Introduced in 97e3542947.
The previous commit frees the IRAM part when single core, but doesn't
change the memory layout functions. The unit test mallocs IRAM memory
from the heap, accidently into the new-released region, which doesn't
match the memory layout function.
This commit update the memory layout function to fix this.
Problem Decribe
The problem happenned when do wps with a mikrotik router
1. router always want to do connect with 32 without EAP-WSC step
2. after 4 way timeour, 32 crash
Root Cause
The reason why can not start EAP-WSC step is router's check method is RSN > WPA > WPS, when it found there include RSN and WPS in assoc, it will choice do 4 way rather than WPS
The reason of second problem is 32's EAPOL start timer didn't stop and send EAPOL start to a null pointer
Soultion
1. remove RSN and WPA ie when do WPS step
2. check mac address's pointer before send EAPOL start
closes: https://github.com/espressif/esp-idf/issues/2382
Fix following WiFi bugs:
1. Fix the bug that MIC verification fails on soft-AP mode
2. Modify mesh root to have same behavior as normal WiFi STA in state change
3. Fix the bug that sniffer can't catch control packets
4. Fix crash bug in soft-AP mode
5. Fix ACM(Admission Control Management) bug
1) two events AP_STOP, AP_START shortly after each other may cause IGMP config on already stopped netif
2) not properly locked sending packets to queue from timer task
closes#2580
Gitlab CI now allow us to define if a job need to be created by
varialbes. This commit add label to CI jobs, so we can make some jobs
not created in certain scenarios when we trigger pipeline with @bot.
Routine `spi_flash_cache2phys` sometimes return incorrect value,
resulting in failure in getting currently running ota partition.
This in turn aborts firmware update process.This issue was more
prominent with SPIRAM enabled cases.
Fix ensures proper cache guards during `spi_flash_cache2phys`, and
also for few other similar APIs.
In addition, `esp_ota_get_running_partition` has also been optimized
to save currently running partition for subsequent invocations.
Fixes https://github.com/espressif/esp-idf/issues/2451
In earlier change this component was decoupled from freertos and hence
regression was introduced which changed default placement to flash. Some
device drivers make use of ringbuffer while flash cache is being disabled
and hence default placement should instead be internal memory.
Closes: https://github.com/espressif/esp-idf/issues/2517
1. fix some bugs by previous coex hw blocking bugfix,
such like, rwble.c (64, 0) line 222
2. fix bug that ble scan performance is very low when software coexist
is working.
3. update libcoexist version to v1.1.0
Previous version assumed having winpty on the Path meant that it would be needed,
but some tools (like Atlassian Sourcetree) permanently add winpty to the path.
Symptom is arrow keys not working in menuconfig dialog.
Uninstaller is still unsigned, as currently building and signing in 'wine'
and running Linux osslsigncode inside Inno Setup inside wine is awkward.
Closes https://github.com/espressif/esp-idf/issues/1909
TW20810
This feature allows `httpd_req_recv()` and `httpd_send()` functions to return
specific `HTTPD_SOCK_ERR_` codes in case of socket errors. This is useful
in case of errors like `EAGAIN`, `EINTR`, etc. when the user may want to
retry `httpd_req_recv()` / `httpd_send()` function call.
This example adds functionality to support basic communication in RS485 networks using Modbus protocol.
This example uses FreeModbus stack and regular UART driver API to communicate in RS485 half duplex mode.
Added initial support of modbus controller pure C api to access device parameters over Modbus transport.
Move freemodbus stack and port files into components folder
Move the modbus_controller interface into components idf folder
Source files updated after review.
Add modbus interface documentation docs/en/api-reference/protocols/modbus.rst
porttimer.c: fix bug with timer1 selected in the Kconfig
Add support of cmake system (added cmake files)
Closes https://github.com/espressif/esp-idf/issues/858
In some cases, when data was just written into UART FIFO, transmitter
state could be still zero while the FIFO did contain some data.
This resulted in uart_tx_wait_idle occasionally returning before all
the data was sent out.
Fix by checking both UART transmitter state and TX FIFO count.
ROM definition of `abort` was removed in 9240bbb. The old definition
resulted in a panic due to a jump to a null pointer (abort member in
ROM stub table was zero). The new definition triggers a debug
exception if JTAG is connected, or goes into an infinite loop to be
reset by the WDT.
Some logging done in soc component may happen before logging via
stdout is possible. Use _EARLY version of log calls to make sure that
output is visible. The downside is that application does not have a
way to silence these logs. However since the soc component doesn’t
use any LOGV/LOGD/LOGI and only logs warnings and errors, this should
not impact the application.
This commit updates some of the API references in task.h so
that stack sizes are referred to in bytes rather than words as
found in the vanilla version.
Closes#2528
1. Fix the bug that ESP32 will reject the retry AddBA request frame
if AddBA response frame is failed to sent by WiFi LMAC
2. Fix the bug that AddBA request retrys too frequently
3. Forbid BA session setup for VO queue related TID
1. remove use EID to distinguish psram voltage
2. 1V8 64Mbit psram and 3V3 64Mbit psram use the same psram driver(standard spi interface)
3. set cs hold time register as 1
Content-Length header should not be included when using chunked encoding.
Some browsers will close the socket after seeing the 0 sized response instead of
reading the chunks.
Merges https://github.com/espressif/esp-idf/pull/2458
1. Add command for Ethernet based on console component.
2. Make cmd_system and iperf a component that can be referenced by other examples
3. Add "version" command to cmd_system.c
4. Clean up the README.md in all ethernet examples[TW#26525]
Added a new API esp_tls_set_global_ca_store(esp_tls_cfg_t *cfg) which creates a global_cacert which can be used by multiple connections by setting the use_global_ca_store variable to true in their respective structure of esp_tls_cfg_t. Also changed the cacert in the structure of esp_tls_t to a pointer.
* BLE and softAP provisioning examples added along with tests.
* An application specific example added for demonstrating custom provisioning scheme.
* tools/esp_prov/esp_prov.py can be used as a provisioning client for SoftAP, BLE and CLI based transports.
Co-Authored-By: Amey Inamdar <amey@espressif.com>
Co-Authored-By: Anurag Kar <anurag.kar@espressif.com>
* This manages secure sessions and provides framework for multiple transports.
* The application can use protocomm layer directly to have application specific extensions for provisioning (or non-provisioning) use cases.
* Following features are available for provisioning :
* Security - Security0 (no security), Security1 (curve25519 key exchange + AES-CTR encryption)
* Proof-of-possession support for Security1
* Protocomm requires specific protocol buffer modules for compilation which can be generated from the `.proto` files in the `proto` directory using make.
Co-Authored-By: Amey Inamdar <amey@espressif.com>
Co-Authored-By: Anurag Kar <anurag.kar@espressif.com>
tcp_transport component used public header files such as 'transport.h', etc. which are too generic and might collide with user or user libraries headers
This change closes#2417
In some cases, linker could choose to use ROM functions instead of the
ones defined in IDF.
For functions used in ROM stub table, this would lead to infinite
recursion when the corresponding function was called from ROM.
For crypto functions, some of these were modified in IDF, and
incompatible with ROM counterparts.
Problem Description
The reporduce steps are as follows:
1. put more than one same ssid AP in the environment;
2. set the STA mac address in one of the APs blacklist, and make sure the AP is closest to STA;
3. set the scan method in station config as all channel scan;
4. try to connect the AP which set STA in blacklist
Phenmenon
STA fail to connect after send auth or assoc with a wrong status code, but no disconnect event report and can not connect the next one in the envrionment
Root Cause
Because there are some same ssid APs in the evnrionment, when do all channel scan, it will collect all the matched AP in rc list, because rc list is not empty, so it would send disconnect event, however, we didn't do other step such as connect to other one
VNC MR 570
closes https://github.com/espressif/esp-idf/issues/2323
_rtc_data_{start,end} can now describe data placed into RTC_FAST
segment, if CONFIG_ESP32_RTCDATA_IN_FAST_MEM is enabled.
Use new _rtc_slow_length symbol instead.
When CONFIG_ESP32_RTCDATA_IN_FAST_MEM is enabled, RTC data is placed
into RTC_FAST memory region, viewed from the data bus. However the
bootloader was missing a check that this region should not be
overwritten after deep sleep, which caused .rtc.bss segment to loose
its contents after wakeup.
set shorter time to save some space on server. For those artifacts need
to be stored for long time, we can manually press "keep" button in job page.
Also add a CI job to check if all artifacts have set expire time.
fix the bug following:
1. after disable bluetooth controller, wifi cannot TX/RX any packets.
2. when software coexist working, there's a little ratio cause wifi task watchdog timeout
3. when software coexist working, there's a little ratio cause bluetooth cannot receive anything.
feature:
1. add libbtdm_app.a git commit local and remote checking
Known issues:
1. there's still a bug occurs with a very very low ratio cause bluetooth
cannot receive anything. The reproduce interval may great than 3days ~ 1week via
7x24 hours heavy testing.
Previously, esp-touch only supports multicast packets which are
transmitted from cellphone. But for most dual frequency routers
whose SSIDs of 5G and 2.4G are the same, broadcast packets are
forwarded from 5G interface to 2.4G interface while multicast
packets are not. In order to make esp-touch work when cellphone
connects to 5G interface of these routers, esp-touch is improved
to support both multicast and broadcast packets. Meanwhile, new
APP which is compiled with Andriod or IOS library(>= v0.3.6.2)
must be used in this situation. Note that for some routers,
broadcast and multicast packets are forwarded from 5G interface
to 2.4G interface only when another WiFi device is connected to
2.4G interface of the router. Old APP which is compiled with
Android or IOS library(< v0.3.6.2) also works with this improvement
when cellphone connects to 2.4G interface of the router.
The Android and IOS library of new esp-touch APP is now available
on Github.
Android: https://github.com/EspressifApp/EsptouchForAndroid
IOS: https://github.com/EspressifApp/EsptouchForIOS
Four internal APIs `esp_http_client_connect()`, `http_client_prepare_first_line()`, `esp_http_client_request_send()` and
`esp_http_client_send_post_data()` API have been added for perfoming connection establishment (sync as well as async),
preparing first line, sending request and sending post data respectively.
In `transport_ssl`, `ssl_connect_async()` API has been added for establishing asynchronous connection.
1. suppport mesh type, mesh ID, router and IE crypt func&key at any time after mesh is initalized.
2. support modify parent at any time after mesh is configured.
3. modify manual networking example.
4. update header file.
5. fix issues in root conflicts handling.
6. add max length of beacon to menuconfig.
7. fix issue when received a beacon without DSSS.
This introduces the following changes :
* Implmentation added for pthread attribute related functions :
* pthread_attr_init
* pthread_attr_destroy
* pthread_attr_setdetachstate
* pthread_attr_getdetachstate
* pthread_attr_getstacksize
* pthread_attr_setstacksize
* pthread_create now supports passing attributes/configs through pthread_attr_t structure
* pthread_mutex_timedlock added
* pthread_exit added
* memory for joinable thread is freed before returning from pthread_join
Problem Description
set some of routers as the same ssid in the same channel, when 32 in the fast scan connect mode, there may no disconnect event report in that two sceanrio:
1. set the correct password and connect, if target router didn't report 32's auth req before timeout, the state machine change to init but no disconnect event report
2. set a wrong password, if router send disassoc or deauth after run, rather than wait 4 way handshake timeout, the state machine change to init but no disconnect event report
Root Cause
Because the routers are in the same channel, all of them are matched the ssid, so all of them can be instore in the rc list wait for connect, when the first one want to connect fail at auth or receive
disassoc or deauth when password wrong, the rc list is not empty, it can not send disconnect event because rc is not empty
Solution
1. put the fail the router in the blacklist
2. Judge whether there is another router can be connect, if it has, try to connect with the next one
VNC MR 561
gen_esp_err_to_name.py includes files like
components/lwip/include/apps/esp_ping.h as "apps/esp_ping.h" because all
subdirectories of "include" are used. If "components/lwip/include/apps"
is in the path of the compiler instead of "components/lwip/include" then
include "apps/esp_ping.h" will fail. This fix allows to process lines
like:
'// gen_esp_err_to_name.py: some text "esp_ping.h" some text'
in header files for overwriting the include.
Before LwIP was moved into a submodule, sntp and esp_ping were
available as the following includes:
#include "apps/sntp/sntp.h"
#include "esp_ping.h"
This commit makes header files available at the old location, and adds
a deprecation warning for sntp.h.
Closes https://github.com/espressif/esp-idf/issues/2392
The lwip code didn't create an new mld group when netif is up,
this will lead to the server can't find the matching netif when
receiving NS(neighbor solicitation) packet
If exception support is disabled in IDF, and libstdc++ tries to throw
an exception, it will call __cxa_allocate_exception which is replaced
with abort in IDF.
We have a dramatically size reduction of the RO-section in binary when using '__throw_'-stubs in GCC5
In the case of using GCC8, we are faced with 'multiple definition' errors when using '__throw_'-stubs.
Good that we don't have the size problem due to gcc8
If CONFIG_FREERTOS_LEGACY_HOOKS is kept enabled then defining
idle/tick hooks will be applications responsibility as was the
case earlier.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
1. create a new pbuf to squash linked pbuf
2. optimize emac driver by adding ESP_IRAM_ATTR
3. remove duplicated function declare in esp_eth.h
4. remove duplicated code in emac_setup_tx_desc
5. disable Promiscuous mode
1. Keep awake to receive beacon at TBTT time no matter which state
station is on.
2. If there is any packet to send on dream or sleep state, send NULL
data with power save bit clear first.
This commit adds an option to enclose all FreeRTOS task functions within a
wrapper function. In the case that a task function returns, the wrapper function
will log an error and abort the application immediately.
Closes#2269Closes#2300
refence to https://github.com/espressif/esp-idf/issues/2284
Before fixing, the tx power in adv data is always 0xeb(-21dbm).
restriction:
If change BLE advertising TX power, please call esp_ble_gap_config_adv_data()
after BLE adv TX power changed.
Later, will implement set BLE advertising TX power via HCI, then the
TX power value in adv data can be update automatically after BLE adv
TX power changed.
Changes:
KConfig: The option CONFIG_ESP32_RTCDATA_IN_FAST_MEM is added in Kconfig file for esp32 component.
esp32.common.ld: added support of RTC_DATA_ATTR, RTC_RODATA_ATTR data placement into appropriate segment according to Kconfig option.
esp32.ld: linker script is modified to set alias for memory segment selected by Kconfig option to place data. The segments for force placement are added for RTC_FAST_ATTR, RTC_SLOW_ATTR attributes.
esp_attr.h: added new attributes RTC_FAST_ATTR, RTC_SLOW_ATTR for force placement into fest/slow memory.
test_rtc_fast.c: Added unit test cases to check data placement into appropriate memory segment.
Updated documentation for RTC_DATA_ATTR, RTC_FAST_ATTR, RTC_SLOW_ATTR in deep_sleep_stub.rst file.
TW#18001
Closes https://github.com/espressif/esp-idf/issues/1553
added docs and tests for mqtt library, small fixes (removed warnings, option for custom outbox, websocket bug fixed for longer transports). refactored to use common tcp_transport component, support for CMake build system.
Closes#2108
Allocation was happening later, causing possible use of stack variables
of caller function, which could be invalid.
Signed-off-by: Piyush Shah <piyush@espressif.com>
Using 'sudo pip install' can cause a lot of problems because usually
there are a couple of Python interpreters installed. This fix encourages
developers to use `pip install --user` instead which is safer.
On some systems pip and setuptools are no longer installed as
dependencies of the python packages. This commit adds the requirement
for these packages.
