Update for spelling etc. in comments!
This commit is contained in:
1 parent
aefcf5af63
commit
d506a3c49d
197 files changed
+1006
-757
No files matched your search
+9
-9
@@ -1,5 +1,5 @@
|
||||
// USER DEFINED SETTINGS
|
||||
// Set driver type, fonts to be loaded, pins used and SPI control method etc
|
||||
// Set driver type, fonts to be loaded, pins used and SPI control method etc.
|
||||
//
|
||||
// See the User_Setup_Select.h file if you wish to be able to define multiple
|
||||
// setups and then easily select which setup file is used by the compiler.
|
||||
@@ -28,15 +28,15 @@
|
||||
//#define NUCLEO_64_TFT
|
||||
//#define NUCLEO_144_TFT
|
||||
|
||||
// STM32 8 bit parallel only:
|
||||
// If STN32 Port A or B pins 0-7 are used for 8 bit parallel data bus bits 0-7
|
||||
// STM32 8-bit parallel only:
|
||||
// If STN32 Port A or B pins 0-7 are used for 8-bit parallel data bus bits 0-7
|
||||
// then this will improve rendering performance by a factor of ~8x
|
||||
//#define STM_PORTA_DATA_BUS
|
||||
//#define STM_PORTB_DATA_BUS
|
||||
|
||||
// Tell the library to use parallel mode (otherwise SPI is assumed)
|
||||
//#define TFT_PARALLEL_8_BIT
|
||||
//#defined TFT_PARALLEL_16_BIT // **** 16 bit parallel ONLY for RP2040 processor ****
|
||||
//#defined TFT_PARALLEL_16_BIT // **** 16-bit parallel ONLY for RP2040 processor ****
|
||||
|
||||
// Display type - only define if RPi display
|
||||
//#define RPI_DISPLAY_TYPE // 20MHz maximum SPI
|
||||
@@ -105,7 +105,7 @@
|
||||
// #define ST7735_GREENTAB3
|
||||
// #define ST7735_GREENTAB128 // For 128 x 128 display
|
||||
// #define ST7735_GREENTAB160x80 // For 160 x 80 display (BGR, inverted, 26 offset)
|
||||
// #define ST7735_ROBOTLCD // For some RobotLCD arduino shields (128x160, BGR, https://docs.arduino.cc/retired/getting-started-guides/TFT)
|
||||
// #define ST7735_ROBOTLCD // For some RobotLCD Arduino shields (128x160, BGR, https://docs.arduino.cc/retired/getting-started-guides/TFT)
|
||||
// #define ST7735_REDTAB
|
||||
// #define ST7735_BLACKTAB
|
||||
// #define ST7735_REDTAB160x80 // For 160 x 80 display with 24 pixel offset
|
||||
@@ -242,7 +242,7 @@
|
||||
|
||||
// ###### EDIT THE PINs BELOW TO SUIT YOUR ESP32 PARALLEL TFT SETUP ######
|
||||
|
||||
// The library supports 8 bit parallel TFTs with the ESP32, the pin
|
||||
// The library supports 8-bit parallel TFTs with the ESP32, the pin
|
||||
// selection below is compatible with ESP32 boards in UNO format.
|
||||
// Wemos D32 boards need to be modified, see diagram in Tools folder.
|
||||
// Only ILI9481 and ILI9341 based displays have been tested!
|
||||
@@ -250,7 +250,7 @@
|
||||
// Parallel bus is only supported for the STM32 and ESP32
|
||||
// Example below is for ESP32 Parallel interface with UNO displays
|
||||
|
||||
// Tell the library to use 8 bit parallel mode (otherwise SPI is assumed)
|
||||
// Tell the library to use 8-bit parallel mode (otherwise SPI is assumed)
|
||||
//#define TFT_PARALLEL_8_BIT
|
||||
|
||||
// The ESP32 and TFT the pins used for testing are:
|
||||
@@ -330,11 +330,11 @@
|
||||
// For RP2040 processor and SPI displays, uncomment the following line to use the PIO interface.
|
||||
//#define RP2040_PIO_SPI // Leave commented out to use standard RP2040 SPI port interface
|
||||
|
||||
// For RP2040 processor and 8 or 16 bit parallel displays:
|
||||
// For RP2040 processor and 8 or 16-bit parallel displays:
|
||||
// The parallel interface write cycle period is derived from a division of the CPU clock
|
||||
// speed so scales with the processor clock. This means that the divider ratio may need
|
||||
// to be increased when overclocking. It may also need to be adjusted dependant on the
|
||||
// display controller type (ILI94341, HX8357C etc). If RP2040_PIO_CLK_DIV is not defined
|
||||
// display controller type (ILI94341, HX8357C etc.). If RP2040_PIO_CLK_DIV is not defined
|
||||
// the library will set default values which may not suit your display.
|
||||
// The display controller data sheet will specify the minimum write cycle period. The
|
||||
// controllers often work reliably for shorter periods, however if the period is too short
|
||||
|
||||
Reference in new issue
Block a user