESP32, too.

    config BTDM_CTRL_HCI_MODE_UART_H4
        bool "UART(H4)"
        help
            If use external bluetooth host which run on other hardware and use UART as the HCI interface,
            choose this option.
endchoice

menu "HCI UART(H4) Options"
    visible if BTDM_CTRL_HCI_MODE_UART_H4

    config BTDM_CTRL_HCI_UART_NO
        int "UART Number for HCI"
        depends on BTDM_CTRL_HCI_MODE_UART_H4
        range 1 2
        default 1
        help
            Uart number for HCI. The available uart is UART1 and UART2.

    config BTDM_CTRL_HCI_UART_BAUDRATE
        int "UART Baudrate for HCI"
        depends on BTDM_CTRL_HCI_MODE_UART_H4
        range 115200 921600
        default 921600
        help
            UART Baudrate for HCI. Please use standard baudrate.

    config BTDM_CTRL_HCI_UART_FLOW_CTRL_EN
        bool "Enable UART flow control"
        depends on BTDM_CTRL_HCI_MODE_UART_H4
        default y

endmenu

menu "MODEM SLEEP Options"
    config BTDM_CTRL_MODEM_SLEEP
        bool "Bluetooth modem sleep"
        default y
        help
            Enable/disable bluetooth controller low power mode.

    choice BTDM_CTRL_MODEM_SLEEP_MODE
        prompt "Bluetooth Modem sleep mode"
        depends on BTDM_CTRL_MODEM_SLEEP
        help
            To select which strategy to use for modem sleep

        config BTDM_CTRL_MODEM_SLEEP_MODE_ORIG
            bool "ORIG Mode(sleep with low power clock)"
            help
                ORIG mode is a bluetooth sleep mode that can be used for dual mode controller. In this mode,
                bluetooth controller sleeps between BR/EDR frames and BLE events. A low power clock is used to
                maintain bluetooth reference clock.

        config BTDM_CTRL_MODEM_SLEEP_MODE_EVED
            bool "EVED Mode(For internal test only)"
            help
                EVED mode is for BLE only and is only for internal test. Do not use it for production. this
                mode is not compatible with DFS nor light sleep
    endchoice

    choice BTDM_CTRL_LOW_POWER_CLOCK
        prompt "Bluetooth low power clock"
        depends on BTDM_CTRL_MODEM_SLEEP_MODE_ORIG
        help
            Select the low power clock source for bluetooth controller. Bluetooth low power clock is
            the clock source to maintain time in sleep mode.

            - "Main crystal" option provides good accuracy and can support Dynamic Frequency Scaling
              to be used with Bluetooth modem sleep. Light sleep is not supported.
            - "External 32kHz crystal" option allows user to use a 32.768kHz crystal as Bluetooth low
              power clock. This option is allowed as long as External 32kHz crystal is configured as
              the system RTC clock source. This option provides good accuracy and supports Bluetooth
              modem sleep to be used alongside Dynamic Frequency Scaling or light sleep.

        config BTDM_CTRL_LPCLK_SEL_MAIN_XTAL
            bool "Main crystal"
            help
                Main crystal can be used as low power clock for bluetooth modem sleep. If this option is
                selected, bluetooth modem sleep can work under Dynamic Frequency Scaling(DFS) enabled, but
                cannot work when light sleep is enabled. Main crystal has a good performance in accuracy as
                the bluetooth low power clock source.

        config BTDM_CTRL_LPCLK_SEL_EXT_32K_XTAL
            bool "External 32kHz crystal/oscillator"
            depends on RTC_CLK_SRC_EXT_CRYS || RTC_CLK_SRC_EXT_OSC
            help
                External 32kHz crystal/oscillator has a nominal frequency of 32.768kHz and provides good frequency
                stability. If used as Bluetooth low power clock, External 32kHz can support Bluetooth
                modem sleep to be used with both DFS and light sleep.
    endchoice

endmenu

choice BTDM_BLE_SLEEP_CLOCK_ACCURACY
    prompt "BLE Sleep Clock Accuracy"
    depends on BTDM_CTRL_MODE_BLE_ONLY || BTDM_CTRL_MODE_BTDM
    default BTDM_BLE_DEFAULT_SCA_250PPM
    help
        BLE Sleep Clock Accuracy(SCA) for the local device is used to estimate window widening in BLE
        connection events. With a lower level of clock accuracy(e.g. 500ppm over 250ppm), the slave
        needs a larger RX window to synchronize with master in each anchor point, thus resulting in an
        increase of power consumption but a higher level of robustness in keeping connected. According
        to the requirements of Bluetooth Core specification 4.2, the worst-case accuracy of Classic
        Bluetooth Low Power Oscillator (LPO) is +/-250ppm in STANDBY and in low power modes such as
        sniff. For BLE the worst-case SCA is +/-500ppm.