AVRCP connection binds to A2DP in current implementation, despite the two profiles are\
independent according to specification. AVRCP connection is not necessary to set-up \
if A2DP connection fails to establish
In opening state of AVDTP connection, if SDP client fails to get valid A2DP service record\
from peer SDP server, then do not initiate AVDTP connection request
In pevious implementation, A2DP sink will register an A2DP source Stream End Point(SEP) although the SEP is not\
supposed to be used. Now remove the unused SEP for source so that only one role of A2DP can be supported at one
time. Service record in local SDP server only includes at most one service for A2DP sink role or source
1. In original driver, the stack size for emac driver task "emacT" is only 2048 Bytes, which also can not be changed by user.
2. Each time when invoking "emac_start" function, it will reset emac registers, the driver should reconfig some important registers again.
* Fixed regex constraints for parsing IP and other parameters from monitor log.
* httplib connection timeouts set
* Redundent tests (commented out earlier) have been removed from advanced_tests. These tests are already run during unit testing.
Currently CI test environment is complicated, usually includes NIC, AP.
These devices are not used for a lot test cases. Therefore we split the
test environment, remove unnecessary devices. Then it will be easier to
create CI runners.
As the bluedroid original implmentation of BR/EDR and BLE dual mode about discovery mode,
when set discovery mode for BR/EDR, it will stop ble advertising.
Reference to https://github.com/espressif/esp-idf/issues/2306
The following commit rewrites the ESP-MESH docs. This commit includes
new diagrams and a structure approach to the mesh docs. Some mesh api references
have also been modified.
This commit does the following
- Add power management lock to CAN driver so that APB frequency does not change
whilst CAN driver is in use
- Fix incorrect flag in can_transmit()
- Refactor can_driver_install() and can_driver_uninstall() so that critical sections
are shorter
- Fix CAN gpio configuration bug on RX pin. Closes#2302
- Add docs about multiple ID configuration and fix example links
Problem:
The new API esp_bt_mem_release() that was added freed BTDM data to heap from esp_bt_controller_mem_release().
Now with the BT memory optimization commit ee787085f9,
the BTDM data is optimized and reduced to only 32 bytes which is not sufficient amount to be added to heap.
So, using the API leads to assert saying that the region is too small.
Solution:
Modify heap_caps_add_region_with_caps to return ESP_ERR_INVALID_SIZE in case the range is too small to create a new heap.
Do not assert if return value is ESP_ERR_INVALID_SIZE
This also fixes using API esp_bt_controller_mem_release() with ESP_BT_MODE_BTDM
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
Guarantees that a component's project_include.cmake will be called after its dependent components'
project_include.cmake. Because of cycles in the dependency graph, this is less useful than you'd
think but it gives a strong guarantee for any component which is not part of a cycle.
Also applies deterministic ordering (ordering is initialised as COMPONENT_REQUIRES_COMMON then all
COMPONENTS in alphabetical order, but then the sorting by dependencies is applied.)
Eclipse was unable to resolve the std::mutex type eventhough the mutex header file was succesfully included. By adding this modification, the issues was resolved.
Some APs transmit AMPDU and MPDU by turns. Moreover, the sequence
numbers of AMPDU and MPDU are out of order, e.g. MPDU(1253) -
AMPDU(1251, 1252) - MPDU(1254) - AMPDU(1255, 1256). In order to
receive both AMPDU and MPDU in order, MPDU must be reordered with
AMPDU.
1. New tests for SD card on slot 0. Currently frequency for 4-bit mode
has to be reduced in the test.
2. Change pin for CD/WP tests, re-enable CD tests.
Works for 3.3V eMMC in 4 line mode.
Not implemented:
- DDR mode for SD cards (UHS-I) also need voltage to be switched to 1.8V.
- 8-line DDR mode for eMMC to be implemented later.
This introduces the following changes in the example test scripts :
* Dependency on python requests library removed in favor of httplib
* Bug fixed in the logic responsible for receiving and processing http chunked responses
* Default timeouts increased Note : Due to connectivity issues (between runner host and DUT) in the runner environment, some of the advanced_tests are being ignored. These tests are intended for verifying the expected limits of the http_server capabilities, and implement sending and receiving of large HTTP packets and malformed requests, running multiple parallel sessions, etc. It is advised that all these tests be run locally, when making changes or adding new features to this component.
It is possible to utilize some of the routines related to otadata
partition validation, after firmware image is downloaded to RAM. Hence
these routines should be part of app cpu cache, so that they do not
get overwritten by firmware.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
Allows OTA updates to be secured via signature checks, without requiring the overhead or complexity
of a full secure boot implementation.
Uses same signing mechanisms (build system and/or espsecure.py as Secure Boot).
Requires:
* [ ] More testing
* [ ] Documentation
Fixes mismatches where default Python interpreter may not match the most recently
installed sphinx-build wrapper script (if sphinx 2 & 3 both installed, pip will
clobber any previous copy of /bin/sphinx-build when it installs the new one.)
res was declared as “bool” so expression
((count == 0) ? A2D_SET_ONE_BIT : A2D_SET_MULTL_BIT)
always evaluated to “true”, and was implicitly converted to
A2D_SET_ONE_BIT.
Avoids growing the result of hardware bignum operations
(particularly for multiplication)
Fixes bugs where some Elliptic Curve operations fail or corrupt memory,
as they assume length of the number is never greater than the number of
non-zero limbs.
Includes some general refactoring to standardize terminology.
Closes https://github.com/espressif/esp-idf/issues/1556
Fixes TW12984
Adds test cases for both these issues.
1. after memory release MR merged, due to the get acl number condition is not completed, it will cause get acl number value incorrect
2. It may cause set Security Mode (BR/EDR) enable failed
1. change static emac-dma memory to dynamic
2. add esp_eth_deinit
3. modify ethernet example
4. add testcase for ethernet deinit function
5. GPIO0 could not output the 50MHz clock to PHY, so remove this configuration
1. new APIs: esp_mesh_get_subnet_nodes_num() and esp_mesh_get_subnet_nodes_list().
2. fix hard to find the parent during connect.
3. disable Wi-Fi channel switch function.
4. fix a typo of MESH_EVENT_NO_PARENT_FOUND.
esp_reset_reason_init would check for reset reason hint, and
unconditionally set RTC_RESET_CAUSE_REG (which is also
RTC_ENTRY_ADDR_REG) to hint value 0, i.e. 0x80000000. However the ROM
code treats this value as valid deep sleep wake stub entry point, and
tries to jump to it.
Clear RTC_RESET_CAUSE_REG only if it contained a valid reset reason
hint, and simply set the register value to 0 when doing so. Also add
a check to esp_get_deep_sleep_wake_stub function that deep sleep wake
stub entry address must be in IRAM.
Reported in https://esp32.com/viewtopic.php?f=13&t=6919.
Fix following WiFi bugs:
1. Shouldn't scan when connect
2. Check beacon length in modem sleep
3. Fix the bug that AP may deauth wrong station when inactivity timer expires
4. Fix the bug that WiFi assert the system when receiving empty MCS in association response frame
Multiple modules register their callback BTA_GATTS_AppRegister().
If any of the callbacks do not free the allocated pointer in
BTA_GATTS_CONF_EVT event, then this can result in memory leak.
So, free the pointer after the callback function is called and remove
the calls to free in the callback functions as it is now not required
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
This is just a quick glance at all the header files exposed to the
users from cleanup point of view.
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
We have fixed a bug in test script. Before that, we didn't do strict check when generate the mesh tree, which makes the test pass.
Temp disable these cases, to let CI pass before bug fixed.
When 32k XTAL was selected as clock source, if the first calibration
attempt failed, the code would fall back to 150kHz internal clock.
Calibration with the internal clock will always succeed.
Therefore `wait` would always be either 0 or 1. Based on this, some
code in this routine can be eliminated.
Marking a page full does not skip it from page selection process and the
same page might get returned if there is no other page with more unused
entries. Added a check for the same while storing blobs.
Fixes: https://github.com/espressif/esp-idf/issues/2313
Previous APIs used to set CPU frequency used CPU frequencies listed in
rtc_cpu_freq_t enumeration. This was problematic for two reasons.
First, supporting many possible frequency values obtained by dividing
XTAL frequency was hard, as every value would have to be listed in
the enumeration. Since different base XTAL frequencies are supported,
this further complicated things, since not all of these divided
frequencies would be valid for any given XTAL frequency. Second,
having to deal with enumeration values often involved switch
statements to convert between enumeration and MHz values, handle
PLL/XTAL frequencies separately, etc.
This change introduces rtc_cpu_freq_config_t structure, which contains
CPU frequency (in MHz) and information on how this frequency has to
be generated: clock source (XTAL/PLL), source frequency, clock
divider value. More fields can be added to this structure in the
future. This structure simplifies many parts of the code, since both
frequency value and frequency generation settings can be accessed in
any place in code without the need for conversions.
Additionally, this change adds setting of REF_TICK dividers to support
frequencies lower then XTAL with DFS.
`esp_http_client_write` API puts a constraint on the maximum length of the data that can be
written, which is equal to client handle buffer size, but the data to be sent can be more
than that, so in this case, this API has to be called multiple times.
In `esp_http_client_open` API, the return value of `transport_write` API, used to send HTTP
request, is not checked, and in rare cases, data written will be less than expected which will
cause a problem. So there are fixes for these minor issues in this MR.
Calling `esp_bt_controller_mem_release` or `esp_bt_mem_release` might result in exception if any of the regions returned to heap are empty. This happens usually if BT/BLE is enabled, but not used/linked in the final firmware.
1. BLE only with 9(max) connection will decrease 3K DRAM
2. BR/EDR only with 7(max) connection will decrease 16K DRAM
3. Any of BLE or BR/EDR connection number decrease will also decrease DRAM consumption
4. Decrease one BLE connection will save about 1KB DRAM
5. Decrease one BR/EDR ACL connection will save about 1.2KB DRAM
6. Decrease one BR/EDR SCO/eSCO will save 2KB DRAM.
7. fix some definition and kconfig
8. remove 1.2k of vhci tx cache and make .bss & .data to heap about 1.4K
9. modify BT Reserved Memory size and modify example to support new bt kconfig
Hardware implements conditions LE, LT, GE, and conditions EQ and GT
are implemented in the assembler by emitting two JUMPS instructions
with other conditions.
Added bootloader_common_get_sha256_of_partition() and esp_partition_get_sha256() - get or calculate SHA-256
digest for app and data partitions.
Added bootloader_sha256_hex_to_str() - helps to print SHA-256 digest
Added esp_partition_check_identity() - compares two partitions by SHA-256 digest
Refactoring a function esp_image_load() in bootloader space to esp_image_verify() and
bootloader_load_image(). Old name function esp_image_load is deprecated
and will remove in V4.0 version.
spi_flash/sim: Fix error test_host. Add stub for bootloader_common_get_sha256_of_partition in sim/stubs
1. Add the 100 times test when the private key is generated by the random number;
2. Add the bt components to the unit-test-app/config directory.
3. Added the bt unit test case to CI.
For pins 32 and up the BIT(nr) macro used here overflowed,
causing undetermined GPIO pins to be reset.
Example: freeing SPI device/bus where CS is on pin 33
caused debug UART to cease communication, TXD0 was
disabled.
Fixed as BIT64(nr) macro, to be used elsewhere as needed.
For example in definitions like GPIO_SEL_32..GPIO_SEL_39.
1. modify parent switch mechanism.
2. fix non-root doesn't clear the layer value in nvs.
3. fix retransmit the remove announcement packets.
4. add API esp_mesh_flush_upstream_packets().
5. automatically adjust passsive scan time based on the change of beacon interval.
Component which includes component_ulp_common.mk may also need to set
some of the same COMPONENT_XXX variables. Logically, we should combine
the lists of files to embed, ldflags, extra include dirs, etc.
Fixes https://github.com/espressif/esp-idf/issues/2157.
The argument to ulp_run should be expressed in 32-bit words. Both the
address of ulp_entry and RTC_SLOW_MEM already are uint32_t*, so their
difference is the difference in addresses divided by sizeof(uint32_t).
Therefore the extra division by sizeof(uint32_t) is not needed.
1. The test step for error code REASON_ASSOC_EXPIRE is not reliable. SoftAP
could also send error code WIFI_REASON_NOT_AUTHED
2. STA will be disconnected now if softAP restart DHCP server
* "git clone" command and a small version header are generated
depending on git properties.
* Add Versions page with details about each version
* Make it clear using master branch is living on the "bleeding
edge"
No longer necessary to keep all reserved addresses in 'soc'.
Means 'soc' does not need to know about 'bt', for example.
Also means that Bluetooth can be enabled in config without any memory being reserved for BT
controller. Only if code calling the BT controller is linked in, will this memory be reserved...
This change adds a check for compatibility between the nvs version
found on nvs flash and the one assumed by running code during nvs
initialization. Any mismatch is reported to the user using new error
code ESP_ERR_NVS_NEW_VERSION_FOUND.
Update libphy.a to v3960:
1. Decrease phy_init time from 900us to 347us in sleep wakeup
2. Fix RX STBC initialization
3. Modify set_chan function to fix interrupt watchdog issue
it will resolve the problem:
1. when bluetooth is running (For example: a2dp sink), wifi station cannot connect to AP easily
2. improve wifi connection success ratio when coexist is working
Based on report on forum here:
https://esp32.com/viewtopic.php?f=13&t=6382&p=27514
Previous versions were much more relaxed about what could be in the partition
table, erroring out avoids unexpected changes on upgrade like different
partition offsets.
- A bug of the http client when it downloads a chunked encoding packet is greater than the http_client's buffer, http_parser will call the callback body more than once, and the client will only handle the last
- with ssl_read, need to check before read to avoid timeout blocked when no data for reading
* spi_flash_mmap_pages needs pages array to be in internal memory.
Document and check this.
* Fix a bug that spi_flash_mmap did not allocate pages array in
internal memory.
* Minor style fixes: const-ify pages argument of spi_flash_mmap, add
spaces around operators, mark output arguments with [out].
Closes https://github.com/espressif/esp-idf/issues/2229.
The test is previously disabled for the requirement of external
connection. Now the signals are connected by internal connections.
Also change the failure logic of the test.
Fixed problem with multiple mount/unmount for different devices.
Additional check for structure length included into the code.
Remove useless spaces.
Added initialization for reserved memory.
WL version 2 mark used sectors as 16 bytes block of bytes with CRC.
This changes required because old version did not worked with encryption.
Additional unit tests are implemented.
End handle is incorrectly printed as start handle
Tested that gatt_client, gatt_security_client and gattc_multi_connect compile successfully
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
Add a command `make erase_ota` - erases otadata if it there is in the
partition table otherwise error 'Partition table does not have ota_data partition'.
Closes https://github.com/espressif/esp-idf/issues/1821
heap_caps_malloc will fail to poison a block in IRAM with size not
divisible by 4. The proper fix will be to make poisoning code
smarter, or to disallow allocations from IRAM with size not aligned
by 4.
If project.mk is included twice in recursive invocation of Make, some
variables defined on the first pass will not be redefined on the
second pass. Rather than cleaning up these variables before calling
Make recursively, don’t include IDF project.mk at all, if one of the
ut- targets is requested.
If we have the partition table without any ota_apps but in ota_data have
valide entry, in this case we get an error(hang). This commit fix this
case. If bs->app_count is zero when selecting the factory app.
Closes https://github.com/espressif/esp-idf/issues/2218
1. when one task do deinit/init/disable/enable, especially different cpu
core, it may cause controller crash in ISR handler
2. fix while BLE is scanning, bluetooth controller is disabled cause BLE
scan is not abort.
1. Modify esp_bt_controller_mem_release() to release BTDM BSS and Data to heap if
ESP_BT_MODE_BTDM mode is passed to it
2. Add a new API esp_bt_mem_release() which internally calls
esp_bt_controller_mem_release() with the provided mode and then if mode
is ESP_BT_MODE_BTDM, releases BT BSS and Data to heap.
