/* * SPDX-FileCopyrightText: 2022 Espressif Systems (Shanghai) CO LTD * * SPDX-License-Identifier: Apache-2.0 */ /** * This file is specified for I2S PDM communication mode * Features: * - Only support PDM tx/rx mode * - Fixed to 2 slots * - Data bit width only support 16 bits */ #pragma once #include "hal/i2s_types.h" #include "hal/gpio_types.h" #include "driver/i2s_common.h" #ifdef __cplusplus extern "C" { #endif #if SOC_I2S_SUPPORTS_PDM_RX /** * @brief PDM format in 2 slots(RX) * @param bits_per_sample i2s data bit width, only support 16 bits for PDM mode * @param mono_or_stereo I2S_SLOT_MODE_MONO or I2S_SLOT_MODE_STEREO */ #define I2S_PDM_RX_SLOT_DEFAULT_CONFIG(bits_per_sample, mono_or_stereo) { \ .data_bit_width = bits_per_sample, \ .slot_bit_width = I2S_SLOT_BIT_WIDTH_AUTO, \ .slot_mode = mono_or_stereo, \ .slot_mask = (mono_or_stereo == I2S_SLOT_MODE_MONO) ? \ I2S_PDM_SLOT_LEFT : I2S_PDM_SLOT_BOTH, \ } /** * @brief i2s default pdm rx clock configuration * @param rate sample rate */ #define I2S_PDM_RX_CLK_DEFAULT_CONFIG(rate) { \ .sample_rate_hz = rate, \ .clk_src = I2S_CLK_SRC_DEFAULT, \ .mclk_multiple = I2S_MCLK_MULTIPLE_256, \ .dn_sample_mode = I2S_PDM_DSR_8S \ } /** * @brief I2S slot configuration for pdm rx mode */ typedef struct { /* General fields */ i2s_data_bit_width_t data_bit_width; /*!< I2S sample data bit width (valid data bits per sample), only support 16 bits for PDM mode */ i2s_slot_bit_width_t slot_bit_width; /*!< I2S slot bit width (total bits per slot) , only support 16 bits for PDM mode */ i2s_slot_mode_t slot_mode; /*!< Set mono or stereo mode with I2S_SLOT_MODE_MONO or I2S_SLOT_MODE_STEREO */ /* Particular fields */ i2s_pdm_slot_mask_t slot_mask; /*!< Choose the slots to activate */ } i2s_pdm_rx_slot_config_t; /** * @brief I2S clock configuration for pdm rx mode */ typedef struct { /* General fields */ uint32_t sample_rate_hz; /*!< I2S sample rate */ i2s_clock_src_t clk_src; /*!< Choose clock source */ i2s_mclk_multiple_t mclk_multiple; /*!< The multiple of mclk to the sample rate */ /* Particular fields */ i2s_pdm_dsr_t dn_sample_mode; /*!< Down-sampling rate mode */ } i2s_pdm_rx_clk_config_t; /** * @brief I2S PDM tx mode GPIO pins configuration */ typedef struct { gpio_num_t clk; /*!< PDM clk pin, output */ union { gpio_num_t din; /*!< DATA pin 0, input */ gpio_num_t dins[SOC_I2S_PDM_MAX_RX_LINES]; /*!< DATA pins, input, only take effect when corresponding I2S_PDM_RX_LINEx_SLOT_xxx is enabled in i2s_pdm_rx_slot_config_t::slot_mask */ }; struct { uint32_t clk_inv: 1; /*!< Set 1 to invert the clk output */ } invert_flags; /*!< GPIO pin invert flags */ } i2s_pdm_rx_gpio_config_t; /** * @brief I2S PDM RX mode major configuration that including clock/slot/gpio configuration */ typedef struct { i2s_pdm_rx_clk_config_t clk_cfg; /*!< PDM RX clock configurations, can be genertated by macro I2S_PDM_RX_CLK_DEFAULT_CONFIG */ i2s_pdm_rx_slot_config_t slot_cfg; /*!< PDM RX slot configurations, can be genertated by macro I2S_PDM_RX_SLOT_DEFAULT_CONFIG */ i2s_pdm_rx_gpio_config_t gpio_cfg; /*!