diff --git a/Packages_Patches/STM32/hardware/stm32/2.0.0/variants/STM32F7xx/F765Z(G-I)T_F767Z(G-I)T_F777ZIT/variant_NUCLEO_F767ZI.h b/Packages_Patches/STM32/hardware/stm32/2.0.0/variants/STM32F7xx/F765Z(G-I)T_F767Z(G-I)T_F777ZIT/variant_NUCLEO_F767ZI.h new file mode 100644 index 0000000..e8eaf79 --- /dev/null +++ b/Packages_Patches/STM32/hardware/stm32/2.0.0/variants/STM32F7xx/F765Z(G-I)T_F767Z(G-I)T_F777ZIT/variant_NUCLEO_F767ZI.h @@ -0,0 +1,274 @@ +/* + ******************************************************************************* + * Copyright (c) 2020-2021, STMicroelectronics + * All rights reserved. + * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ******************************************************************************* +*/ +#pragma once + +/*---------------------------------------------------------------------------- + * Pins + *----------------------------------------------------------------------------*/ + +#define PG9 0 +#define PG14 1 +#define PF15 2 +#define PE13 3 +#define PF14 4 +#define PE11 5 +#define PE9 6 +#define PF13 7 +#define PF12 8 +#define PD15 9 +#define PD14 10 +#define PA7 PIN_A10 +#define PA6 PIN_A11 +#define PA5 PIN_A12 +#define PB9 14 +#define PB8 15 +#define PC6 16 +#define PB15 17 +#define PB13 18 +#define PB12 19 +#define PA15 20 +#define PC7 21 +#define PB5 22 +#define PB3 23 +#define PA4 PIN_A13 +#define PB4 25 +#define PB6 26 +#define PB2 27 +#define PD13 28 +#define PD12 29 +#define PD11 30 +#define PE2 31 +#define PA0 PIN_A14 +#define PB0 PIN_A23 // LED_GREEN +#define PE0 34 +#define PB11 35 +#define PB10 36 +#define PE15 37 +#define PE14 38 +#define PE12 39 +#define PE10 40 +#define PE7 41 +#define PE8 42 +#define PC8 43 +#define PC9 44 +#define PC10 45 +#define PC11 46 +#define PC12 47 +#define PD2 48 +#define PG2 49 +#define PG3 50 +#define PD7 51 +#define PD6 52 +#define PD5 53 +#define PD4 54 +#define PD3 55 +// 56 is PE2 (31) +#define PE4 57 +#define PE5 58 +#define PE6 59 +#define PE3 60 +#define PF8 PIN_A15 +#define PF7 PIN_A16 +#define PF9 PIN_A17 +#define PG1 64 +#define PG0 65 +#define PD1 66 +#define PD0 67 +#define PF0 68 +#define PF1 69 +#define PF2 70 +// 71 is PA7 (11) +// 72 is NC +#define PB7 73 // LED_BLUE +#define PB14 74 // LED_RED +#define PC13 75 // USER_BTN +#define PD9 76 // Serial Rx +#define PD8 77 // Serial Tx +#define PA3 PIN_A0 +#define PC0 PIN_A1 +#define PC3 PIN_A2 +#define PF3 PIN_A3 +#define PF5 PIN_A4 +#define PF10 PIN_A5 +#define PB1 PIN_A6 +#define PC2 PIN_A7 +#define PF4 PIN_A8 +#define PF6 PIN_A9 +// ST Morpho +#define PA1 PIN_A18 +#define PA2 PIN_A19 +#define PA8 90 +#define PA9 91 +#define PA10 92 +#define PA11 93 +#define PA12 94 +#define PA13 95 // SWD +#define PA14 96 // SWD +#define PC1 PIN_A20 +#define PC4 PIN_A21 +#define PC5 PIN_A22 +#define PC14 100 +#define PC15 101 +#define PD10 102 +#define PE1 103 +#define PF11 104 +#define PG4 105 +#define PG5 106 +#define PG6 107 +#define PG7 108 +#define PG8 109 +#define PG10 110 +#define PG11 111 +#define PG12 112 +#define PG13 113 +#define PG15 114 +#define PH0 115 // MCO +#define PH1 116 + +// Alternate pins number +#define PA0_ALT1 (PA0 | ALT1) +#define PA0_ALT2 (PA0 | ALT2) +#define PA1_ALT1 (PA1 | ALT1) +#define PA1_ALT2 (PA1 | ALT2) +#define PA2_ALT1 (PA2 | ALT1) +#define PA2_ALT2 (PA2 | ALT2) +#define PA3_ALT1 (PA3 | ALT1) +#define PA3_ALT2 (PA3 | ALT2) +#define PA4_ALT1 (PA4 | ALT1) +#define PA5_ALT1 (PA5 | ALT1) +#define PA6_ALT1 (PA6 | ALT1) +#define PA7_ALT1 (PA7 | ALT1) +#define PA7_ALT2 (PA7 | ALT2) +#define PA7_ALT3 (PA7 | ALT3) +#define PA15_ALT1 (PA15 | ALT1) +#define PB0_ALT1 (PB0 | ALT1) +#define PB0_ALT2 (PB0 | ALT2) +#define PB1_ALT1 (PB1 | ALT1) +#define PB1_ALT2 (PB1 | ALT2) +#define PB3_ALT1 (PB3 | ALT1) +#define PB4_ALT1 (PB4 | ALT1) +#define PB5_ALT1 (PB5 | ALT1) +#define PB8_ALT1 (PB8 | ALT1) +#define PB9_ALT1 (PB9 | ALT1) +#define PB14_ALT1 (PB14 | ALT1) +#define PB14_ALT2 (PB14 | ALT2) +#define PB15_ALT1 (PB15 | ALT1) +#define PB15_ALT2 (PB15 | ALT2) +#define PC0_ALT1 (PC0 | ALT1) +#define PC0_ALT2 (PC0 | ALT2) +#define PC1_ALT1 (PC1 | ALT1) +#define PC1_ALT2 (PC1 | ALT2) +#define PC2_ALT1 (PC2 | ALT1) +#define PC2_ALT2 (PC2 | ALT2) +#define PC3_ALT1 (PC3 | ALT1) +#define PC3_ALT2 (PC3 | ALT2) +#define PC4_ALT1 (PC4 | ALT1) +#define PC5_ALT1 (PC5 | ALT1) +#define PC6_ALT1 (PC6 | ALT1) +#define PC7_ALT1 (PC7 | ALT1) +#define PC8_ALT1 (PC8 | ALT1) +#define PC9_ALT1 (PC9 | ALT1) +#define PC10_ALT1 (PC10 | ALT1) +#define PC11_ALT1 (PC11 | ALT1) + +// This must be a literal +#define NUM_DIGITAL_PINS 117 +// This must be a literal with a value less than or equal to to MAX_ANALOG_INPUTS +#define NUM_ANALOG_INPUTS 24 + +// On-board LED pin number +#ifndef LED_BUILTIN + #define LED_BUILTIN PB0 +#endif +#define LED_GREEN LED_BUILTIN +#define LED_BLUE PB7 +#define LED_RED PB14 + +// On-board user button +#ifndef USER_BTN + #define USER_BTN PC13 +#endif + +// Timer Definitions +// Use TIM6/TIM7 when possible as servo and tone don't need GPIO output pin +#ifndef TIMER_TONE + #define TIMER_TONE TIM6 +#endif +#ifndef TIMER_SERVO + #define TIMER_SERVO TIM7 +#endif + +// UART Definitions +#ifndef SERIAL_UART_INSTANCE + #define SERIAL_UART_INSTANCE 3 //Connected to ST-Link +#endif +// Serial pin used for console (ex: stlink) +// Rerquired by Firmata +#ifndef PIN_SERIAL_RX + #define PIN_SERIAL_RX PD9 +#endif +#ifndef PIN_SERIAL_TX + #define PIN_SERIAL_TX PD8 +#endif + +// Value of the External oscillator in Hz +#define HSE_VALUE 8000000U + +/* Extra HAL modules */ +#if !defined(HAL_DAC_MODULE_DISABLED) + #define HAL_DAC_MODULE_ENABLED +#endif +#if !defined(HAL_ETH_MODULE_DISABLED) + #define HAL_ETH_MODULE_ENABLED +#endif +#if !defined(HAL_QSPI_MODULE_DISABLED) + #define HAL_QSPI_MODULE_ENABLED +#endif +#if !defined(HAL_SD_MODULE_DISABLED) + #define HAL_SD_MODULE_ENABLED +#endif + +// Last Flash sector used for EEPROM emulation, address/sector depends on single/dual bank configuration. +// By default 2MB single bank +#define FLASH_BASE_ADDRESS 0x081C0000 +#define FLASH_DATA_SECTOR 11 + +/*---------------------------------------------------------------------------- + * Arduino objects - C++ only + *----------------------------------------------------------------------------*/ + +#ifdef __cplusplus + // These serial port names are intended to allow libraries and architecture-neutral + // sketches to automatically default to the correct port name for a particular type + // of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN, + // the first hardware serial port whose RX/TX pins are not dedicated to another use. + // + // SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor + // + // SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial + // + // SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library + // + // SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins. + // + // SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX + // pins are NOT connected to anything by default. + #ifndef SERIAL_PORT_MONITOR + #define SERIAL_PORT_MONITOR Serial + #endif + #ifndef SERIAL_PORT_HARDWARE + // KH mod to add Serial1, for ESP-AT + //#define SERIAL_PORT_HARDWARE Serial + #define SERIAL_PORT_HARDWARE Serial1 + #endif +#endif diff --git a/Packages_Patches/STM32/hardware/stm32/2.0.0/variants/STM32L0xx/L052R(6-8)T_L053R(6-8)T_L063R8T/variant_generic.h b/Packages_Patches/STM32/hardware/stm32/2.0.0/variants/STM32L0xx/L052R(6-8)T_L053R(6-8)T_L063R8T/variant_generic.h new file mode 100644 index 0000000..43ba241 --- /dev/null +++ b/Packages_Patches/STM32/hardware/stm32/2.0.0/variants/STM32L0xx/L052R(6-8)T_L053R(6-8)T_L063R8T/variant_generic.h @@ -0,0 +1,173 @@ +/* + ******************************************************************************* + * Copyright (c) 2020-2021, STMicroelectronics + * All rights