Issue is that when users creates a custom bootloader from
$IDF_PATH/components/bootloader. Parent project build uses the copy but
bootloader subproject build uses the original still. The issue is solved
by passing the custom bootloader as extra component directory so
bootloader build knows to use the new copy (itself) in the build.
Fixed the case when the first part of log was missed
this was happened when:
* CONFIG_CONSOLE_UART_CUSTOM option is selected (UART1)
* The selected CONSOLE_UART port is used also for the console component
* in code esp_restart() or abort() functions were called.
Earlier eraseItem function in Storage class would do lazy cleanup of
multi-page blobs if called using type "ANY" instead of "BLOB". It used to
just delete BLOB data and index would remain as is. Any subsequent read
would delete index entry as well. This however would return a valid
length without error if nvs_get_blob API was just used for finding
length and not reading the complete blob. This change fixes this issue.
Closes https://github.com/espressif/esp-idf/issues/3255
Backport following WiFi fixes to v3.2:
1. Add support for STA HT2040 coexist management
2. Add support for WPA2 improvements
3. Disallow HT rate when unicast/mcast cipher is TKIP/WEP
4. Add support for signal test
5. Fix the bug that WPS fails when AP is encrypted
List of changes:
* When parsing requests, count termination from LF characters only
* Correct memcpy() length parameter in httpd_unrecv() (pointed out by jimparis in GitHub issue thread)
* Use ssize_t to store results of length subtractions during parsing
* Modify some comments to reduce ambiguity
Closes https://github.com/espressif/esp-idf/issues/3182
Fixed adjtime function: While using the adjtime() function,
the time correction accumulated an error
when reading the time frequently (using gettimeofday).
Operation:
In `esp_http_client_set_url`, we check for if old_host is same as new_host.
Delete and open new connection if host is different.
Issue:
We just pointed `client->connection_info.host` to `old_host` and reassigned it.
This made old_host and new_host always point to same location and hence, using old_host with new request.
Fix:
Made a separate copy for old_host using strdup.
Closes https://github.com/espressif/esp-idf/issues/2631
Signed-off-by: Vikram Dattu <vikram.dattu@espressif.com>
1. remove redundant SPI clock settings, use rom functions to set clock.
2. remove redundant SPI cs setup and hold settings.
3. for old 32Mbit psram, cs hold time must only be 0.5T due to the special driving mode.(cs_setup = 0; cs_hold = 0)
4. for new 64Mbit psram, cs hold time is recommended to be 2.5T. (cs_setup = 1, cs_setup_time = 0;cs_hold = 1, cs_hold_time = 1)
1. Softap support multicast and broadcast saving and flushing
when the associated stations enable IEEE80211 legacy power
save(which is called modem sleep in ESP32).
2. Improve the frame saving and flushing mechanism of softap power
save.
Fix following WiFi and coexist bugs:
1. Fix BT disconnecting due to too many reset BB
2. Fix the bug that no TBTT is generated after rx wrong beacon when WiFi/BT coexist
3. Fix a DelBA bug
4. Add out of memory check
5. Fix the bug that STA incorrectly receives packets when scanning in connected status
6. PHY4008: Disable BT TX in force wifi mode, and enable BT TX in un-force wifi mode
1. fix the bug block scan tiemout before scan finish
2. make menuconfig can set the WiFi mgmt short buffer num
3. modify wifi reason code
4. fix the bug PMK recal too long
1.Fix memory leak when set txpower
2.Fix some bugs
Disconnect with apple device
hci_refresh_enc_key_cmd will be ignore
hci_refresh_enc_key_cmd will crash
1. Pass the correct conn_id to protocomm_req_handle
In transport_simple_ble_write(), passing param->exec_write.conn_id would
be invalid. Instead param->write.conn_id should be passed
Similar change in transport_simple_ble_exec_write() to use
param->exec_write.conn_id
2. simple_ble_start() assumes that the mode is BLE only and enables
Bluetooth controller accordingly. For, cases having BT + BLE like Alexa
(Provisioning over BLE + Audio over classic BT), this assumption should
be removed.
This fix prevents HTTP server from accepting new connections when the total count of connected
sockets has reached the max_open_sockets limit set during configuration. The pending connections
are kept in backlog until atleast one of the connected sockets is closed. The maximum number of
connection requests that can kept in backlog is specified as backlog_conn configuration option.
Note that this modification has no effect when LRU purge is enabled.
Also added sanity check on setting for max_open_sockets during configuration.
Solution suggested by jimparis https://github.com/espressif/esp-idf/issues/3183#issue-421234265
Closes https://github.com/espressif/esp-idf/issues/3183
The requirements of pin capabilites is different for spi master and
slave. The master needs CS, SCLK, MOSI to be output-able, while slave
needs MISO to be output-able.