Background:
For Wi-Fi and BT/BLE applications, for e.g. the usecase is like when
Bluetooth is used for provisioning and once the device is connected to the Wi-Fi
AP, we can turn off Bluetooth completely. In such scenarios, it should be possible to
reclaim all the memory of Bluetooth. Although, currently this does not
happen.
Experiment:
Made the following modifications to examples/bluetooth/gatt_server :
1. Added support of simple_wifi to it
2. Moved all the bluetooth related code under CONFIG_BT_ENABLED config
option
3. Calculated the free heap in 2 similar scenarios:
i. Disabled BT (CONFIG_BT_ENABLED undefined) and checked the free
heap after STA connected
ii. Kept BT enabled and disabled it after STA connected and checked
the free heap
Ideally, the numbers for i., ii. above should have been similar. But
there was a delta of almost 30-31K. (i. > ii.)
4. Through make size-components checked the common BSS for libbta.a and libbtdm_app.a
and found it to be almost 30K. Data is around 1K
Solution:
1. Modified the linker script to mark the BSS and Data for these libraries and
free it when ESP_BT_MODE_BTDM mode is passed to mem release APIs.
2. Verified that the free heap is comparable for i. and ii. above.
Note: It is known that once this is done, Bluetooth can only be used
again post reboot.
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
This change removes the earlier limitation of 1984 bytes for storing data-blobs.
Blobs larger than the sector size are split and stored on multiple sectors.
For this purpose, two new datatypes (multi-page index and multi-page data) are
added for entries stored in the sectors. The underlying read, write, erase and find
operations are modified to support these large blobs. The change is transparent
to users of the library and no special APIs need to be used to store these large
blobs.
* Fixes some "noreturn" functions in bootloader utils which did return (causing fatal CPU
exceptions).
* Marks bootloader entry as "noreturn", preventing "user code done" from stalling boot
Partial fix for https://github.com/espressif/esp-idf/issues/1814 TW20016
(Comprehensive fix for this issue will be enabling WDT during bootloader, coming shortly.)
1. Move channel to the first row of the table.
2. Remove the condition of HT20/HT40 for they are determined by
secondary channel.
3. Clean up the CSI table.
Because address space is mapped in 64KB pages, it was possible for unauthenticated data after the
app .bin to become mapped into the flash cache address space.
This problem is solved by 2 changes:
* "esptool elf2image --secure-pad" will pad the image so that the signature block ends close to the
64KB boundary. Due to alignment constraints it will be 12 bytes too short after signing (but
with flash encryption, these 12 bytes are still encrypted as part of the last block and can't be
arbitrarily changed).
* By default, secure boot now requires all app partitions to be a multiple of 64KB in size.
- call rtc_gpio_init for pins which aren't configured as RTC by default
- for RTC IOs 16 and 17, read higher part of the input register
- automatically convert GPIO number into RTC IO number
- use ulp_set_wakeup_period instead of writing to register
We found some SD card on Raspberry Pi could have very bad performance.
It could take seconds to save small amount of data.
If the DUT receives data and save it as log, then it stops receiving data until log is saved.
This could lead to expect timeout. As an workaround to this issue,
``BaseDUT`` class will create a thread to save logs.
Then data will be passed to ``expect`` as soon as received.
Perviously host send_auto_stop flag would be set for every data
transfer over 1 block long. This caused stop commands to be sent
after CMD53, which shouldn't be done. Fix by adding an explicit list
of commands for which send_auto_stop should be set.
Send the Goodbye packet while removing an mDNS service as an "Authoritative" packet so
that the listeners remove the service from their records immediately.
Fixed the error division on zero.
Also fixed range CONFIG_ESP32_RTC_CLK_CAL_CYCLES in Kconfig.
Fixed a overflow error by TIMG in the function rtc_clk_cal_internal. This error was due to a limit in values TIMG_RTC_CALI_MAX=0x7FFF (to write the slowclk_cycles) and TIMG_RTC_CALI_VALUE=0x1FFFFFF (to read xtal_cycles). Added assert finctions.
Closes https://github.com/espressif/esp-idf/issues/2147
1. Add reading psram EID.
2. Configure different clock mode for different EID.
3. add API to get psram size and voltage.
4. Remove unnecessary VSPI claim.
For 32MBit@1.8V and 64MBit@3.3V psram, there should be 2 extra clock cycles after CS get high level.
For 64MBit@1.8 psram, we can just use standard SPI protocol to drive the psram. We also need to increase the HOLD time for CS in this case.
EID for psram:
32MBit 1.8v: 0x20
64MBit 1.8v: 0x26
64MBit 3.3v: 0x46
The WiFi station connect sequence diagram does not have any "successful" ending.
It looks like a copy-paste error, because there are two consequent `SYSTEM_EVENT_STA_DISCONNECTED` events firing with nothing happening in between.
I think the original meaning was that the last event should be `SYSTEM_EVENT_STA_CONNECTED` to signify that if all goes well, that is the event that will be fired.
Merges https://github.com/espressif/esp-idf/pull/2065
When 2nd stage bootloader loads the ROM bootloader, it prints a
message similar to "entry 0x40080xxx", which idf_monitor decodes
(using application ELF file) as one of the reset vectors (xxx is <
400h). This moves the iram_seg of bootloader 1k up to prevent overlap
of bootloader .text and application vectors, making the output look
nicer. There is still a chance that the entry point decodes as some
symbol in application ELF file, but at least it won't have
"Exception" in its name.
Since 94250e42a0, UART output is suspended when entering sleep mode
(deep or light sleep). This makes sense for light sleep, where sleep
normally takes small amount of time, and flushing the UART would add
a lot of latency. But this breaks existing behaviour for deep sleep,
where UART output was previously sent out before entering sleep mode.
Closes https://github.com/espressif/esp-idf/issues/2145
remote_ip was declared to be a pointer to an address that was
overwritten in later stage thus changing the address pointed by remote_ip
esp_smartconfig.h : Fixed a typo. station_config to wifi_config_t
Signed-off-by: Sachin Parekh <sachin.parekh@espressif.com>
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
uart.c/h: fix param errors
test_uart.c: Remove GCC warning supress
uart.rst: fix the notes
rs485_example.c: fix output
uart.c: remove reset using UART_RXFIFO_RST from driver.
readme.md: Update example description
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
uart.c/h: fix param errors
test_uart.c: Remove GCC warning supress
uart.rst: fix the notes
rs485_example.c: fix output
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
uart.c/h: fix param errors
test_uart.c: Remove GCC warning supress
uart.rst: fix the notes
rs485_example.c: fix output
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
components/wpa_supplicant/port/include/os.h:259:29: error: 'strncpy' output truncated before terminating nul copying 3 bytes from a string of the same length [-Werror=stringop-truncation]
#define os_strncpy(d, s, n) strncpy((d), (s), (n))
^~~~~~~~~~~~~~~~~~~~~~
components/wpa_supplicant/src/wpa2/eap_peer/eap.c:410:3: note: in expansion of macro 'os_strncpy'
os_strncpy(sm->blob[0].name, CLIENT_CERT_NAME, BLOB_NAME_LEN);
^~~~~~~~~~
components/spi_flash/partition.c: In function 'load_partitions':
components/spi_flash/partition.c:179:66: error: argument to 'sizeof' in 'strncpy' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
strncpy(item->info.label, (const char*) it->label, sizeof(it->label));
^
components/fatfs/src/ff.c: In function 'f_fdisk':
components/fatfs/src/ff.c:5995:5: error: this 'for' clause does not guard... [-Werror=misleading-indentation]
for (n = 16; n < 256 && sz_disk / n / cluster_size > 1024; n *= 2) ;
^~~
components/fatfs/src/ff.c:5996:2: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the 'for'
if (n == 256) n--;
^~
components/esp32/ipc.c: In function 'esp_ipc_init':
components/esp32/ipc.c:82:31: error: '%d' directive writing between 1 and 11 bytes into a region of size 5 [-Werror=format-overflow=]
sprintf(task_name,"ipc%d",i);
^~
components/esp32/ipc.c:82:27: note: directive argument in the range [-2147483648, 1]
sprintf(task_name,"ipc%d",i);
^~~~~~~
components/esp32/ipc.c:82:9: note: 'sprintf' output between 5 and 15 bytes into a destination of size 8
sprintf(task_name,"ipc%d",i);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
INTERRUPT and CCOUNT registers will change outside of program control.
Making the inline assembly used to read these registers volatile
indicates this fact to the compiler.
Fixes https://github.com/espressif/esp-idf/issues/2127
coap client parse a string by `coap_split_uri`,fetch host should by `host.length`
otherwise, would cause `gethostbyname` failed because of inappropriate parameter.
The fix is for the situation when cache disabling mechanism causes
a deadlock with user tasks. Situation is as follows:
1. spi_flash operation is started from low-priority task on CPU0
2. It uses IPC to wake up high-priority IPC1 task on CPU1, preventing
all other tasks on CPU1 from running. This is needed to safely
disable the cache.
3. While the task which started spi_flash operation is waiting for IPC1
task to acknowledge that CPU1 is not using cache anymore, it is
preempted by a higher priority application task ("app0").
4. Task app0 busy-waits for some operation on CPU1 to complete. But
since application tasks are blocked out by IPC1 task, this never
happens. Since app0 is busy-waiting, the task doing spi flash
operation never runs.
The more or less logical soltion to the problem would be to also do
cache disabling on CPU0 and the SPI flash operation itself from IPC0
task. However IPC0 task stack would need to be increased to allow doing
SPI flash operation (and IPC1 stack as well). This would waste some
memory. An alternative approach adopted in this fix is to call FreeRTOS
functions to temporary increase the priority of SPI flash operation task
to the same level as the IPC task.
Fixes https://github.com/espressif/arduino-esp32/issues/740
Fixes https://github.com/espressif/esp-idf/issues/1157
1. fix BLE connection missing in coex mode
2. modify other parameters to make coex priority more reasonable
3. fix modem sleep procedure trap cause Wifi disable RF when BT is
working. Such cause that BR/EDR is difficult to be connected, BLE
connection stability decrease and so on.
4. modify BR/EDR coexist duration to imrove BR/EDR connect success
ratio.
5. Due to the hardware coexist bug, BLE scan interval/window should
be less than 0x100(about 160ms). Therefore, it will cause BLE cannot
scan any advertising packet while WiFi have higher priority
behaviour(such like RX beacon, scan, TX/RX VO packets and etc.).
1. add APIs to set/get announce interval values.
2. add API to enable/disable the min rate to 6Mbps for data packages.
3. add APIs to set/get RSSI threshold values.
4. fix ap_loss.
Test report is not used as expected:
1. we rarely download and use test report
2. current test report method doesn't handle large amount data well,
need to be replaced by other methods
Test report also make test jobs allow to fail. It breaks the
original flow of Gitlab CI and make user confused.
Moved useful functions from wrapped assert functions, because option `CONFIG_OPTIMIZATION_ASSERTIONS_DISABLED=y` will remove this functions.
Closes https://github.com/espressif/esp-idf/issues/2068
1. esp_ble_remove_bond_device will only remove BLE bond key and disconnect BLE device.
2. esp_bt_gap_remove_bond_device will only remove BT bond key and disconnect BT device.
As reported https://esp32.com/viewtopic.php?f=14&t=6171
event_callback() in sockets.c calls conn->socket-- to register
activity on a netconn which may not have any socket yet,
so any socket value < 0 indicates "no controlling socket"
for the netconn.
51e42d8e92
introduced filtering options which handles the last (unterminated) line
with a delay. This introduced poor performance for console applications
when the user interacts with the ESP32 device in the same line because
there is an artificial delay for each key-press.
bb152030a0
decreased the delay but there are still delays for each key-presses.
The current fix makes only one delay per line instead of each
key-presses. When an unterminated line is detected then no more
"delayed" print is used for the given line.
Fixes https://github.com/espressif/esp-idf/issues/2054
IDF had two defines ESP_PARTITION_TABLE_OFFSET and ESP_PARTITION_TABLE_ADDR. They were the same and equal by 0x8000.
A define ESP_PARTITION_TABLE_ADDR was removed from IDF.
A define ESP_PARTITION_TABLE_OFFSET depends on option CONFIG_PARTITION_TABLE_OFFSET in Kconfig.
Now using only #define ESP_PARTITION_TABLE_OFFSET CONFIG_PARTITION_TABLE_OFFSET
This change allows readonly FATFS to be mounted without wear levelling
support. This will provide the customers a simple way to mount FATFS images
generated on host and flashed onto the chip during factory provisioning.
Since NVS encryption is not supported yet and NVS entry size is limited,
the change will provide an easy alternative for securing the provisioning data
by just marking FATFS parition as encrypted.
The IDF monitor waits for one second before printing the last
unterminated line. This is necessary for the correct filtering.
However, this causes poor performance, for example, in the case of the
system/console example.
This fix reduces the waiting time which improves the response time of
the console example and doesn't seem to influence the monitor filter.
Closes https://github.com/espressif/esp-idf/issues/2054
* a missing pointer increment caused error, if available was > 0 after the first iteration of while(available) loop.
* changed memory allocation strategy from large fixed size (RFCOMM_DATA_BUF_SIZE) to just the needed
size, which will be below MTU
Cherry-picked from https://github.com/espressif/esp-idf/pull/1923/
Since commit 94250e4, EXT0 wakeup mechanism, when wakeup level was set
to 0, started waking up chip immediately after entering deep sleep.
This failure was triggered in that commit by a change of
RTC_CNTL_MIN_SLP_VAL (i.e. minimum time in sleep mode until wakeup
can happen) from 128 cycles to 2 cycles.
The reason for this behaviour is related to the way input enable (IE)
signal going into an RTC pad is obtained:
PAD_IE = (SLP_SEL) ? SLP_IE & CHIP_SLEEP : IE,
where SLP_IE, SLP_SEL, and IE are bits of an RTC_IO register related
to the given pad. CHIP_SLEEP is the signal indicating that chip has
entered sleep mode.
The code in prepare_ext{0,1}_wakeup did not enable IE, but did enable
SLP_SEL and SLP_IE. This meant that until CHIP_SLEEP went high, PAD_IE
was 0, hence the input from the pad read 0 even if external signal
was 1. CHIP_SLEEP went high on the 2nd cycle of sleep. So when
RTC_CNTL_MIN_SLP_VAL was set to 2, the input signal from the pad was
latched as 0 at the moment when CHIP_SLEEP went high, causing EXT0
wakeup with level 0 to trigger.
This commit changes the way PAD_IE is enabled: SLP_SEL and SLP_IE are
no longer used, and IE is set to 1. If EXT0 wakeup is used, RTC_IO is
not powered down, so IE signal stays 1 both before CHIP_SLEEP goes
high and after. If EXT1 wakeup is used, RTC_IO may be powered down.
However prepare_ext1_wakeup enables Hold on the pad, locking states
of all the control signals, including IE.
Closes https://github.com/espressif/esp-idf/issues/1931
Closes https://github.com/espressif/esp-idf/issues/2043
For some test configurations, not all tests need to be run. This
change allows adding a comment in the configuration file of the
following form:
unit-test-app makefile will use it to determine which components to
build. If the comment is not present, all components will be built
(TESTS_ALL=1).
Also add test configuration for libsodium. It is a separate test
configuration due to the large binary size generated when building
libsodium tests.
Previously the loop in esp_timer_impl_set_alarm was necessary to catch
the case when timer count wraps around (goes from 2^32 - 1 to 0).
Since ALARM_OVERFLOW_VAL was reduced from 2^32 - 1 to 0xefffffff,
this is no longer necessary.
