diff --git a/docs/en/api-guides/jtag-debugging/configure-builtin-jtag.rst b/docs/en/api-guides/jtag-debugging/configure-builtin-jtag.rst
index 114bcfb553..40bbdaf051 100644
--- a/docs/en/api-guides/jtag-debugging/configure-builtin-jtag.rst
+++ b/docs/en/api-guides/jtag-debugging/configure-builtin-jtag.rst
@@ -8,8 +8,8 @@ Configure {IDF_TARGET_NAME} Built-in JTAG Interface
 
 :link_to_translation:`zh_CN:[中文]`
 
-{IDF_TARGET_JTAG_PIN_Dneg:default="Not Updated!", esp32c3="GPIO18", esp32c6="GPIO12", esp32s3="GPIO19", esp32h2="GPIO26", esp32p4="GPIO25"}
-{IDF_TARGET_JTAG_PIN_Dpos:default="Not Updated!", esp32c3="GPIO19", esp32c6="GPIO13", esp32s3="GPIO20", esp32h2="GPIO27", esp32p4="GPIO24"}
+{IDF_TARGET_JTAG_PIN_Dneg:default="Not Updated!", esp32c3="GPIO18", esp32c6="GPIO12", esp32s3="GPIO19", esp32h2="GPIO26", esp32p4="GPIO24"}
+{IDF_TARGET_JTAG_PIN_Dpos:default="Not Updated!", esp32c3="GPIO19", esp32c6="GPIO13", esp32s3="GPIO20", esp32h2="GPIO27", esp32p4="GPIO25"}
 
 {IDF_TARGET_NAME} has built-in JTAG circuitry and can be debugged without any additional chip. Only a USB cable connected to the D+/D- pins is necessary. For dev kits without an exposed USB Serial Jtag connector, a USB breakout cable can be used. The necessary connections are shown in the following section.
 
diff --git a/docs/zh_CN/api-guides/jtag-debugging/configure-builtin-jtag.rst b/docs/zh_CN/api-guides/jtag-debugging/configure-builtin-jtag.rst
index efd6482b7c..3125a6056d 100644
--- a/docs/zh_CN/api-guides/jtag-debugging/configure-builtin-jtag.rst
+++ b/docs/zh_CN/api-guides/jtag-debugging/configure-builtin-jtag.rst
@@ -8,8 +8,8 @@
 
 :link_to_translation:`en:[English]`
 
-{IDF_TARGET_JTAG_PIN_Dneg:default="未更新!", esp32c3="GPIO18", esp32c6="GPIO12", esp32s3="GPIO19", esp32h2="GPIO26", esp32p4="GPIO25"}
-{IDF_TARGET_JTAG_PIN_Dpos:default="未更新!", esp32c3="GPIO19", esp32c6="GPIO13", esp32s3="GPIO20", esp32h2="GPIO27", esp32p4="GPIO24"}
+{IDF_TARGET_JTAG_PIN_Dneg:default="未更新!", esp32c3="GPIO18", esp32c6="GPIO12", esp32s3="GPIO19", esp32h2="GPIO26", esp32p4="GPIO24"}
+{IDF_TARGET_JTAG_PIN_Dpos:default="未更新!", esp32c3="GPIO19", esp32c6="GPIO13", esp32s3="GPIO20", esp32h2="GPIO27", esp32p4="GPIO25"}
 
 {IDF_TARGET_NAME} 内置了 JTAG 电路，无需额外的芯片即可进行调试。只需将 USB 线连接到 D+/D- 引脚即可。对于没有外露 USB 串行 JTAG 连接器的开发板，可以使用 USB 转接线。所需的连接方式将在下一节中介绍。
 
diff --git a/docs/zh_CN/get-started/establish-serial-connection.rst b/docs/zh_CN/get-started/establish-serial-connection.rst
index 59cf04bbb4..604f8fcb6e 100644
--- a/docs/zh_CN/get-started/establish-serial-connection.rst
+++ b/docs/zh_CN/get-started/establish-serial-connection.rst
@@ -142,7 +142,7 @@
     {IDF_TARGET_NAME} 支持 USB 外设，无需外部 USB 至 UART 桥，即可烧录二进制文件。
 
     {IDF_TARGET_USB_PIN_DM:default="尚未更新！", esp32c3="GPIO18", esp32s3="GPIO19", esp32s2="GPIO19", esp32c6="GPIO12", esp32h2="GPIO26", esp32p4="GPIO24/26"}
-    {IDF_TARGET_USB_PIN_DP:default="尚未更新！", esp32c3="GPIO19", esp32s3="GPIO20", esp32s2="GPIO20", esp32c6="GPIO13", esp32h2="GPIO27", esp32p4="GPIO24/26"}
+    {IDF_TARGET_USB_PIN_DP:default="尚未更新！", esp32c3="GPIO19", esp32s3="GPIO20", esp32s2="GPIO20", esp32c6="GPIO13", esp32h2="GPIO27", esp32p4="GPIO25/27"}
 
     {IDF_TARGET_NAME} 上的 USB 使用 **{IDF_TARGET_USB_PIN_DP}** 作为 **D+**， **{IDF_TARGET_USB_PIN_DM}** 作为 **D-**。