< PDM RX slot configurations, specified by user */ } i2s_pdm_rx_config_t; /** * @brief Initialize i2s channel to PDM RX mode * @note Only allowed to be called when the channel state is REGISTERED, (i.e., channel has been allocated, but not initialized) * and the state will be updated to READY if initialization success, otherwise the state will return to REGISTERED. * * @param[in] handle I2S rx channel handler * @param[in] pdm_rx_cfg Configurations for PDM RX mode, including clock, slot and gpio * The clock configuration can be generated by the helper macro `I2S_PDM_RX_CLK_DEFAULT_CONFIG` * The slot configuration can be generated by the helper macro `I2S_PDM_RX_SLOT_DEFAULT_CONFIG` * * @return * - ESP_OK Initialize successfully * - ESP_ERR_NO_MEM No memory for storing the channel information * - ESP_ERR_INVALID_ARG NULL pointer or invalid configuration * - ESP_ERR_INVALID_STATE This channel is not registered */ esp_err_t i2s_channel_init_pdm_rx_mode(i2s_chan_handle_t handle, const i2s_pdm_rx_config_t *pdm_rx_cfg); /** * @brief Reconfigure the I2S clock for PDM RX mode * @note Only allowed to be called when the channel state is READY, i.e., channel has been initialized, but not started * this function won't change the state. 'i2s_channel_disable' should be called before calling this function if i2s has started. * @note The input channel handle has to be initialized to PDM RX mode, i.e., 'i2s_channel_init_pdm_rx_mode' has been called before reconfigring * * @param[in] handle I2S rx channel handler * @param[in] clk_cfg PDM RX mode clock configuration, can be generated by `I2S_PDM_RX_CLK_DEFAULT_CONFIG` * @return * - ESP_OK Set clock successfully * - ESP_ERR_INVALID_ARG NULL pointer, invalid configuration or not PDM mode * - ESP_ERR_INVALID_STATE This channel is not initialized or not stopped */ esp_err_t i2s_channel_reconfig_pdm_rx_clock(i2s_chan_handle_t handle, const i2s_pdm_rx_clk_config_t *clk_cfg); /** * @brief Reconfigure the I2S slot for PDM RX mode * @note Only allowed to be called when the channel state is READY, i.e., channel has been initialized, but not started * this function won't change the state. 'i2s_channel_disable' should be called before calling this function if i2s has started. * @note The input channel handle has to be initialized to PDM RX mode, i.e., 'i2s_channel_init_pdm_rx_mode' has been called before reconfigring * * @param[in] handle I2S rx channel handler * @param[in] slot_cfg PDM RX mode slot configuration, can be generated by `I2S_PDM_RX_SLOT_DEFAULT_CONFIG` * @return * - ESP_OK Set clock successfully * - ESP_ERR_NO_MEM No memory for DMA buffer * - ESP_ERR_INVALID_ARG NULL pointer, invalid configuration or not PDM mode * - ESP_ERR_INVALID_STATE This channel is not initialized or not stopped */ esp_err_t i2s_channel_reconfig_pdm_rx_slot(i2s_chan_handle_t handle, const i2s_pdm_rx_slot_config_t *slot_cfg); /** * @brief Reconfigure the I2S gpio for PDM RX mode * @note Only allowed to be called when the channel state is READY, i.e., channel has been initialized, but not started * this function won't change the state. 