Fixes https://github.com/espressif/esp-idf/issues/1891
When ‘fetch’ strategy is used, Gitlab removes untracked files before
checking out new revision. However if the new revision doesn’t
include some of the submodules which were present in the old
revision, such submodule directories would not be removed by the
checkout. This extra step ensures that these stale submodules are
removed.
Allows you to move the partition table, it gives more space for the bootloader.
Added a new utility - parttool.py. This utility can search for the offset and/or size of the partitions by name and type/subtype. Use for getting APP_OFFSET and PHY_DATA_OFFSET.
The linker(esp32.bootloader.ld) made changes that allow you to write a custom bootloader code more.
TW14125
spi test: Prime the flash cache before each test to minimise flash cache misses.
VFS performance test: Increase the number of runs to minimise influence of an isolated bad run.
The old command caused was incorrect (x is “examine”, not “execute”)
and caused GDB register update only by chance. This replaces it with
“flushregs” command which purpose is exactly that — force GDB to
fetch registers from the remote.
Makes spiffs component runnable on host. Depends on the host library build
of flash emulator. Includes a basic sanity test of
mounting a volume, opening a file, writing to the file, reading the file,
closing the file and unmounting volume.
Makes fatfs component runnable on host. Depends on the host library build
of wear levelling and flash emulator. Includes a basic sanity test of
mounting a volume, opening a file, writing to the file, reading the file,
closing the file and unmounting volume.
Makes the entirety of the wl API runnable on host. Flash emulator
is separated into spi_flash component directory to be reused by
other storage components.
Before entering the deep sleep, the RTC and FRC counters are synchronized. Updating the boot_time.
Added a unit test for this case.
Fixed warnings for MULTIPLE_STAGES
Closes https://github.com/espressif/esp-idf/issues/1840
1. Fix the WiFi/BT coexist bug
2. Fix WPA2 enterprise example crash bug
3. Add size and version check for crypto type struct
4. Add MD5 check for crypto type header file
This fix is for compatibility with lwip_select(). It moves the lock to
UART which is the only VFS driver which is implemented and is not
"thread-safe".
These versions of conf/mconf are forked from the upstream, and the CMake system allows mconf-idf to
be installed externally on the path. So the best option is to rename.
Includes changes to Windows installer for v1.1
in the include file esp_ota_ops.h "esp_partition.h" is included.
This is from spi_flash so component that requires app_update also will need that
this fixes this error:
In file included from ../components/esp32-homie/ota.c:11:0:
/esp-idf/components/app_update/include/esp_ota_ops.h:22:27: fatal error: esp_partition.h: No such file or directory
Signed-off-by: Nicola Lunghi <25422924+nicola-lunghi@users.noreply.github.com>
Merges https://github.com/espressif/esp-idf/pull/1947
Don't show the "Python 2 interpreter" option in menuconfig when using CMake.
This is a stop-gap until we support Python 2 & 3 together in ESP-IDF (soon).
Closes https://github.com/espressif/esp-idf/issues/1924
This function speeds up or slows down the system clock in order to make a gradual adjustment. This ensures
that the calendar time reported by the system clock is always monotonically increasing, which might not happen
if you simply set the clock.
The delta argument specifies a relative adjustment to be made to the clock time. If negative, the system clock is
slowed down for a while until it has lost this much elapsed time. If positive, the system clock is speeded up for a
while.
If the olddelta argument is not a null pointer, the adjtime function returns information about any previous time
adjustment that has not yet completed.
The return value is 0 on success and -1 on failure.
To stop the adjustement, call the function settimeofday(current_time).
When using multiple sockets, some of them could be incorrectly removed
from the fd_sets before passing these fd_sets forward to the socket
select function.
Closes https://github.com/espressif/esp-idf/issues/1987
Added feature:
- reset firmware to Factory app.(by long pressing of the button)
- boot Test app. (by long pressing of the button)
- Added feature erase data partitions from factory reset.
TW10281
TW10280
Will give hint when any job failed to assign:
```
Please add the following jobs to .gitlab-ci.yml with specific tags:
* Add job with: psram, ESP32_IDF, UT_T1_1
* Add job with: psram, ESP32_IDF, UT_T1_1
```
We have built unit-test-app with different configs.
Currently we use the config name as tags to match runners.
It's not easy to add new configs (need to update tags to existed runners).
Now we'll parse required test runner tags from `sdkconfig` file.
For example, if config enables `CONFIG_SPIRAM_SUPPORT`, then it requires `psram` tag.
This will make adding new configs easier.
In this commit we change the one behavior of assign test: match keys of
cases should be exactly the same with job tags. This fixes cases select
jobs include their tags, and jobs requires those tags can't be assigned.
1. add mesh_assoc_t to esp_mesh_internal.h file.
2. rename "node" to "device" in esp_mesh.h.
3. add MESH_EVENT_SCAN_DONE event.
4. add APIs esp_mesh_scan_get_ap_record() and esp_mesh_scan_get_ap_ie_len() to get scan results.
5. modify API esp_mesh_set_self_organized() by adding parameter "select_parent".
6. modify API esp_mesh_set_parent() by adding parameter "parent_mesh_id"
7. add manual networking example.
1. Store the calibration data to NVS if PHY does full calibration because of calibration data checksum failure
2. Pass the station's mac to PHY for checksum calculation
This includes changing the picture of JTAG jumper block by removing the jumper on S_TDI. It has been reported by a number of users that removing this jumper fixes random communication issues observed in OpenOCD.
A new method of workaround an error with DPORT is to ensure that the APB is read and followed by the DPORT register without interruptions and pauses. This fix places this implementation in the IRAM to exclude errors associated with the cache miss.
Earlier they have to be selected at the compile time through sdkconfig.
A2DP sink and source application tested with this change.
Signed-off-by: Amey Inamdar <amey@espressif.com>
Add error handling for http client
set ssid password correct with Example_WIFI test, and clear password before free
Fixed the CI failure due to HTTP errror names
driver(i2c, rmt): Add xQueue and xSemaphore static allocation support when intr_alloc_flag set to ESP_INTR_FLAG_IRAM.
See merge request idf/esp-idf!2335
This fixes multiple bugs with ring buffers and re-factors the code. The public
API has not changed, however the underlying implementation have various private
functions have been changed. The following behavioral changes have been made
- Size of ring buffers for No-Split/Allow-Split buffers will not be rounded
up to the nearest 32-bit aligned size. This was done to simplify the
implementation
- Item size for No-Split/Allow-Split buffers will also be rounded up to the
nearest 32-bit aligned size.
The following bugs have been fixed
- In copyItemToRingbufAllowSplit(), when copying an item where the aligned
size is smaller than the remaining length, the function does not consider
the case where the true size of the item is less than 4 bytes.
- The copy functions will automatically wrap around the write pointers when
the remaining length of the buffer is not large enough to fit a header, but
does not consider if wrapping around will cause an overlap with the read
pointer. This will make a full buffer be mistaken for an empty buffer
closes#1711
- xRingbufferSend() can get stuck in a infinite loop when the size of the
free memory is larger than the needed_size, but too small to fit in the ring
buffer due to alignment and extra overhead of wrapping around.
closes#1846
- Fixed documentation with ring buffer queue set API
- Adding and removing from queue set does not consider the case where the
read/write semaphores actually hold a value.
The following functions have been deprecated
- xRingbufferIsNextItemWrapped() due to lack of thread safety
- xRingbufferAddToQueueSetWrite() and xRingbufferRemoveFromQueueSetWrite()
as adding the queue sets only work under receive operations.
The following functions have been added
- xRingbufferReceiveSplit() and xRingbufferReceiveSplitFromISR() as a thread
safe way to receive from allow-split buffers
- vRingbufferGetInfo()
Documentation for ring buffers has also been added.
Add function xRingbufferCanRead & xRingbufferCanWrite
to be able use queue sets. Without it is not possible
to check to which ringbuffer returned semaphore belongs.
1. provide options for bluetooth low power mode
2. provide two options for bluetooth low power clock: main XTAL and external 32kHz XTAL
3. provide function and callbacks to control bluetooth low power mode, including enable/disable sleep, software wakeup request, low power clock settings, check power state, etc
4. modify vhci API vhci_host_send_packet to use blocking mode
5. note that DFS and bluetooth modem sleep can not be used together currently.
In situations where idle task runs a lot of idle hooks or cleanup code
(due to pthread local storage, etc) it can use more than 1KB of stack.
(I think the trigger is if a context switch happens at the right point
in the TLS cleanup).
Also removes an sdkconfig.default which accidentally set all config items,
including this stack size.
Added .rtc_noinit and .noinit section definitions into linker file /esp32/ld/esp32.common.ld.
The macro __NOINIT_ATTR, RTC_NOINIT_ATTR declared in esp32/esp_attr.h file.
Added unit test file to test added behavior for noinit variables and its attributes.
Added documentation changes for new added attributes.
Make some corrections after code review:
The linker file has been corrected to place noinit section before bss_start to make it safer.
Documentation file has been modified to clarify reset behavior of allocated data .
Corrected typos in test_noinit.c and removed assertion of noinit variable to avoid possible issues with ROM boot loader memory allocation.
The linker file has been corrected to place noinit section before bss_start to make it safer.
Documentation file has been modified to clarify reset behavior of allocated data .
Corrected typos in test_noinit.c and removed assertion of noinit variable to avoid possible issues with ROM boot loader memory allocation.
Update test_noinit.c file to address RTCWDT_RTC_RESET reset reason instead of POWERON_RESET.
Test optimized to pass automated unit testing.
esp32: Add .noinit and .rtc_noinit sections to the linker script
Update of general-notes.rst documentation to fomat examples as code and attributes as identifiers.
Test test_noinit.c corrected to pass automated testing (support ofTEST_CASE_MULTIPLE_STAGES())
https://ezredmine.espressif.cn:8765/issues/15878
1. remove rc when ap not found
closes issue: https://github.com/espressif/esp-idf/issues/1797
2. allocate mimo packet to internal memory
3. use FRC2 timer instead of WDEV_NOW() for modem sleep to calculate
TBTT time.
It fixes the bug that TBTT will be incorrect if beacon is lost.
If the RTC crystal is bad or has no matched capacitance, then you do not need to start such the crystal. It is necessary to determine this case, output an error (about impossibility to start from the oscillator) and start from the internal RC of the chain.
Reduced the default value of the number of bootstrap cycles. Because we can oscillating the oscillator which then stops. (in Kconfig). Changed from 100 to 5.
The number of calibration cycles has been increased. It is the main criterion for estimating the launch of an oscillator. A large increase leads to an increase in the load time, as well as the stability of recognition of this case. (in Kconfig).
Changed from 1024 to 3000.
1. configs are not functional
* decorator will be executed when search case, need to set default config before search case.
2. fix DUT encode/decode errors
* python3 serial don't support write string/unicode, need to convert to bytes first.
* python2 string could failed to encode/decode non-acsii chars
3. fix bug that log folder not created
4. fix bug that test suite name is not correctly passed:
* the keyward arg should be `test_suite_name` not `test_name`
5. fix bug that test stopped on failed case
6. fix DUT `read` don't return all data cache
* `_DataCache.get_data` should first copy all data from queue to data cache and then return to user.
7. fix bug that `expect_all` failed even all expected item passed
8. optimize error info for expect
* print pattern for regular expression when match failed
9. fix bug that set default config doesn't work
1. Attenuator: control programmable attenuator
2. PowerControl: control APC PDU to power on/off devices
3. LineChart: use matplotlib to draw line chart
This fixes errors logged on the console: sdmmc_req:
handle_idle_state_events unhandled: 00000004 00000000
The issue happens if "data done" event occurs before "command done".
State machine code did not check *which* event occurred in
SENDING_CMD state, and went to IDLE or SENDING_DATA state on any
non-error event. In this case, we can't process "data done" event
until command has completed. This change introduces "unhandled event"
mask, which is carried over from one run of process_events to the
other. This allows waiting for the "command done" event to complete,
and then process "data done" event.
Ref TW17126.
CMD53 in byte mode supports transfers of any number of bytes between 1
and 512. This change removes limitation that the number of bytes must
be divisible by 4. Host quirk, that such transfers must be split into
two commands (one for the aligned part and the other one for
unaligned) is taken into account.
When two CPUs read the area of the DPORT and the area of the APB, the result is corrupted for the CPU that read the APB area.
And another CPU has valid data.
The method of eliminating this error.
Before reading the registers of the DPORT, make a preliminary reading of the APB register.
In this case, the joint access of the two CPUs to the registers of the APB and the DPORT is successful.
As of now, when Bluetooth debugs are enabled, all the messages are
mapped to BT_PRINTF which is mapped to ESP_LOGE. Hence, make monitor
shows all logs in red color which might lead to missing the actual
errors
This patch maps the Bluetooth messages to appropriate ESP_LOG* messages
and improves readability.
Also, make the BT trace level be configurable in menuconfig, so that
each layer of bt trace can be enabled/disabled.
Finally, add debug log control for BTC, OSI, BLUFI and clear up
Bluetooth debug logs.
So, with this the method of enabling Bluetooth logs is as follows:
1. make menuconfig -> Component config -> Bluetooth -> Bluedroid Enable
-> BT DEBUG LOG LEVEL -> set trace level for every layer of BT
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
If the allocated interrupt list is not empty and the new item will be inserted
as the header of the list, insert_vector_desc() causes crash because pre is
null. This commit fix this issue.
1. Fix the duty fade check issue reported from https://github.com/espressif/esp-idf/issues/1914
2. Fix the duty overflow issue when duty_scale is set to 1.
3. Fix the duty fade error when a fade operation is under way. We must configure a new duty setting after the previous fade operation has finished due to hardware limit.
4. Add thread-safe version APIs to set duty and fade.
5. Correct the duty range in driver.
It has been observed that, if external SPIRAM is enabled, then under
certain scenarios (e.g. internal memory being too much fragmented),
I2S tx/rx descriptors can land in external SPIRAM and hence resulting
in failure in DMA. Adding explicit capability to allocate in only DMA
capable memory.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
change some API function to throw event:
esp_wifi_deauth_sta
esp_wifi_get_country
esp_wifi_ap_get_sta_list
esp_wifi_sta_get_ap_info
esp_wifi_stop
esp_wifi_get_channel
esp_wifi_get_protocol
esp_wifi_get_bandwidth
ALT header files for sha1, sha256, sha512 are only supposed to declare
mbedtls_sha1_context data structure. Function prototypes should come
from original header files.
The following mbedTLS APIs have been deprecated and replaced with the
new ones which return error codes:
mbedtls_shaX_starts -> mbedtls_shaX_starts_ret
mbedtls_shaX_update -> mbedtls_shaX_update_ret
mbedtls_shaX_finish -> mbedtls_shaX_finish_ret
mbedtls_shaX_process -> mbedtls_shaX_internal_process
Update hardware implementations of SHA functions, and other IDF
components which used above functions, to use new versions.
When light sleep is started, the other CPU gets halted using DPORT
stall mechanism. This can happen while it is inside an esp_timer
critical section, which may lead to a deadlock. This change adds
functions to take and release esp_timer lock before entering
DPORT critical section, preventing the deadlock.
1. Add error log if failed to store calibration version/mac/data
2. Change the NVS calibration version/mac/data store sequence
3. Pass the init_data instead of NULL to esp_phy_rf_init() in esp_phy_load_cal_and_init()
Currently when page is being freed, items are individually moved from
FREEING page to ACTIVE page and erased. If power-off happens during the
process, the remaining entries are moved to ACTIVE page during recovery.
The problem with this approach is there may not be enough space on
ACTIVE page for all items if an item was partially written before
power-off and erased during recovery. This change moves all the items
from FREEING to ACTIVE page and then erased the FREEING page, If
power-off happens during the process, then ACTIVE page is erased and the
process is restarted.