Previous code is for master only.
This commit allows to place other 3 pins than MISO on input-only pins
for slaves. Refactoring for spi_common is also included.
Resolves https://github.com/espressif/esp-idf/issues/2455
Works around bug where components/soc/CMakeLists.txt was testing "EXISTS
${COMPONENT_PATH}/${SOC_NAME}" and this test could pass during early
expansion if COMPONENT_PATH was empty and a directory /esp32 exists
on Windows.
Closes https://github.com/espressif/esp-idf/issues/3195
newlib uses significantly more stack space when printing to an
unbuffered stream. To reduce the amount of stack space required to
use the console, don’t disable buffering. linenoise should support
unbuffered stdout instead.
Issue: MDNS server initially sends probing packets to resolve naming confilicts with already registered service instances. In case of a conflict, instance name is altered and probing restarts. Original instance however wasnnot removed from the structure and upon service removal only one entry was removed and a dangling service might have been kept in the structure to bring about a crash.
Resolution: Keep only one instance of a service in the probing structure.
Closes IDF-438
possible race condition: user task runs mdns_init, which enables pcbs while mdns-task already created could execute enable/disable of the same pcbs if an appropriate system event received
mnds_free() initiates stop and delete timer tasks, which after locking the mutex could lead to a dead lock in case timer task executed before deleting the task, as it would wait indefinitelly for unlocking the mutex. This condition is fixed by calling _mdns_stop_timer without locking the mutex, because there's no need to protect any data when stopping and deleting the timer task
Closes https://github.com/espressif/esp-idf/issues/1696
Issue: mdns_service_add API allocates and queues an action to be processed in mdns task context; when allocation or queueing fails, allocated structure needs to be freed. Function _mdns_free_service did not only fee all the structures, but also updates packet data.
Resolution: Moved removal of packet data outside of _mdns_free_service function.
packets scheduled to transmit are pushed to action queue and removed from tx_queue_head structure, which is searched for all remaining services and while service is removed, then service questions/asnwers are also removed from this structure. This update fixes possible crash when packet is pushed to action queue, and when service is removed, its answers are removed from tx_queue_head, but not from action queue. this could lead to a crash when the packet is poped from action queue containing questions/answers to already removed (freed) service
Closes IDF-438
mdns_search_once_t::lock is used to synchronize tasks (taken by one
task and given by the other) so it should not be a mutex.
Convert to semaphore, and rename to indicate its purpose.
When generating JSON metadata for ranges where there are conditional ranges (ie different allowed range
depending on another config setting), the JSON metadata would always have the last named range as
the expression was not evaluated properly.
Thanks to ulfalizer on GitHub for pointing this out.
Closes https://github.com/espressif/esp-idf/issues/2195
By default, if a URI handler changes the http session context,
the webserver internally clears the older context after the handler
returns. However, if applications want to change this behavior and
manage the allocation/de-allocation/freeing themselves and let the
server handle only the "socket close" case, this commit provides such
an option.
When xPortGetCoreID() is called twice within a function,
it might only be called once after compilation. This
commit makes the inline assembly of the function volatile.
Closes#3093
Previously when HashList was removing items, HashListBlocks were
removed lazily. This resulted in empty HashListBlocks dangling around
in full pages, even when all items have been erased. These blocks
would only be deleted when NVS was re-initialized
(nvs_flash_deinit/nvs_flash_init).
This change does eager cleanup instead, based on the code from
@negativekelvin offered in
https://github.com/espressif/esp-idf/issues/1642#issuecomment-367227994.
Closes https://github.com/espressif/esp-idf/issues/1642.
1. ref_clock used in unit tests occasionally produces time off by ~100
microseconds shortly after being started. Add a delay to let
ref_clock stabilise, until the cause is found.
2. Reduce roundoff error accumulation which would occasionally cause
the test to fail, by choosing an overflow value which can be divided
by APB frequency.
3. Move time sampling part of the test into an IRAM function to
reduce variations due to cache behavior.
4. Remove calculation of "standard deviation" in the test, as what was
calculated was not actually standard deviation, and it did not add any
useful information.
1. call esp_timer_get_time and ref_clock_get in the same order on
start and in the loop
2. disable interrupts when calculating delta between ref_clock
and esp_timer
3. ensure both functions are in cache before calculating the delta
In the situation when bootloader was compiled for 240MHz, and app was
compiled for 160MHz, and the chip is a revision 0 chip, the
bootloader will assume that the application has also been running at
240MHz. This will cause the chip to lock up later. Modify this to use
a run time check of DPORT_CPUPERIOD_SEL, which indicates which of the
PLL frequencies was used.
Closes https://github.com/espressif/esp-idf/issues/2731.