        - "151ppm to 250ppm" option is the default value for Bluetooth Dual mode
        - "251ppm to 500ppm" option can be used in BLE only mode when using external 32kHz crystal as
           low power clock. This option is provided in case that BLE sleep clock has a lower level of
           accuracy, or other error sources contribute to the inaccurate timing during sleep.

    config BTDM_BLE_DEFAULT_SCA_500PPM
        bool "251ppm to 500ppm"
        depends on BTDM_CTRL_LPCLK_SEL_EXT_32K_XTAL && BTDM_CTRL_MODE_BLE_ONLY
    config BTDM_BLE_DEFAULT_SCA_250PPM
        bool "151ppm to 250ppm"
endchoice
config BTDM_BLE_SLEEP_CLOCK_ACCURACY_INDEX_EFF
    int
    default 0 if BTDM_BLE_DEFAULT_SCA_500PPM
    default 1 if BTDM_BLE_DEFAULT_SCA_250PPM
    default 1

config BTDM_BLE_SCAN_DUPL
    bool "BLE Scan Duplicate Options"
    depends on (BTDM_CTRL_MODE_BTDM || BTDM_CTRL_MODE_BLE_ONLY)
    default y
    help
        This select enables parameters setting of BLE scan duplicate.

choice BTDM_SCAN_DUPL_TYPE
    prompt "Scan Duplicate Type"
    default BTDM_SCAN_DUPL_TYPE_DEVICE
    depends on BTDM_BLE_SCAN_DUPL
    help
        Scan duplicate have three ways. one is "Scan Duplicate By Device Address", This way is to use
        advertiser address filtering. The adv packet of the same address is only allowed to be reported once.
        Another way is "Scan Duplicate By Device Address And Advertising Data". This way is to use advertising
        data and device address filtering. All different adv packets with the same address are allowed to be
        reported. The last way is "Scan Duplicate By Advertising Data". This way is to use advertising data
        filtering. All same advertising data only allow to be reported once even though they are from
        different devices.

    config BTDM_SCAN_DUPL_TYPE_DEVICE
        bool "Scan Duplicate By Device Address"
        help
            This way is to use advertiser address filtering. The adv packet of the same address is only
            allowed to be reported once

    config BTDM_SCAN_DUPL_TYPE_DATA
        bool "Scan Duplicate By Advertising Data"
        help
            This way is to use advertising data filtering. All same advertising data only allow to be reported
            once even though they are from different devices.

    config BTDM_SCAN_DUPL_TYPE_DATA_DEVICE
        bool "Scan Duplicate By Device Address And Advertising Data"
        help
            This way is to use advertising data and device address filtering. All different adv packets with
            the same address are allowed to be reported.
endchoice

config BTDM_SCAN_DUPL_TYPE
    int
    depends on BTDM_BLE_SCAN_DUPL
    default 0 if BTDM_SCAN_DUPL_TYPE_DEVICE
    default 1 if BTDM_SCAN_DUPL_TYPE_DATA
    default 2 if BTDM_SCAN_DUPL_TYPE_DATA_DEVICE
    default 0

config BTDM_SCAN_DUPL_CACHE_SIZE
    int "Maximum number of devices in scan duplicate filter"
    depends on BTDM_BLE_SCAN_DUPL
    range 10 1000
    default 100
    help
        Maximum number of devices which can be recorded in scan duplicate filter.
        When the maximum amount of device in the filter is reached, the oldest device will be refreshed.

config BTDM_SCAN_DUPL_CACHE_REFRESH_PERIOD
    int "Duplicate scan list refresh period (seconds)"
    depends on BTDM_BLE_SCAN_DUPL
    range 0 1000
    default 0
    help
        If the period value is non-zero, the controller will periodically clear the device information
        stored in the scan duuplicate filter. If it is 0, the scan duuplicate filter will not be cleared
        until the scanning is disabled. Duplicate advertisements for this period should not be sent to the
        Host in advertising report events.
        There are two scenarios where the ADV packet will be repeatedly reported:
        1. The duplicate scan cache is full, the controller will delete the oldest device information and
        add new device information.
        2. When the refresh period is up, the controller will clear all device information and start filtering
        again.

config BTDM_BLE_MESH_SCAN_DUPL_EN
    bool "Special duplicate scan mechanism for BLE Mesh scan"
    depends on BTDM_BLE_SCAN_DUPL
    default n
    help
        This enables the BLE scan duplicate for special BLE Mesh scan.

config BTDM_MESH_DUPL_SCAN_CACHE_SIZE
    int "Maximum number of Mesh adv packets in scan duplicate filter"
    depends on BTDM_BLE_MESH_SCAN_DUPL_EN
    range 10 1000
    default 100
    help
        Maximum number of adv packets which can be recorded in duplicate scan cache for BLE Mesh.
        When the maximum amount of device in the filter is reached, the cache will be refreshed.

config BTDM_CTRL_FULL_SCAN_SUPPORTED
    bool "BLE full scan feature supported"
    depends on BTDM_CTRL_MODE_BLE_ONLY || BTDM_CTRL_MODE_BTDM
    default y
    help
        The full scan function is mainly used to provide BLE scan performance.
        This is required for scenes with high scan performance requirements, such as BLE Mesh scenes.