Refactor IDF "project" functionality under a wrapping of the default
"project" command, so we can tweak it a bit...
Will need more testing in other environments.
* Philosophical: "explicit is better than implicit".
* Practical: Allows useful errors if invalid directories given in components as the defaults aren't
always used. Also trims the -I path from a number of components that have no actual include
directory.
* Simplifies knowing which components will be header-only and which won't
1. Change all the hash used from the coap module to generated by the bluedroid module directly.
component/bt: Added the <string.h> include file to the gattc_co module to avoid compile error.
component/bt: optimiz the code
component/bt: optimiz the code.
component/bt: added the l2c change.
component/bt: Added the modified.
component/bt: change the indicate callback function.
component/bt: added the BLE throughput test gattc & gatts example.
component/bt: Change the sdkconfig.default CONFIG_GATTS_NOTIFY_THROUGHPUT setting.
component/bt: Change the throughput_client_task delay method.
component/bt: change the btu task size from 4096 to 5096
comonent/bt: close the print when congest.
component/bt: Added the CPU frequency set method to the readme file.
component/bt: Change the gatts_demo_char1_val to gl_profile_tab[PROFILE_A_APP_ID].char_handle to avoid make error.
example/ble_throughput: Added the Readme explanation.
component/bt: Added the bt lib change.
component/bt: Update the bt lib & Change the LOG level from ERROR to DEBUG when congest.
component/bt: Fixed the bug of timer start assign error.
component/bt: Change back the gattc & gatts demo with same as the master.
example/ble_throughput: Fixed the bug when prepare write of the ble throughput.
component/bt: Update the check_sum algorithm.
component/bt: Change Added the path when used the include file of "l2cdefs.h" & "l2c_api.h".
example/throughput_client: Added the Freertos related header files to ble throughput client demo to avoid compile error.
1. add the L1 include path with a prefix, such like osi/list.h, stack/a2d_api.h and etc.
2. modify component, only bluedroid/api/include/api is export to another component and application,
other include path just for bluedroid used
3. put bluedroid/include into common/include/common, so the root directory of bluedroid have no include path.
4. modify doxygen to use esp_bt.h and redirect to
component/bt/bluedroid/api/include/api/
fix compile
Unit test runner expects to see the test name echoed after test
selection is made. If the unit test immediately goes into sleep mode,
UART output will not be complete, and test runner will not see the
test name. This flushes the stream buffer and waits for UART FIFO to
be empty before starting the test.
Additionally some parts of code used unity_printf and some used
printf. Since unity_printf was only useful during very early tests
when newlib was not available, replace all its usages with printf.
Disables app image integrity checks when running under OpenOCD control.
Allows setting breakpoints in flash before application start (just after reset).
Command response tokens can be delayed from the original command by 1
to 8 bytes. In 4a2489b9, handling for delayed tokens was added for
normal (no data) commands, and data read commands. This adds handling
for delayed commands for data write commands.
Currently when MAX_STATION limit in DHCP config is set to N, dhcp server
issues only N-1 IP addresses. This is problematic from customer
perspective if both SoftAP MAX_STATION and DHCP MAX_STATION limit is set
to same value. With this change DHCP server can issue N addresses that
is inline with the set limit.
Closes TW<20556>
Previous version of the code only connected CD and WP to the
peripheral, in fact the hardware does not use the values of these
signals automatically. This adds code to read CD and WP values when
command is executed and return errors if card is not present, or
write command is executed when WP signal is active.
Ideally suited for generating a binary externally, containing key-value pairs specific
to device manufacturers. Utility allows creation of a binary, compatible
with NVS structure, which can be separately flashed onto a new
partition. This helps device manufacturers set different values for
different devices, e.g. serial numbers, but using a single firmaware
image.
1. Bootloader reads SPI configuration from bin header, so that the burning configuration can be different with compiling configuration.
2. Psram mode init will overwrite original flash speed mode, so that users can change psram and flash speed after OTA. 3. Flash read mode(QIO/DIO…) will not be changed in app bin. It is decided by bootloader, OTA can not change this mode.
4. Add read flash ID function, and save flash ID in g_rom_flashchip
5. Set drive ability for all related GPIOs
6. Check raise VDDSDIO voltage in 80Mhz mode
7. Add check flash ID and update settings in bootloader
8. Read flash ID once and keep in global variable
9. Read flash image header once and reuse the result
Tested cases:
1. Test new and old version of bootloader
boot Flash 20M —> app Flash 80M + Psram 80M
boot Flash 40M —> app Flash 80M + Psram 80M
boot Flash 80M —> app Flash 80M + Psram 80M
boot Flash 20M —> app Flash 80M + Psram 40M
boot Flash 40M —> app Flash 80M + Psram 40M
boot Flash 80M —> app Flash 80M + Psram 40M
boot Flash 20M —> app Flash 40M + Psram 40M
boot Flash 40M —> app Flash 40M + Psram 40M
boot Flash 80M —> app Flash 40M + Psram 40M 2. Working after esp_restart reboot.
* Move smartconfig to its component directory, it should be possible to override
this as whole component
* Fix few header includes related to lwIP networking stack
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
If static task cleanup option is enabled, then before invoking application
defined `vPortCleanUpTCB` hook, pthread specific cleanup is performed.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
By default, any job will run unless a filter is given, in that case
the filter will determine if the job should run or not. Some jobs do
not need to be run by default, and should only be triggered using the
bot. For such jobs, BOT_NEEDS_TRIGGER_BY_NAME can added to
environment variables.
1. Change all the gattc API && bta gattc layer.
2. Debug the code and change the btc_ble_gattc_get_db method.
3. Change the gatt read API interface.
4. Reconstruction the BTA_gattc_cache code.
5. Change back the bluedroid_get_status to marco.
6. Change the gattc docs format.
7. Change the docs format.
8. fix the read char value bug.
9. change the gattc_get_attr_count method.
10. Change back the bta_gattc write ccc code.
11. Change the gattc api docs format
12. Change the gattc API docs.
13. Change the prepare write descriptor method to avoid the exection.
14. modify gatt clinet demo with new API
15. Change the p_src_data->read.p_value to avoid exection.
16. Change the bugfix of gattc unreg for the notify.
component/bt: Added the serch service res start_handle & end_handle to the result.
component/bt: Added the bta_gattc_cache_write when gatt discovery complete.
component/bt: Added the bta_gattc_cache_write declaration.
component/bt: Added the comments for esp_ble_gattc_cache_refresh API.
component/bt: Change the spelling errors & some comment error.
component/bt: fix bug of get gattc cache address list error.
1. Change the esp_bluedroid_get_status to macro;
2. added the malloc & free for the get_addr_list
component/bt: Added the addr_info->ass_addr == NULL Judgment to prevent crashes in the bta_gattc_co_cache_find_src_addr function.
component/bt: Fixed following gattc cache bugs
1. gattc can't refresh the gattc cache in the gatt discover state;
2. remove the nvs_get_blob in the cache address init function;
3. added the nvs_set_blob return value judgment in the cache address save function;
4. added the list_new when ass_address is NULL;
5. Change the ass_address list remove method to fix the ass address can't remove bug.
1. fix issues on sending beacon caused by too much tx retries on other packets.
2. modify not to scan if rc exists when connect.
3. modify scan dwell time to default 120ms fo root.
Need to make the bootloader modular so that users can redefine its functional part.
- refactoring and moving functions to the bootloader_support component
- Changed function to `void` bootloader_utility_load_image(...);
TW19596
Current code for recovery after power-off do not clean-up partially
erased items for FULL pages. If the erasure was part of modification
operation, this gets luckily cleaned-up because of duplicate detection
logic. For erase-only operation, the problem still exists. This patch
adds the recovery for FULL pages also.
Closes TW<20284>
With V=0, build process would print “including .../Makefile.projbuild" lines, causing problems for print_flash_cmd target.
The issue was due to the way macro expansion works in make. To delay evaluation of info function until the execution of expanded block, two dollar signs are required.
Test for print_flash_cmd target added.
When erasing a variable length item with an incorrect CRC32, the span
value of the item can not be trusted, so the item will be erased with
span = 1. Subsequent entries represent the data of the variable
length item, and these will be treated as separate items. For each
entry CRC32 is checked, the check most likely fails (because the
entry contains arbitrary data, and not a proper NVS item), and the
entry is erased. Erase function assumed that every item should be
present in cache, but it is not the case for the entries which are
just parts of item’s payload. This change allows for the item to be
not found in the hashlist, if the CRC32 check fails.
Currently for checking IDF version and submodules existence,
build system uses `git` commands. But, it could be possible use-case
where `git` is not installed (assuming IDF is flattened in source format)
on system and build happens without any warnings.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
Current page selection algorithm selects a page for compaction based on just erased counts
and gives up when it does not find any page with erased count greater than 0. This is
problematic since the current allocation procedure skips the active page if there is not
enough room for the item in that page leaving free chunks on the pages. This change modifies
the algorithm to consider both erased as well as free counts on the candidate pages.
Closes TW<20297>
Users needs functions to count the number of free and used entries.
1. `nvs_get_stats()` This function return structure of statistic about the uspace NVS.
(Struct: used_entries, free_entries, total_entries and namespace_count)
2. `nvs_get_used_entry_count()` The second function return amount of entries in the namespace (by handler)
3. Added unit tests.
Closes TW<12282>
1. fix a bug in initliazing map beacon interval.
2. fix not send MESH_EVENT_ROUTING_TABLE_REMOVE when MESH_NWK_CHILD_DISCONNECTED.
3. fix a bug in returning roots ie len.
Since !2190, source files located outside of the component root
produce object files inside build directory. This change fixes
handling of COMPONENT_OBJEXCLUDE variable for such files. Tests are
added.
- In SPI mode, the card will respond to the initial SDIO reset (done
using CMD52) with “invalid command” error. Handle this correctly.
- sdmmc_card_init had a hack where GO_IDLE_STATE (CMD0) command was
sent twice. Add explanation why this is done, and don’t expect
correct response from the card on first CMD0.
- improve logs printed at debug level by adding CMD index
- Split SDMMC page into pages about SDMMC/SDSPI hosts and a page about
the protocol layer.
- Use autogenerated API reference instead of manually generated one.
- Add information about SDIO APIs.
- Add SDIO support at protocol layer (probing, data transfer, interrupts)
- Add SDIO interrupts support in SDMMC host
- Add test (communicate with ESP32 in SDIO download mode)
Existing code assumed that response timeout is not followed by CMD_DONE,
which was not true, in fact. Host datasheet states that CMD_DONE is sent
after an RTO.
All the commands which do not have a response must have their flags set
accordingly. Therefore the host will not send RTO interrupt if response
is not expected. It is a bug in the code logic if it happens otherwise.
SDMMC host suffers from an issue that it outputs data near the rising
edge of the card clock, which is the edge used by the card to sample
data. If sampling time constraint is not satisfied, card may read data
after the transition.
The phases of output/input data can, in fact, be adjusted. However this
adjustment happens in the clock generation block outside of the host.
So the maximum phase change which can be created this way is equal to
half of the host clock period. So if the host clock is set to the lowest
possible frequency (for the given card frequency), then the phase offset
(and hence the hold time) will be the highest. This change modifies the
logic used to determine clock dividers accordingly.
sdmmc host: set correct dout phase and print correct frequency
SET_BUS_WIDTH is not a data transfer command. Extensive search in the
host datasheet and SD card spec did not reveal the origin of this hack
or 'feature'. Further testing showed that removing this does not lead to
regressions.
Fixes exceptions LoadProhibited, when rmt tries read variable p_rmt on RX END which can be 0.
It happens after esp_reset() (OTA) and the rmt is not probably stopped by it.
In other words the routine rmt_driver_isr_default was called before second rx channel was registered.
scenario:
register tx channel
register rx channel
reboot
register tx channel
-> exception (because rx channel is accessed)
Merges https://github.com/espressif/esp-idf/pull/1671
- In some cases where the HTTP URL contains the port number
(http://hostname:334), the DNS querier fails to resolve the hostname.
- Hence we have to populate the port number ourselves.
- This can only be done based on whether we get an IPv4 or IPv6
address.
Purpose:
1. TLS calls can be too many, and require a user to know the expected behaviour. A simple TLS socket wrapper that can be used in any higher level protocol.
2. Uses OpenSSL compatibility layer, so applications using esp-tls can be built on the host, and it should just work on ESP
Strips leading ../ when generating object file paths, keeps these in sync with the source files
otherwise.
This prevents object files landing in other directories, including outside the build directory, if
the component_srcdirs start with ../
When splitting a memory block, check if the next block is free.
If it is, then just extend it upwards instead of creating a new block.
This fixes a bug where when shrinking existing allocations would result in irreversible free space fragmentation.
When testing on the host, test all the poisoning configurations.
SDSPI driver optimized polling of the response tokens by requesting
two extra bytes on top of the block size (512) and CRC (2), and
checking whether these bytes contained the data response token or
not. In case the token was there, further polling would not need to
happen, thereby reducing latency between two consecutive blocks
transferred. However this caused compatibility issues when these two
extra bytes were sent after reading the final block. When
STOP_TRANSMISSION command was sent, these extra two bytes were
treated as part of the command, causing an invalid command error.
This fixes the logic by only requesting extra two bytes if the block
being read is not the final block. In addition to that, more strict
error checking is implemented for command response tokens.
The files updated according to code review discussions.
In the sleep_modes.c removed immidiate disable of ULP mode and leave just trigger deactivation.
The esp_sleep.h is updated to have the same defines for source as esp_sleep_wakeup_cause_t.
Updated documentation in sleep_modes.rst file to include cross references and address esp_sleep_wakeup_cause_t type.
The get_time_ms() is updated to explicitly use fabs(dt) instead of abs(dt) in test_sleep.c.
Some other minor changes in test_sleep.c unit test.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
Some application lock interrupt(portENTER_CRITICAL) too long time,
it will cause bluetooth cannot react interrupt in time, then t will
cause some assert, assert info following:
1. ld_acl.c 1900
2. ld_fm.c 340
3. other assert reference to this.
We had some problems:
simultaneous compiling of kconfig in the same tree;
attempt to use menuconfig in some examples and ut in batch mode (w/o interactive console)
Also increase debug abilities in CI:
force non-interactive building;
add variable DEBUG_SHELL to toggle verbosity of scripts
It is not possible to generate 1 MHz REF_TICK from 2 MHz APB clock
(this is a limitation of REF_TICK divider circuit). Since switching
REF_TICK frequency is something we would like to avoid (to maintain
UART output even with DFS), 2 MHz frequency has been marked as
unsupported.
The issue would manifest itself in cases when switching from PM
configuration like {active=160MHz, idle=80MHz} to {active=80MHz,
idle=80Mhz}. After the configuration was changed, PM logic would
think that current frequency was 80MHz and would not do any further
switching. In fact, frequency was still 160MHz.
The old code calculated MAX() of two enum values, but CPU frequency
enum values are not ordered (2MHz goes after 240MHz). This caused
incorrect configuration to be set.
Previous code contained a check for PLL frequency to be 240MHz, while
in fact 240MHz was a CPU frequency; corresponding PLL frequency is
480MHz. Fixed the comparison and replaced integer MHz values with an
enum.
This commit adds character encoding configurations in for the fatfs component.
The FF_LFN_UNICODE definition in ffconf.h can now be changed to accept UTF-8 or
UTF-16 encoded filernames. Test cases using UTF-8 encoded file paths and names in
FatFs have also been added.
Closes#1183
1. External 32kHz crystal is started for too long or it may not start at all. It is often observed at the first start.
2. At the first start, it is possible that the crystal did not start. And the recorded period was recorded as 0. Which led to a division error by zero during the transition to the deep sleep mode (Maybe somewhere else).
