Update several Kconfig files to make help texts compatible with ReST

components/esp32/Kconfig

@@ -253,6 +253,7 @@ choice CONSOLE_UART
     default CONSOLE_UART_DEFAULT
     help
         Select whether to use UART for console output (through stdout and stderr).
+        
         - Default is to use UART0 on pins GPIO1(TX) and GPIO3(RX).
         - If "Custom" is selected, UART0 or UART1 can be chosen,
           and any pins can be selected.
@@ -315,22 +316,17 @@ config ULP_COPROC_ENABLED
         If this option is enabled, further coprocessor configuration will appear in the Components menu.
 
 config ULP_COPROC_RESERVE_MEM
-    int "RTC slow memory reserved for coprocessor"
+    int
-    default 512
+    prompt "RTC slow memory reserved for coprocessor" if ULP_COPROC_ENABLED
-    range 32 8192
+    default 512 if ULP_COPROC_ENABLED
-    depends on ULP_COPROC_ENABLED
+    range 32 8192 if ULP_COPROC_ENABLED
+    default 0 if !ULP_COPROC_ENABLED
+    range 0 0 if !ULP_COPROC_ENABLED
     help
         Bytes of memory to reserve for ULP coprocessor firmware & data.
 
         Data is reserved at the beginning of RTC slow memory.
 
-# Set CONFIG_ULP_COPROC_RESERVE_MEM to 0 if ULP is disabled
-config ULP_COPROC_RESERVE_MEM
-    int
-    default 0
-    depends on !ULP_COPROC_ENABLED
-
-
 choice ESP32_PANIC
     prompt "Panic handler behaviour"
     default ESP32_PANIC_PRINT_REBOOT
@@ -542,6 +538,7 @@ config ESP32_RTC_CLK_CAL_CYCLES
         
         When this option is set to 0, clock calibration will not be performed at
         startup, and approximate clock frequencies will be assumed:
+
         - 150000 Hz if internal RC oscillator is used as clock source
         - 32768 Hz if the 32k crystal oscillator is used
 
@@ -568,8 +565,10 @@ choice ESP32_XTAL_FREQ_SEL
     default ESP32_XTAL_FREQ_AUTO
     help
         ESP32 currently supports the following XTAL frequencies:
-            - 26 MHz
+
-            - 40 MHz
+        - 26 MHz
+        - 40 MHz
+
         Startup code can automatically estimate XTAL frequency. This feature
         uses the internal 8MHz oscillator as a reference. Because the internal
         oscillator frequency is temperature dependent, it is not recommended
@@ -591,8 +590,6 @@ config ESP32_XTAL_FREQ
     default 40 if ESP32_XTAL_FREQ_40
     default 26 if ESP32_XTAL_FREQ_26
 
-endmenu
-
 config NO_BLOBS
     bool "No Binary Blobs"
     depends on !BT_ENABLED
@@ -601,6 +598,8 @@ config NO_BLOBS
        If enabled, this disables the linking of binary libraries in the application build. Note
        that after enabling this Wi-Fi/Bluetooth will not work.
 
+endmenu
+
 menu Wi-Fi
 
 config SW_COEXIST_ENABLE

components/freertos/Kconfig

@@ -240,7 +240,7 @@ config ENABLE_STATIC_TASK_CLEAN_UP_HOOK
     help
         Enable this option to make FreeRTOS call the static task clean up hook when a task is deleted.
 
-        Bear in mind that if this option is enabled you will need to implement the following function:
+        Bear in mind that if this option is enabled you will need to implement the following function::
 
             void vPortCleanUpTCB ( void *pxTCB ) {
                 // place clean up code here

components/partition_table/Kconfig.projbuild

@@ -1,6 +1,6 @@
 menu "Partition Table"
 
-choice
+choice PARTITION_TABLE_TYPE
     prompt "Partition Table"
     default PARTITION_TABLE_SINGLE_APP
     help

components/spi_flash/Kconfig

@@ -5,9 +5,11 @@ config SPI_FLASH_ENABLE_COUNTERS
     default 0
     help
         This option enables the following APIs:
-            spi_flash_reset_counters
+            
-            spi_flash_dump_counters
+        - spi_flash_reset_counters
-            spi_flash_get_counters
+        - spi_flash_dump_counters
+        - spi_flash_get_counters
+        
         These APIs may be used to collect performance data for spi_flash APIs
         and to help understand behaviour of libraries which use SPI flash.