'i2s_channel_disable' should be called before calling this function if i2s has started. * @note The input channel handle has to be initialized to PDM RX mode, i.e., 'i2s_channel_init_pdm_rx_mode' has been called before reconfigring * * @param[in] handle I2S rx channel handler * @param[in] gpio_cfg PDM RX mode gpio configuration, specified by user * @return * - ESP_OK Set clock successfully * - ESP_ERR_INVALID_ARG NULL pointer, invalid configuration or not PDM mode * - ESP_ERR_INVALID_STATE This channel is not initialized or not stopped */ esp_err_t i2s_channel_reconfig_pdm_rx_gpio(i2s_chan_handle_t handle, const i2s_pdm_rx_gpio_config_t *gpio_cfg); #endif // SOC_I2S_SUPPORTS_PDM_RX #if SOC_I2S_SUPPORTS_PDM_TX #if SOC_I2S_HW_VERSION_2 /** * @brief PDM style in 2 slots(TX) * @param bits_per_sample i2s data bit width, only support 16 bits for PDM mode * @param mono_or_stereo I2S_SLOT_MODE_MONO or I2S_SLOT_MODE_STEREO */ #define I2S_PDM_TX_SLOT_DEFAULT_CONFIG(bits_per_sample, mono_or_stereo) { \ .data_bit_width = bits_per_sample, \ .slot_bit_width = I2S_SLOT_BIT_WIDTH_AUTO, \ .slot_mode = mono_or_stereo, \ .sd_prescale = 0, \ .sd_scale = I2S_PDM_SIG_SCALING_MUL_1, \ .hp_scale = I2S_PDM_SIG_SCALING_DIV_2, \ .lp_scale = I2S_PDM_SIG_SCALING_MUL_1, \ .sinc_scale = I2S_PDM_SIG_SCALING_MUL_1, \ .line_mode = I2S_PDM_TX_ONE_LINE_CODEC, \ .hp_en = true, \ .hp_cut_off_freq_hz = 35.5, \ .sd_dither = 0, \ .sd_dither2 = 1, \ } #else // SOC_I2S_HW_VERSION_2 /** * @brief PDM style in 2 slots(TX) * @param bits_per_sample i2s data bit width, only support 16 bits for PDM mode * @param mono_or_stereo I2S_SLOT_MODE_MONO or I2S_SLOT_MODE_STEREO */ #define I2S_PDM_TX_SLOT_DEFAULT_CONFIG(bits_per_sample, mono_or_stereo) { \ .data_bit_width = bits_per_sample, \ .slot_bit_width = I2S_SLOT_BIT_WIDTH_AUTO, \ .slot_mode = mono_or_stereo, \ .slot_mask = I2S_PDM_SLOT_BOTH, \ .sd_prescale = 0, \ .sd_scale = I2S_PDM_SIG_SCALING_MUL_1, \ .hp_scale = I2S_PDM_SIG_SCALING_MUL_1, \ .lp_scale = I2S_PDM_SIG_SCALING_MUL_1, \ .sinc_scale = I2S_PDM_SIG_SCALING_MUL_1, \ } #endif // SOC_I2S_HW_VERSION_2 /** * @brief i2s default pdm tx clock configuration * @note TX PDM can only be set to the following two up-sampling rate configurations: * 1: fp = 960, fs = sample_rate_hz / 100, in this case, Fpdm = 128*48000 * 2: fp = 960, fs = 480, in this case, Fpdm = 128*Fpcm = 128*sample_rate_hz * If the pdm receiver do not care the pdm serial clock, it's recommended set Fpdm = 128*48000. * Otherwise, the second configuration should be adopted. * @param rate sample rate */ #define I2S_PDM_TX_CLK_DEFAULT_CONFIG(rate) { \ .sample_rate_hz = rate, \ .clk_src = I2S_CLK_SRC_DEFAULT, \ .mclk_multiple = I2S_MCLK_MULTIPLE_256, \ .up_sample_fp = 960, \ .up_sample_fs = 480, \ } /* High Pass Filter Cut-off Frequency Sheet +----------------+------------------+----------------+------------------+----------------+------------------+ | param0, param5 | cut-off freq(Hz) | param0, param5 | cut-off freq(Hz) | param0, param5 | cut-off freq(Hz) | +----------------+------------------+----------------+------------------+----------------+------------------+ | (0, 0) | 185 | (3, 3) | 115 | (5, 5) | 69 | | (0, 1) | 172 | (1, 7) | 106 | (4, 7) | 63 | | (1, 1) | 160 | (2, 4) | 104 | (5, 6) | 58 | | (1, 2) | 150 | (4, 4) | 92 | (5, 7) | 49 | | (2, 2) | 137 | (2, 7) | 91.5 | (6, 6) | 46 | | (2, 3) | 126 | (4, 5) | 81 | (6, 7) | 35.5 | | (0, 3) | 120 | (3, 7) | 77.2 | (7, 7) | 23.3 | +----------------+------------------+----------------+------------------+----------------+------------------+ */ /** * @brief I2S slot configuration for pdm tx mode */ typedef struct { /* General fields */ i2s_data_bit_width_t data_bit_width; /*!