3. Added a unit test to test a new method of oscillation an external crystal.
4. Added a new method of oscillating of an external crystal. The legs of the crystal are fed with a 32 kHz frequency.
The new method eliminates these errors.
Added unit test: `\esp-idf\components\soc\esp32\test\test_rtc_clk.c`: `make TEST_COMPONENTS=soc`
- 8 Test starting external RTC crystal. Will pass.
`Bootstrap cycles for external 32kHz crystal` - is specified in the file Kconfig by default 100.
QA tested a new method of oscillation the crystal on 25 boards. The supply of square waves on the crystal showed a 100% result in contrast to the previous method of launching the crystal. After the tests, the old method was deleted.
Closes TW19143
The expected usage is:
esp_pthread_set_cfg(cfg);
pthread_create()
If the inherit flag is set, then all subsequent threads forked by this
thread will also inherit this configuration. This avoids having to
change/prefix this for each and every pthread_create() call.
Component/bt: fix reconnect fail in smp for v3.0
See merge request idf/esp-idf!2075
(cherry picked from commit 7f2a9f0359)
d0e55335 Component/bt: fix reconnect fail in smp
The fast path of CPU frequency switch function, used in DFS, was not
waiting for the frequency switch to complete when switching from XTAL
to PLL. This resulted in incorrect reads from peripherals on APB,
where two consecutive reads could return the same value. For example,
in esp_timer, read of FRC_COUNT_REG would return same value as the
preceding read of FRC_ALARM_REG, causing time to jump by the value of
FRC_ALARM_REG / apb_freq_mhz.
- separate mode stats from lock stats by an extra comment line
- add CPU frequency column to the mode stats
- don’t print a row for light sleep if light sleep is not enabled
s_cpu_freq_by_mode array was statically initialised with 80MHz CPU
frequency in CPU_MAX and APB_MAX modes, but sdkconfig setting for the
CPU frequency could have been different. For the case of 240MHz CPU
frequency, this would cause a frequency switch between 240MHz and
80MHz to happen, even though such switch is not supported in the fast
path switching functions used by the DFS implementation.
This fixes the issue by moving initialisation into esp_pm_impl_init,
which is called at startup before the first mode switch can happen.
Fixes https://github.com/espressif/esp-idf/issues/1729.
The files updated according to code review discussions.
In the sleep_modes.c removed immidiate disable of ULP mode and leave just trigger deactivation.
The esp_sleep.h is updated to have the same defines for source as esp_sleep_wakeup_cause_t.
Updated documentation in sleep_modes.rst file to include cross references and address esp_sleep_wakeup_cause_t type.
Some minor changes in test_sleep.c unit test.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
The files updated according to code review discussions.
In the sleep_modes.c removed immidiate disable of ULP mode and leave just trigger deactivation.
The esp_sleep.h is updated to have the same defines for source as esp_sleep_wakeup_cause_t.
Updated documentation in sleep_modes.rst file to include cross references.
Some minor changes in test_sleep.c unit test.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
On most microcontrollers I have worked with one can retrieve the
current state of output GPIO pins. On ESP32 this is not the case
if the pad is not explictly configured to route this information into
the port by configuring it as input or i/o.
Thus add a warning to the API documentation of gpio_get_level().
Merges https://github.com/espressif/esp-idf/pull/1740
Added function esp_sleep_disable_wakeup_source() to deactivate wakeup trigger for selected source.
Updated documentation for this function in sleep_modes.rst file.
Updated unit test to check this functionality for light sleep.
The test_sleep.c unit test is updated to add reliability for unit testing.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
The timer wakeup function once activated cannot be disabled later using existing api. If user wants to use different wakeup sources after first sleep but it does not work. This change disables timer wakeup trigger in configuration that will be set into appropriate RTC registers in esp_light_sleep_start() function.
Added function esp_sleep_disable_wakeup_source() to deactivate wakeup trigger for selected source.
Updated documentation for this function in sleep_modes.rst file to pass make html.
Updated unit test to check this functionality for light sleep.
The test_sleep.c unit test is updated to add reliability for auto unit testing.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
This commit fixes an incorrect register definition for BLK3_RESERVED_FLAG.
Other bugs include a missing conditional check, and updated comments
on modifying eFuse checking behavior.
On each documentation build (‘make html’), doxygen regenerates XML
files. In addition to that, gen-dxd.py regenerates API reference
files under _build/inc/. This results in Sphinx flagging about half
of the input files as modified, and incremental builds taking long
time.
With this change, XML files generated by Doxygen are copied into
docs/xml_in directory only when they are changed. Breathe is pointed
to docs/xml_in directory instead of docs/xml. In addition to that,
gen-dxd.py is modified to only write to the output file when contents
change.
Overall, incremental build time (with no source files changed) is
reduced from ~7 minutes to ~8 seconds (on a particular OS X
computer).
Due to the way Breathe includes Doxygen XML files, there is still
going to be a massive rebuild every time functions, enums, macros,
structures are added or removed from the header files scanned
by Doxygen, but at least individual .rst files can be edited
at a much faster pace.
This commit adds support for CPU max freqeuency rating
bits in CPU. Bootloader will now print an error if attempting
to 160MHz rated ESP32 at 240MHz.
EFUSE_CHIP_VER_RESERVE has been replaced by the
frequency rating bits. Dependancies on EFUSE_CHIP_VER_RESERVE
have been changed to use EFUSE_CHIP_VER_PKG
This commit removes the lookup table mode due to inferior performance when compared
to linear mode under attenuation 0, 1 and 2. However small portions of the lookup table
are kept for the higher voltages of atten 3 (above ADC reading 2880). That voltage range
in atten 3 has non linear characteristics making the LUT performan better than linear mode.
Add back a feature that was available in the old heap implementation
in release/v2.1 and earlier: keep track of which task allocates each
block from the heap. The task handle is conditionally added as
another word in the heap poisoning header under this configuration
option CONFIG_HEAP_TASK_TRACKING.
To allow custom monitoring and debugging code to be added, add helper
functions in multi_heap.c and multi_heap_poisoning.c to provide access
to information in the block headers.
Add esp_heap_debug_dump_totals() to monitor heap usage
esp_heap_debug_dump_totals() dumps into a user-provided data structure
a summary of the amound of heap memory in region type that is used by
each task. Optionally it will also dump into another data structure
the metadata about each allocated block for a given list of tasks or
for all tasks (limited by available space).
Address change requests on PR #1498
This set of changes fixes the files in e3b702c to just add the
CONFIG_HEAP_TASK_TRACKING option without adding the new function
heap_caps_get_per_task_info() in case that is the only portion of the
PR that will be accepted. Part of the change is to remove the new .c
and .h files containing that function and to remove the line to
compile it from components/heap/component.mk since it should not have
been included in e3b702c. One or more additional commits to add the
new function will follow.
The other changes here:
- uint32_t get_all_caps() moves to heap_private.h
- replace "void* foo" with "void *foo"
- add braces around single-line "if" blocks
- replace tab characters with spaces
Address change requests on PR #1498, part 2
This set of changes fixes the files in cdf32aa to add the new function
heap_caps_get_per_task_info() with its new name and to add the line to
compile it in components/heap/component.mk. This does not address all
the suggested changes because there are some needing further
discussion.
This commit does not include the suggested change to move the
declaration of the new function into esp_heap_caps.h because the new
function references TaskHandle_t so esp_heap_caps.h would have to
include freertos/FreeRTOS.h and freertos/task.h, but FreeRTOS.h
includes esp_heap_caps.h through two other header files which results
in compilation errors because not all of FreeRTOS.h has been read yet.
Change heap_caps_get_per_task_info() to take struct of params
In addition to moving the large number of function parameters into a
struct as the single parameter, the following changes were made:
- Clear out the totals for any prepopulated tasks so the app code
doesn't have to do it.
- Rather than partitioning the per-task totals into a predetermined
set of heap capabilities, take a list of <caps,mask> pairs to
compare the caps to the heap capabilities as masked. This lets the
caller configure the desired partitioning, or none.
- Allow the totals array pointer or the blocks array pointer to be
NULL to indicate not to collect that part of the information.
- In addition to returning the total space allocated by each task,
return the number of blocks allocated by each task.
- Don't need to return the heap capabilities as part of the details
for each block since the heap region (and therefore its
capabilities) can be determined from the block address.
- Renamed heap_task_info.h to esp_heap_task_info.h to fit the naming
convention, and renamed the structs for totals and block details to
better fit the revised function name.
- Provide full Doxygen commenting for the function and parameter
structs.
Add copyright header to new files
Merges https://github.com/espressif/esp-idf/pull/1498
Chapter Flash from Eclipse: Changed "Select Make Targets -> ..." to "Select Build Targets -> ..." to match the Eclipse wording. Same with "Project -> Make Target" replace Make by build to match the Eclipse wording.
tools/gen_esp_err_to_name.py generates
components/esp32/esp_err_to_name.c for lookup of the error codes from
all of the IDF project and easily identify all codes in one place
This commit updates the esp_adc_cal ocmponent to support new calibration methods
which utilize calibratoin values stored in eFuse. This commit includes LUT mode
At debug log level, tcpip_adapter would print logs for each function
call scheduled onto the tcpip task. These logs contained pointers which
idf_monitor decoded, adding even more noise and useless vertical space
in logs. This change moves these log statements to verbose level.
When realloc-ing to a smaller buffer size which ends up allocated in a different heap, the heap
structure is corrupted. This can only happen:
* If heap checking is Comprehensive (meaning buffers are never shrunk in place) and the heap the buffer was originally allocated in is full.
* Calling heap_caps_realloc() to deliberately move a buffer to a different capabilities type, and shrink it at the same time.
Probable fix for https://github.com/espressif/esp-idf/issues/1582
Probably the same issue:
https://www.esp32.com/viewtopic.php?f=2&t=4583https://www.esp32.com/viewtopic.php?f=13&t=3717
use performance matrix to tracking bin size is not convenient. bin size
do change for a lot reasons.
we'll implement a new method to track it. before that, set a large
enough threshold, so we can still keep tracking it.
The TRM describes IOMUX registers are IO_MUX_x_REG for x in GPIO0-39.
Until now ESP-IDF describes them as PERIPHS_IO_MUX_(pinname)_U
This commit adds additional IOMUX register names which match the ones used in the TRM.
1. Put some lwip udp rx/tx relating functions to IRAM
2. Put some wifi rx/tx relating functions to IRAMa
3. Reduce wifi dynamic malloc from 4 to 1 for each ebuf
4. Update iperf example accordingly
5. Update libphy.a to v383
Reported from github: https://github.com/espressif/esp-idf/issues/1236
All the touch channels are enabled by default in hardware. This would interfere other RTC function on Touch IOs.
Disable touch function in touch_pad_init().
function is called but NOT withe the same 'c' string constant that the LOG*
calls used in each module, the cache check doesn't match, so the cached
entry won't get updated. There's no point in optimizing this function
anyway because it is only called rarely.
Fix `#if (LOG_LOCAL_LEVEL >= ESP_LOG_INFO)` which is always false and
produces a warning with -Wundef.
Use same pattern to compare LOG_LOCAL_LEVEL with ESP_LOG_INFO as is used
in definition of `ESP_LOG_BUFFER_HEX_LEVEL` and
`ESP_LOG_BUFFER_CHAR_LEVEL`.
Also reformat existing definitions for better readability.
Closes https://github.com/espressif/esp-idf/issues/1526
Bluedroid use a set of timer function pairs such as btu_start_timer/btu_stop_timer, btu_sys_start_timer/btu_sys_stop_timer for use, in a lack of timer release functions. Thus the timers may be exhausted after some event sequence such as repetition of connection/reconnection with different devices. The maximum timer number used in bluedroid is given by ALARM_CBS_NUM which is 30 for now. This bugfix borrowed some update from bluedroid in Andoroid 7.0, which add timer release functions which promote the recycle of timer resources.
close github issue#1037 WiFi Promiscuous filter breaks w/
WIFI_PROMIS_FILTER_MASK_ALL and issue#1404
esp_wifi_set_promiscuous_filter set WIFI_PROMIS_FILTER_MASK_ALL error
component/bt: Added the Macro for the classic BT support.
component/bt: added the bluedroid deinit method.
component/bt: allow more classic BT global variables to use dynamic allocation scheme
1. allocate memory for AVDT, AVCT control blocks when dynamic memory is used
2. allow SBC decoder buffer to use dynamic allocation scheme
component/bt: Remove the wrong changes in bt/Kconfig & Added the GATTS_INCLUDED in the gatt_free function when gatt service close.
component/bt: Shorten the abbreviation BT_ALLOCATION_FROM_SPIRAM_FIRST and BT_BLE_DYNAMIC_ENV_MEMORY two macros.
requirement from github(https://github.com/espressif/esp-idf/issues/805): to provide the position in the buffer of the pattern detected.
requirement from AT application: in AT app, when no hardware flow control is enabled, in some situation the rx buffer might be full, and the terminator “+++” might be lost, we can use pattern detect interrupt to avoid missing the terminator. When pattern detect interrupt happens, it will not send a data event at the same time.
1. Add API to get position of detected pattern in rx buffer
2. Modify UART event example
3. Add comments for uart_flush, add alias API uart_flush_input to clear the rx buffer
4. Modify the way rx_buffered_len is calculated
Changes related to DFS have broken compilation of sysview code in 1 core
mode. This change fixes this, and moves choice of the timer used for
timestamp into Kconfig. CCOUNT timer is only available as an option if
1 core mode is used. esp_timer is added as a new option, and is the
only available option if DFS is enabled.
1. "lwip_socket" should close by "lwip_close_r" other than "lwip_close"
2. for generally compatible, fix all lwip interface to normally socket interface
3. call vTaskDelete when new socket failed in case of task crash
close #https://github.com/espressif/esp32-at/issues/58
1. remove the feature mask parameter from AVRC connection state event, as the AVCTP connection can be initiated by remote device before service discovery to remote device is performed. \
In this case, AVRCP connection state event may not be reported after connection initated by remote device is established.
2. remove ESP_AVRC_CT_MAX_EVT
3. add more documentations to AVRC APIs
When INT WDT fires, panicHandler is invoked. In OCD mode, panicHandler
sets a breakpoint on the PC from the exception frame and returns.
However in case of INT WDT, interrupt flag is still set in TIMERG1
peripheral, which causes INT WDT to trigger again. This causes an
endless stream of "Core 0 panic'ed (Interrupt wdt timeout on CPU1)"
messages. OpenOCD also gets terribly confused at this point.
Disable watchdogs when exiting panic handler in OCD mode.
Clear TIMERG1 WDT interrupt flag to prevent re-entry into panic handler.
RTC_FAST_CLK_FREQ_APPROX is defined as 8500000, so 0.5MHz part was lost
when dividing by MHZ. Since cal_val is 64-bit the parens can be removed.
With 40MHz XTAL for a nominal ESP32 chip, this fixes estimated XTAL
frequency from 38 to 40MHz.
In order for the Eclipse CDT GCC Build Output Parser to be able to
pick up the include paths for C++/cpp files a space is required
between the compiler option (-I) and the actual path.
Merges https://github.com/espressif/esp-idf/pull/1474
LOG_LOCAL_LEVEL is now used in a construct like:
#if (LOG_LOCAL_LEVEL >= ESP_LOG_INFO)
Make sure that LOG_LOCAL_LEVEL is defined, and don't use a type cast in
its definition, because preprocessor can not parse that.
1. ESP32 is found to suffer from AES encryption start/resume failure with specific device. Therefore temporarily disable BR/EDR Secure Connections for a workaround
2. BR/EDR Secure Connections is a feature for BT Classic introduced in Bluetooth 4.1. This change disables the setting of Secure Connections(Host Supported), and will result in the use of legacy authentication instead of secure authentication, and E0 encryption(legacy) instead of AES-CCM encryption. BLE security procedures are not affected.
