diff --git a/components/esp_hw_support/Kconfig b/components/esp_hw_support/Kconfig
index 0d6dd965a0..f339154bcf 100644
--- a/components/esp_hw_support/Kconfig
+++ b/components/esp_hw_support/Kconfig
@@ -91,6 +91,13 @@ menu "Hardware Settings"
                 To reduce leakage current, some types of SPI Flash/RAM only need to pull up the CS pin
                 during light sleep. But there are also some kinds of SPI Flash/RAM that need to pull up
                 all pins. It depends on the SPI Flash/RAM chip used.
+
+        config ESP_SLEEP_GPIO_ENABLE_INTERNAL_RESISTORS
+            bool "Allow to enable internal pull-up/downs for the Deep-Sleep wakeup IOs"
+            default y
+            help
+                When using rtc gpio wakeup source during deepsleep without external pull-up/downs, you may want to
+                make use of the internal ones.
     endmenu
 
     menu "ESP_SLEEP_WORKAROUND"
diff --git a/components/esp_hw_support/include/esp_sleep.h b/components/esp_hw_support/include/esp_sleep.h
index fa81bd92e1..ca98bb34a5 100644
--- a/components/esp_hw_support/include/esp_sleep.h
+++ b/components/esp_hw_support/include/esp_sleep.h
@@ -245,9 +245,13 @@ esp_err_t esp_sleep_enable_ext1_wakeup(uint64_t mask, esp_sleep_ext1_wakeup_mode
  * @note This function does not modify pin configuration. The pins are
  *       configured inside esp_deep_sleep_start, immediately before entering sleep mode.
  *
- * @note You don't need to care to pull-up or pull-down before using this
- *       function, because this will be set internally in esp_deep_sleep_start
- *       based on the wakeup mode. BTW, when you use low level to wake up the
+ * @note You don't need to worry about pull-up or pull-down resistors before
+ *       using this function because the ESP_SLEEP_GPIO_ENABLE_INTERNAL_RESISTORS
+ *       option is enabled by default. It will automatically set pull-up or pull-down
+ *       resistors internally in esp_deep_sleep_start based on the wakeup mode. However,
+ *       when using external pull-up or pull-down resistors, please be sure to disable
+ *       the ESP_SLEEP_GPIO_ENABLE_INTERNAL_RESISTORS option, as the combination of internal
+ *       and external resistors may cause interference. BTW, when you use low level to wake up the
  *       chip, we strongly recommend you to add external resistors (pull-up).
  *
  * @param gpio_pin_mask  Bit mask of GPIO numbers which will cause wakeup. Only GPIOs
diff --git a/components/esp_hw_support/sleep_modes.c b/components/esp_hw_support/sleep_modes.c
index ea8fb5b557..0efbcc3b76 100644
--- a/components/esp_hw_support/sleep_modes.c
+++ b/components/esp_hw_support/sleep_modes.c
@@ -1165,6 +1165,7 @@ static void gpio_deep_sleep_wakeup_prepare(void)
         if (((1ULL << gpio_idx) & s_config.gpio_wakeup_mask) == 0) {
             continue;
         }
+#if CONFIG_ESP_SLEEP_GPIO_ENABLE_INTERNAL_RESISTORS
         if (s_config.gpio_trigger_mode & BIT(gpio_idx)) {
             ESP_ERROR_CHECK(gpio_pullup_dis(gpio_idx));
             ESP_ERROR_CHECK(gpio_pulldown_en(gpio_idx));
@@ -1172,6 +1173,7 @@ static void gpio_deep_sleep_wakeup_prepare(void)
             ESP_ERROR_CHECK(gpio_pullup_en(gpio_idx));
             ESP_ERROR_CHECK(gpio_pulldown_dis(gpio_idx));
         }
+#endif
         ESP_ERROR_CHECK(gpio_hold_en(gpio_idx));
     }
     // Clear state from previous wakeup