< I2S sample data bit width (valid data bits per sample), only support 16 bits for PDM mode */ i2s_slot_bit_width_t slot_bit_width; /*!< I2S slot bit width (total bits per slot), only support 16 bits for PDM mode */ i2s_slot_mode_t slot_mode; /*!< Set mono or stereo mode with I2S_SLOT_MODE_MONO or I2S_SLOT_MODE_STEREO * For PDM TX mode, mono means the data buffer only contains one slot data, * Stereo means the data buffer contains two slots data */ /* Particular fields */ #if SOC_I2S_HW_VERSION_1 i2s_pdm_slot_mask_t slot_mask; /*!< Slot mask to choose left or right slot */ #endif uint32_t sd_prescale; /*!< Sigma-delta filter prescale */ i2s_pdm_sig_scale_t sd_scale; /*!< Sigma-delta filter scaling value */ i2s_pdm_sig_scale_t hp_scale; /*!< High pass filter scaling value */ i2s_pdm_sig_scale_t lp_scale; /*!< Low pass filter scaling value */ i2s_pdm_sig_scale_t sinc_scale; /*!< Sinc filter scaling value */ #if SOC_I2S_HW_VERSION_2 i2s_pdm_tx_line_mode_t line_mode; /*!< PDM TX line mode, on-line codec, one-line dac, two-line dac mode can be selected */ bool hp_en; /*!< High pass filter enable */ float hp_cut_off_freq_hz; /*!< High pass filter cut-off frequency, range 23.3Hz ~ 185Hz, see cut-off frequency sheet above */ uint32_t sd_dither; /*!< Sigma-delta filter dither */ uint32_t sd_dither2; /*!< Sigma-delta filter dither2 */ #endif // SOC_I2S_HW_VERSION_2 } i2s_pdm_tx_slot_config_t; /** * @brief I2S clock configuration for pdm tx mode */ typedef struct { /* General fields */ uint32_t sample_rate_hz; /*!< I2S sample rate */ i2s_clock_src_t clk_src; /*!< Choose clock source */ i2s_mclk_multiple_t mclk_multiple; /*!< The multiple of mclk to the sample rate */ /* Particular fields */ uint32_t up_sample_fp; /*!< Up-sampling param fp */ uint32_t up_sample_fs; /*!< Up-sampling param fs */ } i2s_pdm_tx_clk_config_t; /** * @brief I2S PDM tx mode GPIO pins configuration */ typedef struct { gpio_num_t clk; /*!< PDM clk pin, output */ gpio_num_t dout; /*!< DATA pin, output */ #if SOC_I2S_PDM_MAX_TX_LINES > 1 gpio_num_t dout2; /*!< The second data pin for the DAC dual-line mode, * only take effect when the line mode is `I2S_PDM_TX_TWO_LINE_DAC` */ #endif struct { uint32_t clk_inv: 1; /*!< Set 1 to invert the clk output */ } invert_flags; /*!< GPIO pin invert flags */ } i2s_pdm_tx_gpio_config_t; /** * @brief I2S PDM TX mode major configuration that including clock/slot/gpio configuration */ typedef struct { i2s_pdm_tx_clk_config_t clk_cfg; /*!< PDM TX clock configurations, can be genertated by macro I2S_PDM_TX_CLK_DEFAULT_CONFIG */ i2s_pdm_tx_slot_config_t slot_cfg; /*!< PDM TX slot configurations, can be genertated by macro I2S_PDM_TX_SLOT_DEFAULT_CONFIG */ i2s_pdm_tx_gpio_config_t gpio_cfg; /*!< PDM TX gpio configurations, specified by user */ } i2s_pdm_tx_config_t; /** * @brief Initialize i2s channel to PDM TX mode * @note Only allowed to be called when the channel state is REGISTERED, (i.e., channel has been allocated, but not initialized) * and the state will be updated to READY if initialization success, otherwise the state will return to REGISTERED. * * @param[in] handle I2S tx channel handler * @param[in] pdm_tx_cfg Configurations for PDM TX mode, including clock, slot and gpio * The clock configuration can be