Bugfix to prevent a self deleting no affinity task's memory from being freed by the
idle task of the other core before the self deleting no affinity task is able to context
switch out. prvCheckTasksWaitingTermination now checks if the task is still on
pxCurrentTCB before freeing task memory.
When tcp write/connect is running, close socket request will abort
it and continue to delete netconn and close tcp. Do not immediately
return after aborting tcp write/connect. Otherwise, tcp close
requeset will block and tcp write/connect will crash.
1. optimiz the ble stop adv callback function.
2. added the osi_mutex_unlock in the bta_gattc_wait4_service_change_ccc_cback function when the p_timer_param == NULL || p_conn == NULL.
1. fix the bug. Modify the condition that esp_bt_controller_mem_release() shoud be only called before esp_bt_controller_init() or after esp_bt_controller_deinit()
2. modify the example to use esp_bt_controller_mem_release()
libc time function now rely on esp_timer_get_time as the source of
high-resolution time, rather than FRC1 timer. Internally, on the ESP32
esp_timer implementation uses FRC2 timer.
- Change help text and labels in Kconfig to use "high-resolution timer"
instead of FRC1. Keep existing Kconfig option name to be backwards
compatible.
- Change references to "FRC1" in the source code to "FRC".
Replace explicit masks and shifts with bit fields when working with FATFS date and time representations. Also zero-initialize remaining members of struct tm.
Fixes https://github.com/espressif/esp-idf/issues/1369.
A couple of typos referencing tx_ring_buf when rx_ring_buf, slv_tx_mux
instead of slv_rx_mux.
Also, I2C_ENTER_CRITICAL()/I2C_EXIT_CRITICAL() usage was not consistent.
Only some of the _set_ functions had them. Most of the _get_ function
had them? It is my understanding that they should be wrapped around
writes, not reads? (I think we still need the lock for reading pairs of consistent values)
Also, the ticks_to_wait timeout handling in i2c_master_cmd_begin() would
not handle integer rollover correctly.
Merges https://github.com/espressif/esp-idf/pull/1180
Previously SDSPI host driver would rely on retry count when waiting for
the card to read or write data. This caused different timeout times
depending on CPU frequency and card clock frequency. In practice, card
performance does not depend on these two factors.
This change uses timeout_ms field of sdmmc_command_t introduced
previously for SDMMC host.
Fixes https://esp32.com/viewtopic.php?f=2&t=3440&p=16037 and similar
issues related to SDSPI timeouts.
FATFS does not support f_stat call for drive root. When handling stat
for drive root, don't call f_stat and just return struct st with S_IFDIR
flag set.
Closes#984
A function to change "in IRAM" status for an existing interrupt handle, without going through free/allocate of the interrupt.
mOS HW timer implementation requires this to make HW timers safe to re-set from an IRAM ISR.
This is a wrapper API for creating a Ring Buffer, which ensures that
the ringbuffer can hold the given number of items, each item being of the
same given length.
Signed-off-by: Piyush Shah <piyush@espressif.com>
Useful to check if the next item to receive is wrapped or not.
This is valid only if the ring buffer is initialised with type
RINGBUF_TYPE_ALLOWSPLIT.
This is as per the feature request here:
https://github.com/espressif/esp-idf/issues/806
Signed-off-by: Piyush Shah <piyush@espressif.com>
The earlier available API (xRingbufferGetMaxItemSize())just gives
a static max entry value possible for given ring buffer.
There was a feature request for an API which could provide
a real time available buffer size. See below:
https://github.com/espressif/esp-idf/issues/806
Signed-off-by: Piyush Shah <piyush@espressif.com>
current unit-test-app don't support test components need to communicate
with each other (like GPIO, SPI ...). Now we add multiple devices mode
to unit test app, support writing and running test with multiple DUTs.
please refer to `docs/api-guides/unit-tests.rst` for detail.
- Use `code` tags instead of a mix of `<pre></pre>` and
`@verbatim .. @endverbatim`
- Remove manually added function prototypes from comment blocks
- Remove of grouping (`\defgroup`) — some extra work is needed
to make groups compatible with the way we auto-generate API
reference from Doxygen XML files. It's pretty easy to add the
grouping directives back if/when we implement support for
Doxygen groups in the later stages of documentation build
process.
- Hide private APIs under `@cond .. @endcond`
- Convert some comments into Doxygen-compatible ones
- Fix various documentation issues: missing documentation for
some parameters, mismatch between parameter names in comment
block and in function prototype.
- Add doxygen comments for functions which didn't have them
(thread local storage).
- Add [out] param tags where necessary
- Redefine `xTaskCreate` and `xTaskCreateStatic` as inline
functions instead of macros.
When compiling
> const ulp_insn_t program[] = {
> I_DELAY(1)
> };
with the xtensa-esp32-elf-g++ compiler i always got the error:
> sorry, unimplemented: non-trivial designated initializers not supported
>
> };
This was due to the different order in the macro and the struct. The struct has another order of the fields (opcode, unused, cycles) vs (cycles, unused, opcode):
> struct {
> uint32_t cycles : 16; /*!< Number of cycles to sleep */
> uint32_t unused : 12; /*!< Unused */
> uint32_t opcode : 4; /*!< Opcode (OPCODE_DELAY) */
> } delay; /*!< Format of DELAY instruction */
After updating the order in the macro it is possible to compile with the g++ compiler.
Merges https://github.com/espressif/esp-idf/pull/1310
This commit backports vTaskDelete() behavior from FreeRTOS v9.0.0 which
allows for the immediate freeing of task memory if the task being deleted
is not currently running and not pinned to the other core. This commit also
fixes a bug in prvCheckTasksWaitingTermination which prevented the
Idle Task from cleaning up all tasks awaiting deletion. Each iteration of the Idle
Task should traverse the xTasksWaitingTermination list and clean up all tasks
not pinned to the other core. The previous implementation would cause
prvCheckTasksWaitingTermination to return when encountering a task
pinned to the other core whilst traversing the xTasksWaitingTermination list.
The test case for vTaskDelete() has been updated to test for the bugfix and
backported deletion behavior.
* Change snprintf for strlcat does not complain w/gcc7.2.0 and it is safer, thanks @projectgus
* Use proper quotes for character literals
Merges https://github.com/espressif/esp-idf/pull/1163
Reported from github:
https://github.com/espressif/esp-idf/issues/1312https://github.com/espressif/esp-idf/issues/1193
Issues:
1. We used to use event group in the driver, which would cause:
a. longer operation time since the event group are based on FreeRTOS timer.
b. Operation fails if the timer queue is not long enough.
2. There might be some issue with event group, we will still try to provide a small test code in other branch.
modification:
1. use queue instead of event-bit for internal commands
2. use queue overwrite for cmd_done event
@@ -25,6 +25,8 @@ Before sending us a Pull Request, please consider this list of points:
* Are comments and documentation written in clear English, with no spelling or grammar errors?
* Example contributions are also welcome. Please check the :doc:`creating-examples` guide for these.
* If the contribution contains multiple commits, are they grouped together into logical changes (one major change per pull request)? Are any commits with names like "fixed typo" `squashed into previous commits <http://eli.thegreenplace.net/2014/02/19/squashing-github-pull-requests-into-a-single-commit/>`_?
* If you're unsure about any of these points, please open the Pull Request anyhow and then ask us for feedback.
* [Getting Started Guide for the stable ESP-IDF version](https://docs.espressif.com/projects/esp-idf/en/stable/get-started/)
* [Getting Started Guide for the latest (master branch) ESP-IDF version](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/)
## Finding a Project
As well as the [esp-idf-template](https://github.com/espressif/esp-idf-template) project mentioned in the setup guide, ESP-IDF comes with some example projects in the [examples](examples) directory.
As well as the [esp-idf-template](https://github.com/espressif/esp-idf-template) project mentioned in Getting Started, ESP-IDF comes with some example projects in the [examples](examples) directory.
Once you've found the project you want to work with, change to its directory and you can configure and build it.
To start your own project based on an example, copy the example project directory outside of the ESP-IDF directory.
# Quick Reference
See the Getting Started guide links above for a detailed setup guide. This is a quick reference for common commands when working with ESP-IDF projects:
## Configuring the Project
`make menuconfig`
@@ -36,15 +41,17 @@ Once done configuring, press Escape multiple times to exit and say "Yes" to save
## Compiling the Project
`make all`
`make -j4 all`
... will compile app, bootloader and generate a partition table based on the config.
NOTE: The `-j4` option causes `make` to run 4 parallel jobs. This is much faster than the default single job. The recommended number to pass to this option is `-j(number of CPUs + 1)`.
## Flashing the Project
When `make all` finishes, it will print a command line to use esptool.py to flash the chip. However you can also do this from make by running:
When the build finishes, it will print a command line to use esptool.py to flash the chip. However you can also do this automatically by running:
`make flash`
`make -j4 flash`
This will flash the entire project (app, bootloader and partition table) to a new chip. The settings for serial port flashing can be configured with `make menuconfig`.
@@ -52,28 +59,28 @@ You don't need to run `make all` before running `make flash`, `make flash` will
## Viewing Serial Output
The `make monitor` target uses the [idf_monitor tool](https://esp-idf.readthedocs.io/en/latest/get-started/idf-monitor.html) to display serial output from the ESP32. idf_monitor also has a range of features to decode crash output and interact with the device. [Check the documentation page for details](https://esp-idf.readthedocs.io/en/latest/get-started/idf-monitor.html).
The `make monitor` target uses the [idf_monitor tool](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/idf-monitor.html) to display serial output from the ESP32. idf_monitor also has a range of features to decode crash output and interact with the device. [Check the documentation page for details](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/idf-monitor.html).
Exit the monitor by typing Ctrl-].
To flash and monitor output in one pass, you can run:
To build, flash and monitor output in one pass, you can run:
`make flash monitor`
`make -j4 flash monitor`
## Compiling & Flashing Just the App
## Compiling & Flashing Only the App
After the initial flash, you may just want to build and flash just your app, not the bootloader and partition table:
*`make app` - build just the app.
*`make app-flash` - flash just the app.
`make app-flash` will automatically rebuild the app if it needs it.
`make app-flash` will automatically rebuild the app if any source files have changed.
(In normal development there's no downside to reflashing the bootloader and partition table each time, if they haven't changed.)
## Parallel Builds
ESP-IDF supports compiling multiple files in parallel, so all of the above commands can be run as `make -jN` where `N` is the number of parallel make processes to run (generally N should be equal to or one more than the number of CPU cores in your system.)
ESP-IDF supports compiling multiple files in parallel, so all of the above commands can be run as `make -jN` where `N` is the number of parallel make processes to run (generally N should be equal to the number of CPU cores in your system, plus one.)
Multiple make functions can be combined into one. For example: to build the app & bootloader using 5 jobs in parallel, then flash everything, and then display serial output from the ESP32 run:
@@ -81,6 +88,7 @@ Multiple make functions can be combined into one. For example: to build the app
make -j5 flash monitor
```
## The Partition Table
Once you've compiled your project, the "build" directory will contain a binary file with a name like "my_app.bin". This is an ESP32 image binary that can be loaded by the bootloader.
@@ -96,7 +104,7 @@ The simplest way to use the partition table is to `make menuconfig` and choose o
In both cases the factory app is flashed at offset 0x10000. If you `make partition_table` then it will print a summary of the partition table.
For more details about partition tables and how to create custom variations, view the [`docs/api-guides/partition-tables.rst`](docs/api-guides/partition-tables.rst) file.
For more details about partition tables and how to create custom variations, view the [`docs/en/api-guides/partition-tables.rst`](docs/en/api-guides/partition-tables.rst) file.
## Erasing Flash
@@ -106,12 +114,12 @@ This can be combined with other targets, ie `make erase_flash flash` will erase
# Resources
* Documentation for the latest version: https://esp-idf.readthedocs.io/. This documentation is built from the [docs directory](docs) of this repository.
* Documentation for the latest version: https://docs.espressif.com/projects/esp-idf/. This documentation is built from the [docs directory](docs) of this repository.
* The [esp32.com forum](https://esp32.com/) is a place to ask questions and find community resources.
* [Check the Issues section on github](https://github.com/espressif/esp-idf/issues) if you find a bug or have a feature request. Please check existing Issues before opening a new one.
* If you're interested in contributing to ESP-IDF, please check the [Contributions Guide](https://esp-idf.readthedocs.io/en/latest/contribute/index.html).
* If you're interested in contributing to ESP-IDF, please check the [Contributions Guide](https://docs.espressif.com/projects/esp-idf/en/latest/contribute/index.html).
#define SEGGER_SYSVIEW_ID_BASE 0x3F400000 // Default value for the lowest Id reported by the application. Can be overridden by the application via SEGGER_SYSVIEW_SetRAMBase(). (i.e. 0x20000000 when all Ids are an address in this RAM)
#define SEGGER_SYSVIEW_ID_SHIFT 0 // Number of bits to shift the Id to save bandwidth. (i.e. 2 when Ids are 4 byte aligned)
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() ((*(U32 *)(0xE000ED04)) & 0x1FF) // Get the currently active interrupt Id. (i.e. read Cortex-M ICSR[8:0] = active vector)
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() (__get_IPSR()) // Workaround for IAR, which might do a byte-access to 0xE000ED04. Read IPSR instead.
#else
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() ((*(U32 *)(0xE000ED04)) & 0x3F) // Get the currently active interrupt Id. (i.e. read Cortex-M ICSR[5:0] = active vector)
#endif
#else
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() SEGGER_SYSVIEW_X_GetInterruptId() // Get the currently active interrupt Id from the user-provided function.
#define SEGGER_SYSVIEW_ID_BASE 0x3F400000 // Default value for the lowest Id reported by the application. Can be overridden by the application via SEGGER_SYSVIEW_SetRAMBase(). (i.e. 0x20000000 when all Ids are an address in this RAM)
#define SEGGER_SYSVIEW_ID_SHIFT 0 // Number of bits to shift the Id to save bandwidth. (i.e. 2 when Ids are 4 byte aligned)
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() ((*(U32 *)(0xE000ED04)) & 0x1FF) // Get the currently active interrupt Id. (i.e. read Cortex-M ICSR[8:0] = active vector)
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() (__get_IPSR()) // Workaround for IAR, which might do a byte-access to 0xE000ED04. Read IPSR instead.
#else
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() ((*(U32 *)(0xE000ED04)) & 0x3F) // Get the currently active interrupt Id. (i.e. read Cortex-M ICSR[5:0] = active vector)
#endif
#else
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() SEGGER_SYSVIEW_X_GetInterruptId() // Get the currently active interrupt Id from the user-provided function.
#define SEGGER_SYSVIEW_INFO_SIZE 9 // Minimum size, which has to be reserved for a packet. 1-2 byte of message type, 0-2 byte of payload length, 1-5 bytes of timestamp.
#define SEGGER_SYSVIEW_QUANTA_U32 5 // Maximum number of bytes to encode a U32, should be reserved for each 32-bit value in a packet.
#define SEGGER_SYSVIEW_LOG (0u)
#define SEGGER_SYSVIEW_WARNING (1u)
#define SEGGER_SYSVIEW_ERROR (2u)
#define SEGGER_SYSVIEW_FLAG_APPEND (1u << 6)
#define SEGGER_SYSVIEW_PREPARE_PACKET(p) (p) + 4
//
// SystemView events. First 32 IDs from 0 .. 31 are reserved for these
#define SEGGER_SYSVIEW_INFO_SIZE 9 // Minimum size, which has to be reserved for a packet. 1-2 byte of message type, 0-2 byte of payload length, 1-5 bytes of timestamp.
#define SEGGER_SYSVIEW_QUANTA_U32 5 // Maximum number of bytes to encode a U32, should be reserved for each 32-bit value in a packet.