reserved. + * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ******************************************************************************* + */ +#pragma once + +/*---------------------------------------------------------------------------- + * STM32 pins number + *----------------------------------------------------------------------------*/ +#define PA0 PIN_A0 +#define PA1 PIN_A1 +#define PA2 PIN_A2 +#define PA3 PIN_A3 +#define PA4 PIN_A4 +#define PA5 PIN_A5 +#define PA6 PIN_A6 +#define PA7 PIN_A7 +#define PA8 8 +#define PA9 9 +#define PA10 10 +#define PA11 11 +#define PA12 12 +#define PA13 13 +#define PA14 14 +#define PA15 15 +#define PB0 PIN_A8 +#define PB1 PIN_A9 +#define PB2 18 +#define PB3 19 +#define PB4 20 +#define PB5 21 +#define PB6 22 +#define PB7 23 +#define PB8 24 +#define PB9 25 +#define PB10 26 +#define PB11 27 +#define PB12 28 +#define PB13 29 +#define PB14 30 +#define PB15 31 +#define PC0 PIN_A10 +#define PC1 PIN_A11 +#define PC2 PIN_A12 +#define PC4 PIN_A13 +#define PC5 PIN_A14 +#define PC6 37 +#define PC7 38 +#define PC8 39 +#define PC9 40 +#define PC10 41 +#define PC11 42 +#define PC12 43 +#define PC13 44 +#define PC14 45 +#define PC15 46 +#define PD2 47 +#define PH0 48 +#define PH1 49 + +// Alternate pins number +#define PA2_ALT1 (PA2 | ALT1) +#define PA3_ALT1 (PA3 | ALT1) + +#define NUM_DIGITAL_PINS 50 +#define NUM_ANALOG_INPUTS 15 + +// On-board LED pin number +#ifndef LED_BUILTIN + #define LED_BUILTIN PNUM_NOT_DEFINED +#endif + +// On-board user button +#ifndef USER_BTN + #define USER_BTN PNUM_NOT_DEFINED +#endif + +// SPI definitions +#ifndef PIN_SPI_SS + #define PIN_SPI_SS PA4 +#endif +#ifndef PIN_SPI_SS1 + #define PIN_SPI_SS1 PA15 +#endif +#ifndef PIN_SPI_SS2 + #define PIN_SPI_SS2 PNUM_NOT_DEFINED +#endif +#ifndef PIN_SPI_SS3 + #define PIN_SPI_SS3 PNUM_NOT_DEFINED +#endif +#ifndef PIN_SPI_MOSI + #define PIN_SPI_MOSI PA7 +#endif +#ifndef PIN_SPI_MISO + #define PIN_SPI_MISO PA6 +#endif +#ifndef PIN_SPI_SCK + #define PIN_SPI_SCK PA5 +#endif + +// I2C definitions +#ifndef PIN_WIRE_SDA + #define PIN_WIRE_SDA PB7 +#endif +#ifndef PIN_WIRE_SCL + #define PIN_WIRE_SCL PB6 +#endif + +// Timer Definitions +// Use TIM6/TIM7 when possible as servo and tone don't need GPIO output pin +#ifndef TIMER_TONE + #define TIMER_TONE TIM6 +#endif +#ifndef TIMER_SERVO + #define TIMER_SERVO TIM21 +#endif + +// UART Definitions +#ifndef SERIAL_UART_INSTANCE + #define SERIAL_UART_INSTANCE 2 +#endif + +// Default pin used for generic 'Serial' instance +// Mandatory for Firmata +#ifndef PIN_SERIAL_RX + #define PIN_SERIAL_RX PA3 +#endif +#ifndef PIN_SERIAL_TX + #define PIN_SERIAL_TX PA2 +#endif + +// Extra HAL modules +#if !defined(HAL_DAC_MODULE_DISABLED) + #define HAL_DAC_MODULE_ENABLED +#endif + +/*---------------------------------------------------------------------------- + * Arduino objects - C++ only + *----------------------------------------------------------------------------*/ + +#ifdef __cplusplus + // These serial port names are intended to allow libraries and architecture-neutral + // sketches to automatically default to the correct port name for a particular type + // of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN, + // the first hardware serial port whose RX/TX pins are not dedicated to another use. + // + // SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor + // + // SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial + // + // SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library + // + // SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins. + // + // SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX + // pins are NOT connected to anything by default. + #ifndef SERIAL_PORT_MONITOR + #define SERIAL_PORT_MONITOR Serial + #endif + #ifndef SERIAL_PORT_HARDWARE + // KH mod to add Serial1, for ESP-AT + //#define SERIAL_PORT_HARDWARE Serial + #define SERIAL_PORT_HARDWARE Serial1 + #endif +#endif