generated by the helper macro `I2S_PDM_TX_CLK_DEFAULT_CONFIG` * The slot configuration can be generated by the helper macro `I2S_PDM_TX_SLOT_DEFAULT_CONFIG` * * @return * - ESP_OK Initialize successfully * - ESP_ERR_NO_MEM No memory for storing the channel information * - ESP_ERR_INVALID_ARG NULL pointer or invalid configuration * - ESP_ERR_INVALID_STATE This channel is not registered */ esp_err_t i2s_channel_init_pdm_tx_mode(i2s_chan_handle_t handle, const i2s_pdm_tx_config_t *pdm_tx_cfg); /** * @brief Reconfigure the I2S clock for PDM TX mode * @note Only allowed to be called when the channel state is READY, i.e., channel has been initialized, but not started * this function won't change the state. 'i2s_channel_disable' should be called before calling this function if i2s has started. * @note The input channel handle has to be initialized to PDM TX mode, i.e., 'i2s_channel_init_pdm_tx_mode' has been called before reconfigring * * @param[in] handle I2S tx channel handler * @param[in] clk_cfg PDM TX mode clock configuration, can be generated by `I2S_PDM_TX_CLK_DEFAULT_CONFIG` * @return * - ESP_OK Set clock successfully * - ESP_ERR_INVALID_ARG NULL pointer, invalid configuration or not PDM mode * - ESP_ERR_INVALID_STATE This channel is not initialized or not stopped */ esp_err_t i2s_channel_reconfig_pdm_tx_clock(i2s_chan_handle_t handle, const i2s_pdm_tx_clk_config_t *clk_cfg); /** * @brief Reconfigure the I2S slot for PDM TX mode * @note Only allowed to be called when the channel state is READY, i.e., channel has been initialized, but not started * this function won't change the state. 'i2s_channel_disable' should be called before calling this function if i2s has started. * @note The input channel handle has to be initialized to PDM TX mode, i.e., 'i2s_channel_init_pdm_tx_mode' has been called before reconfigring * * @param[in] handle I2S tx channel handler * @param[in] slot_cfg PDM TX mode slot configuration, can be generated by `I2S_PDM_TX_SLOT_DEFAULT_CONFIG` * @return * - ESP_OK Set clock successfully * - ESP_ERR_NO_MEM No memory for DMA buffer * - ESP_ERR_INVALID_ARG NULL pointer, invalid configuration or not PDM mode * - ESP_ERR_INVALID_STATE This channel is not initialized or not stopped */ esp_err_t i2s_channel_reconfig_pdm_tx_slot(i2s_chan_handle_t handle, const i2s_pdm_tx_slot_config_t *slot_cfg); /** * @brief Reconfigure the I2S gpio for PDM TX mode * @note Only allowed to be called when the channel state is READY, i.e., channel has been initialized, but not started * this function won't change the state. 'i2s_channel_disable' should be called before calling this function if i2s has started. * @note The input channel handle has to be initialized to PDM TX mode, i.e., 'i2s_channel_init_pdm_tx_mode' has been called before reconfigring * * @param[in] handle I2S tx channel handler * @param[in] gpio_cfg PDM TX mode gpio configuration, specified by user * @return * - ESP_OK Set clock successfully * - ESP_ERR_INVALID_ARG NULL pointer, invalid configuration or not PDM mode * - ESP_ERR_INVALID_STATE This channel is not initialized or not stopped */ esp_err_t i2s_channel_reconfig_pdm_tx_gpio(i2s_chan_handle_t handle, const i2s_pdm_tx_gpio_config_t *gpio_cfg); #endif // SOC_I2S_SUPPORTS_PDM_TX #ifdef __cplusplus } #endif