#define SEGGER_SYSVIEW_LOG (0u)
#define SEGGER_SYSVIEW_WARNING (1u)
#define SEGGER_SYSVIEW_ERROR (2u)
#define SEGGER_SYSVIEW_FLAG_APPEND (1u << 6)
#define SEGGER_SYSVIEW_PREPARE_PACKET(p) (p) + 4
//
// SystemView events. First 32 IDs from 0 .. 31 are reserved for these
* If the OTA data partition is not present or not valid then the result is the first app partition found in the
* partition table. In priority order, this means: the factory app, the first OTA app slot, or the test app partition.
*
* Note that there is no guarantee the returned partition is a valid app. Use esp_image_load(ESP_IMAGE_VERIFY, ...) to verify if the
* Note that there is no guarantee the returned partition is a valid app. Use esp_image_verify(ESP_IMAGE_VERIFY, ...) to verify if the
* returned partition contains a bootable image.
*
* @return Pointer to info for partition structure, or NULL if partition table is invalid or a flash read operation failed. Any returned pointer is valid for the lifetime of the application.
int "Maximum topic length (not including Thing Name)"
depends on AWS_IOT_SDK
default 60
range 10 1000
help
All shadow actions have to be published or subscribed to a topic which is of the format $aws/things/{thingName}/shadow/update/accepted. This refers to the size of the topic without the Thing Name
#define AWS_IOT_MQTT_NUM_SUBSCRIBE_HANDLERS CONFIG_AWS_IOT_MQTT_NUM_SUBSCRIBE_HANDLERS ///< Maximum number of topic filters the MQTT client can handle at any given time. This should be increased appropriately when using Thing Shadow
// Thing Shadow specific configs
#define SHADOW_MAX_SIZE_OF_RX_BUFFER (AWS_IOT_MQTT_RX_BUF_LEN + 1) ///< Maximum size of the SHADOW buffer to store the received Shadow message
#define SHADOW_MAX_SIZE_OF_RX_BUFFER CONFIG_AWS_IOT_SHADOW_MAX_SIZE_OF_RX_BUFFER ///< Maximum size of the SHADOW buffer to store the received Shadow message, including NULL terminating byte
#define MAX_SIZE_OF_UNIQUE_CLIENT_ID_BYTES 80 ///< Maximum size of the Unique Client Id. For More info on the Client Id refer \ref response "Acknowledgments"
#define MAX_SIZE_CLIENT_ID_WITH_SEQUENCE (MAX_SIZE_OF_UNIQUE_CLIENT_ID_BYTES + 10) ///< This is size of the extra sequence number that will be appended to the Unique client Id
#define MAX_SIZE_CLIENT_TOKEN_CLIENT_SEQUENCE (MAX_SIZE_CLIENT_ID_WITH_SEQUENCE + 20) ///< This is size of the the total clientToken key and value pair in the JSON
#define MAX_ACKS_TO_COMEIN_AT_ANY_GIVEN_TIME 10///< At Any given time we will wait for this many responses. This will correlate to the rate at which the shadow actions are requested
#define MAX_THINGNAME_HANDLED_AT_ANY_GIVEN_TIME 10///< We could perform shadow action on any thing Name and this is maximum Thing Names we can act on at any given time
#define MAX_JSON_TOKEN_EXPECTED 120///< These are the max tokens that is expected to be in the Shadow JSON document. Include the metadata that gets published
#define MAX_SHADOW_TOPIC_LENGTH_WITHOUT_THINGNAME 60///< All shadow actions have to be published or subscribed to a topic which is of the formablogt $aws/things/{thingName}/shadow/update/accepted. This refers to the size of the topic without the Thing Name
#define MAX_SIZE_OF_THING_NAME 20///< The Thing Name should not be bigger than this value. Modify this if the Thing Name needs to be bigger
#define MAX_ACKS_TO_COMEIN_AT_ANY_GIVEN_TIME CONFIG_AWS_IOT_SHADOW_MAX_SIMULTANEOUS_ACKS///< At Any given time we will wait for this many responses. This will correlate to the rate at which the shadow actions are requested
#define MAX_THINGNAME_HANDLED_AT_ANY_GIVEN_TIME CONFIG_AWS_IOT_SHADOW_MAX_SIMULTANEOUS_THINGNAMES///< We could perform shadow action on any thing Name and this is maximum Thing Names we can act on at any given time
#define MAX_JSON_TOKEN_EXPECTED CONFIG_AWS_IOT_SHADOW_MAX_JSON_TOKEN_EXPECTED///< These are the max tokens that is expected to be in the Shadow JSON document. Include the metadata that gets published
#define MAX_SHADOW_TOPIC_LENGTH_WITHOUT_THINGNAME CONFIG_AWS_IOT_SHADOW_MAX_SHADOW_TOPIC_LENGTH_WITHOUT_THINGNAME///< All shadow actions have to be published or subscribed to a topic which is of the formablogt $aws/things/{thingName}/shadow/update/accepted. This refers to the size of the topic without the Thing Name
#define MAX_SIZE_OF_THING_NAME CONFIG_AWS_IOT_SHADOW_MAX_SIZE_OF_THING_NAME///< The Thing Name should not be bigger than this value. Modify this if the Thing Name needs to be bigger
#define MAX_SHADOW_TOPIC_LENGTH_BYTES (MAX_SHADOW_TOPIC_LENGTH_WITHOUT_THINGNAME + MAX_SIZE_OF_THING_NAME) ///< This size includes the length of topic with Thing Name
The factory reset will occur if there is a GPIO input pulled low while device starts up.
See settings below.
config BOOTLOADER_NUM_PIN_FACTORY_RESET
int "Number of the GPIO input for factory reset"
depends on BOOTLOADER_FACTORY_RESET
range 0 39
default 4
help
The selected GPIO will be configured as an input with internal pull-up enabled.
To trigger a factory reset, this GPIO must be pulled low on reset.
Note that GPIO34-39 do not have an internal pullup and an external one must be provided.
config BOOTLOADER_OTA_DATA_ERASE
bool "Clear OTA data on factory reset (select factory partition)"
depends on BOOTLOADER_FACTORY_RESET
help
The device will boot from "factory" partition (or OTA slot 0 if no factory partition is present) after a factory reset.
config BOOTLOADER_DATA_FACTORY_RESET
string "Comma-separated names of partitions to clear on factory reset"
depends on BOOTLOADER_FACTORY_RESET
default "nvs"
help
Allows customers to select which data partitions will be erased while factory reset.
Specify the names of partitions as a comma-delimited with optional spaces for readability. (Like this: "nvs, phy_init, ...")
Make sure that the name specified in the partition table and here are the same.
Partitions of type "app" cannot be specified here.
config BOOTLOADER_APP_TEST
bool "GPIO triggers boot from test app partition"
default N
help
Allows to run the test app from "TEST" partition.
A boot from "test" partition will occur if there is a GPIO input pulled low while device starts up.
See settings below.
config BOOTLOADER_NUM_PIN_APP_TEST
int "Number of the GPIO input to boot TEST partition"
depends on BOOTLOADER_APP_TEST
range 0 39
default 18
help
The selected GPIO will be configured as an input with internal pull-up enabled.
To trigger a test app, this GPIO must be pulled low on reset.
After the GPIO input is deactivated and the device reboots, the old application will boot.
(factory or OTA[x]).
Note that GPIO34-39 do not have an internal pullup and an external one must be provided.
config BOOTLOADER_HOLD_TIME_GPIO
int "Hold time of GPIO for reset/test mode (seconds)"
depends on BOOTLOADER_FACTORY_RESET || BOOTLOADER_APP_TEST
default 5
help
The GPIO must be held low continuously for this period of time after reset
before a factory reset or test partition boot (as applicable) is performed.
config BOOTLOADER_WDT_ENABLE
bool "Use RTC watchdog in start code"
default y
help
Tracks the execution time of startup code.
If the execution time is exceeded, the RTC_WDT will restart system.
It is also useful to prevent a lock up in start code caused by an unstable power source.
NOTE: Tracks the execution time starts from the bootloader code - re-set timeout, while selecting the source for slow_clk - and ends calling app_main.
Re-set timeout is needed due to WDT uses a SLOW_CLK clock source. After changing a frequency slow_clk a time of WDT needs to re-set for new frequency.
slow_clk depends on ESP32_RTC_CLOCK_SOURCE (INTERNAL_RC or EXTERNAL_CRYSTAL).
config BOOTLOADER_WDT_DISABLE_IN_USER_CODE
bool "Allows RTC watchdog disable in user code"
depends on BOOTLOADER_WDT_ENABLE
default n
help
If it is set, the client must itself reset or disable rtc_wdt in their code (app_main()).
Otherwise rtc_wdt will be disabled before calling app_main function.
Use function rtc_wdt_feed() for resetting counter of rtc_wdt.
Use function rtc_wdt_disable() for disabling rtc_wdt.
config BOOTLOADER_WDT_TIME_MS
int "Timeout for RTC watchdog (ms)"
depends on BOOTLOADER_WDT_ENABLE
default 9000
range 0 120000
help
Verify that this parameter is correct and more then the execution time.
Pay attention to options such as reset to factory, trigger test partition and encryption on boot
- these options can increase the execution time.
Note: RTC_WDT will reset while encryption operations will be performed.
endmenu # Bootloader
menu "Security features"
# These three are the actual options to check in code,
# selected by the displayed options
config SECURE_SIGNED_ON_BOOT
bool
default y
depends on SECURE_BOOT_ENABLED || SECURE_SIGNED_ON_BOOT_NO_SECURE_BOOT
config SECURE_SIGNED_ON_UPDATE
bool
default y
depends on SECURE_BOOT_ENABLED || SECURE_SIGNED_ON_UPDATE_NO_SECURE_BOOT
config SECURE_SIGNED_APPS
bool
default y
depends on SECURE_SIGNED_ON_BOOT || SECURE_SIGNED_ON_UPDATE
config SECURE_SIGNED_APPS_NO_SECURE_BOOT
bool "Require signed app images"
default n
depends on !SECURE_BOOT_ENABLED
help
Require apps to be signed to verify their integrity.
This option uses the same app signature scheme as hardware secure boot, but unlike hardware secure boot it does not prevent the bootloader from being physically updated. This means that the device can be secured against remote network access, but not physical access. Compared to using hardware Secure Boot this option is much simpler to implement.
config SECURE_SIGNED_ON_BOOT_NO_SECURE_BOOT
bool "Bootloader verifies app signatures"
default n
depends on SECURE_SIGNED_APPS_NO_SECURE_BOOT
help
If this option is set, the bootloader will be compiled with code to verify that an app is signed before booting it.
If hardware secure boot is enabled, this option is always enabled and cannot be disabled.
If hardware secure boot is not enabled, this option doesn't add significant security by itself so most users will want to leave it disabled.
config SECURE_SIGNED_ON_UPDATE_NO_SECURE_BOOT
bool "Verify app signature on update"
default y
depends on SECURE_SIGNED_APPS_NO_SECURE_BOOT
help
If this option is set, any OTA updated apps will have the signature verified before being considered valid.
When enabled, the signature is automatically checked whenever the esp_ota_ops.h APIs are used for OTA updates,
or esp_image_format.h APIs are used to verify apps.
If hardware secure boot is enabled, this option is always enabled and cannot be disabled.
If hardware secure boot is not enabled, this option still adds significant security against network-based attackers by preventing spoofing of OTA updates.
config SECURE_BOOT_ENABLED
bool "Enable secure boot in bootloader (READ DOCS FIRST)"
default N
bool "Enable hardware secure boot in bootloader (READ DOCS FIRST)"
default n
help
Build a bootloader which enables secure boot on first boot.
@@ -77,7 +224,7 @@ config SECURE_BOOT_ENABLED
When enabling secure boot, JTAG and ROM BASIC Interpreter are permanently disabled by default.
Refer to https://esp-idf.readthedocs.io/en/latest/security/secure-boot.html before enabling.
Refer to https://docs.espressif.com/projects/esp-idf/en/latest/security/secure-boot.html before enabling.
choice SECURE_BOOTLOADER_MODE
bool "Secure bootloader mode"
@@ -104,12 +251,12 @@ endchoice
config SECURE_BOOT_BUILD_SIGNED_BINARIES
bool "Sign binaries during build"
depends on SECURE_BOOT_ENABLED
depends on SECURE_SIGNED_APPS
default y
help
Once secure boot is enabled, bootloader will only boot if partition table and app image are signed.
Once secure boot or signed app requirement is enabled, app images are required to be signed.
If enabled, these binary files are signed as part of the build process. The file named in "Secure boot private signing key" will be used to sign the image.
If enabled (default), these binary files are signed as part of the build process. The file named in "Secure boot private signing key" will be used to sign the image.
If disabled, unsigned app/partition data will be built. They must be signed manually using espsecure.py (for example, on a remote signing server.)
Path to the key file used to sign partition tables and app images for secure boot. Once secure boot is enabled, bootloader will only boot if partition table and app image are signed.
Path to the key file used to sign app images.
Key file is an ECDSA private key (NIST256p curve) in PEM format.
bool "Allow app partition length not 64KB aligned"
depends on SECURE_BOOT_INSECURE
help
If not set (default), app partition size must be a multiple of 64KB. App images are padded to 64KB length, and the bootloader checks any trailing bytes after the signature (before the next 64KB boundary) have not been written. This is because flash cache maps entire 64KB pages into the address space. This prevents an attacker from appending unverified data after the app image in the flash, causing it to be mapped into the address space.
Setting this option allows the app partition length to be unaligned, and disables padding of the app image to this length. It is generally not recommended to set this option, unless you have a legacy partitioning scheme which doesn't support 64KB aligned partition lengths.
@@ -8,12 +8,19 @@ Linker file used to link the bootloader.
The main purpose is to make sure the bootloader can load into main memory
without overwriting itself.
*/
MEMORY
{
/* I/O */
dport0_seg (RW) : org = 0x3FF00000, len = 0x10
/* IRAM POOL1, used for APP CPU cache. We can abuse it in bootloader because APP CPU is still held in reset, the main app enables APP CPU cache */
iram_seg (RWX) : org = 0x40078000, len = 0x8000
/* IRAM POOL1, used for APP CPU cache. Bootloader runs from here during the final stage of loading the app because APP CPU is still held in reset, the main app enables APP CPU cache */
iram_loader_seg (RWX) : org = 0x40078000, len = 0x8000 /* 32KB, APP CPU cache */
/* 63kB, IRAM. We skip the first 1k to prevent the entry point being
placed into the same range as exception vectors in the app.
This leads to idf_monitor decoding ROM bootloader "entry 0x40080xxx"
message as one of the exception vectors, which looks scary to users.
*/
iram_seg (RWX) : org = 0x40080400, len = 0xfc00
/* 64k at the end of DRAM, after ROM bootloader stack */
/* @brief Encode one or more sets of 6 byte sequences into
* 8 bytes suitable for 3/4 Coding Scheme.
*
* This function is only useful if the CODING_SCHEME efuse
* is set to value 1 for 3/4 Coding Scheme.
*
* @param[in] in_bytes Pointer to a sequence of bytes to encode for 3/4 Coding Scheme. Must have length in_bytes_len. After being written to hardware, these bytes will read back as little-endian words.
* @param[out] out_words Pointer to array of words suitable for writing to efuse write registers. Array must contain 2 words (8 bytes) for every 6 bytes in in_bytes_len. Can be a pointer to efuse write registers.
* @param in_bytes_len. Length of array pointed to by in_bytes, in bytes. Must be a multiple of 6.
*
* @return ESP_ERR_INVALID_ARG if either pointer is null or in_bytes_len is not a multiple of 6. ESP_OK otherwise.
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