config BTDM_CTRL_SCAN_BACKOFF_UPPERLIMITMAX
    bool "Disable active scan backoff"
    default n
    help
        Disable active scan backoff. The bluetooth spec requires that scanners should run a backoff procedure to
        minimize collision of scan request PDUs from multiple scanners. If scan backoff is disabled, in active
        scanning, scan request PDU will be sent every time when HW receives scannable ADV PDU.

config BTDM_CTRL_CHECK_CONNECT_IND_ACCESS_ADDRESS
    bool "Enable enhanced Access Address check in CONNECT_IND"
    depends on (BTDM_CTRL_MODE_BLE_ONLY || BTDM_CTRL_MODE_BTDM)
    default n
    help
        Enabling this option will add stricter verification of the Access Address in the CONNECT_IND PDU.
        This improves security by ensuring that only connection requests with valid Access Addresses are accepted.
        If disabled, only basic checks are applied, improving compatibility.


config BTDM_BLE_ADV_REPORT_FLOW_CTRL_SUPP
    bool "BLE adv report flow control supported"
    depends on (BTDM_CTRL_MODE_BTDM || BTDM_CTRL_MODE_BLE_ONLY)
    default y
    help
        The function is mainly used to enable flow control for advertising reports. When it is enabled,
        advertising reports will be discarded by the controller if the number of unprocessed advertising
        reports exceeds the size of BLE adv report flow control.

config BTDM_BLE_ADV_REPORT_FLOW_CTRL_NUM
    int "BLE adv report flow control number"
    depends on BTDM_BLE_ADV_REPORT_FLOW_CTRL_SUPP
    range 50 1000
    default 100
    help
        The number of unprocessed advertising report that Bluedroid can save.If you set
        `BTDM_BLE_ADV_REPORT_FLOW_CTRL_NUM` to a small value, this may cause adv packets lost.
        If you set `BTDM_BLE_ADV_REPORT_FLOW_CTRL_NUM` to a large value, Bluedroid may cache a
        lot of adv packets and this may cause system memory run out. For example, if you set
        it to 50, the maximum memory consumed by host is 35 * 50 bytes. Please set
        `BTDM_BLE_ADV_REPORT_FLOW_CTRL_NUM` according to your system free memory and handle adv
        packets as fast as possible, otherwise it will cause adv packets lost.

config BTDM_BLE_ADV_REPORT_DISCARD_THRSHOLD
    int "BLE adv lost event threshold value"
    depends on BTDM_BLE_ADV_REPORT_FLOW_CTRL_SUPP
    range 1 1000
    default 20
    help
        When adv report flow control is enabled, The ADV lost event will be generated when the number
        of ADV packets lost in the controller reaches this threshold. It is better to set a larger value.
        If you set `BTDM_BLE_ADV_REPORT_DISCARD_THRSHOLD` to a small value or printf every adv lost event, it
        may cause adv packets lost more.

menu "BLE disconnects when Instant Passed (0x28) occurs"
    config BTDM_BLE_LLCP_CONN_UPDATE
        bool "BLE ACL connection update procedure"
        depends on (BTDM_CTRL_MODE_BLE_ONLY || BTDM_CTRL_MODE_BTDM)
        default n
        help
            If this option is enabled, Controller will terminate the connection
            when Instant Passed (0x28) error occurs during connection update procedure.

    config BTDM_BLE_LLCP_CHAN_MAP_UPDATE
        bool "BLE ACL channel map update procedure"
        depends on (BTDM_CTRL_MODE_BLE_ONLY || BTDM_CTRL_MODE_BTDM)
        default n
        help
            If this option is enabled, Controller will terminate the connection
            when Instant Passed (0x28) error occurs in channel map update procedure.
endmenu

config BTDM_BLE_CHAN_ASS_EN
    bool "Enable channel assessment"
    depends on (BTDM_CTRL_MODE_BLE_ONLY || BTDM_CTRL_MODE_BTDM)
    default y
    help
        If this option is enabled, The Controller will records the communication quality
        for each channel and then start a timer to check and update the channel map every 4 seconds.

config BTDM_BLE_PING_EN
    bool "Enable LE Ping procedure"
    depends on (BTDM_CTRL_MODE_BTDM || BTDM_CTRL_MODE_BLE_ONLY)
    default y
    help
        If this option is disabled, The Controller will not start the LE authenticated payload timer.
        This option is used for some compatibility problems related to LE ping procedure.

config BTDM_CTRL_CONTROLLER_DEBUG_MODE_1
    bool "Enable Bluetooth controller debugging mode 1 (for internal use only)"
    default n
    depends on BT_ENABLED
    help
        Enables specific debugging features for the Bluetooth controller.
        This option is strictly for internal debugging purposes and should not be enabled in production environments,
        as it may impact performance and stability.

config BTDM_RESERVE_DRAM
    hex
    default 0xdb5c if BT_ENABLED
    default 0

config BTDM_CTRL_HLI
    bool "High level interrupt"
    depends on BT_ENABLED
    default y
    help
        Using Level 4 interrupt for Bluetooth.