1. When one of the COMPONENT_DIRS points to a component directory
(i.e. a directory containing component.mk, not a directory of multiple
components), and there is a subdirectory in it which also contains
a component, the subdirectory was mistakenly added to the list of
components and compiled.
For example:
main/
component.mk
main.c
test/
component.mk
test_main.c
Would compile test_main.c and link libtest.a.
2. When one of the COMPONENT_DIRS points to a component directory, and
the parent directory contained a directory with the same name as
another component, that directory would be mistakenly added to the
COMPONENT_PATHS.
For example:
esp/
esp-idf/
esp32/
(random stuff)
mycomponent/
component.mk
mycomponent.c
myproject/
main/
Makefile
and Makefile sets EXTRA_COMPONENT_DIRS=$(realpath ../mycomponent),
then "esp32" directory which is at the same level as mycomponent
was added to COMPONENT_PATHS.
3. If EXTRA_COMPONENT_DIRS pointed to a directory with a list of
components, and one of the subdirectories was not a component, but
had the same name as another component, than that directory would be
mistakenly added to COMPONENT_PATHS instead of the real esp32
component directory.
For example:
my_components/
my_component/
component.mk
my_component.c
esp32/
(some random stuff)
and EXTRA_COMPONENT_DIRS would point to my_components/, then "esp32"
directory would be added to COMPONENT_PATHS instead of the real esp32
component directory.
Previously, this compiler flag was not being applied
regardless of CONFIG_SPIRAM_CACHE_WORKAROUND setting.
Explanation: add_compile_options() only applies to
source files added after the function is run, or in
subdirectories added after the function is run. In
this case, no new source files were being added after
this function was run.
1. Add missing get function to RMT API: rmt_get_idle_level().
2. Suppress error message from rmt_wait_tx_done() if wait_time==0 (allows for polling).
3. Remove the blank lines between parameter lists.
Merges https://github.com/espressif/esp-idf/pull/2666
fix 3 bugs:
1. do BLE connect (both of slave and master), it mgiht cause crash due to there's much interrupts happens effect ble code running, for example, wifi run on the same core as bluetooth controller and wifi run throughtput test.
2. do BLE scan stop or adv stop or connection stop, it might cause ASSERT or crash due to memory corrupted in controller memory poll.
3. minor bug fix, not really effect bluetooth.
when running a query for a single txt, result entries were not created and attached to result structure. this issue was introduced when fixing memory leak in txt structure, which worked correctly for PTR queries, but caused trouble for TXT query.
The bug will cause memory corrupted (the largest range is from 0x3ffc0000 ~ 0x3ffc8000),
some strange error will happen, like IllegalInstruction, LoadProhibited and .etc.
Note : Examples have been updated to prevent invocation of bluedroid/wifi APIs from inside timer callback when stopping provisioning. Workaround is to spawn new task from inside the timer callback.
List of changes:
* Corner case exceptions are properly handled to ensure release of memory occupied by security infrastructure
* fixed erroneous cleanup of security instance by protocomm_console
List of changes:
* Version endpoint now sends the set version string instead of verifying the incoming version string. This simplifies fetching version info from the provisioning application.
* esp_prov script updated to expect version string as response.
This will be useful if a webserver is already running and the application
does not want protocomm to start a new instance.
Signed-off-by: Piyush Shah <piyush@espressif.com>
1. esp32-pico use standard spi driver to access psram
2. for esp32-pico, flash and psram share the clock
3. for esp32-pico, psram cs io can be overwrite via menuconfig
1. Use BIT[7:5] of EID to determine psram size
2. Add ID support for 16Mbit psram
3. Remove module reset on SPI1
4. Confirmed with the vendor that only the old 32Mbit psram need special clock timing. For other psram chips, we should use standard QPI mode.
Files where stack protector is initialized should not be compiled with
stack protector enabled. This was done for Make but missing for CMake.
Fixes https://github.com/espressif/esp-idf/issues/2990.
* http_sess_set_*_override APIs are now the only ones available to set custom recv/send/pending functions
* Fixed side effects to using http_sess_set/get_context inside URI handlers
Changes:
- renamed `httpd_free_sess_ctx_fn_t` to `httpd_free_ctx_fn_t`
- added a `httpd_handle_t` argument to `httpd_send_func_t` and `httpd_recv_func_t`
- internal function `httpd_sess_get()` is no longer static, as it's used in other
files besides httpd_sess.c
Bug fixes:
- removed a trailing semicolon from `HTTPD_DEFAULT_CONFIG()`
- fixed issue with failed `select()`, now it automatically closes invalid sockets
instead of shutting down the entire server
New features:
- `httpd_resp_send()` and `httpd_resp_send_chunk()` now accept -1 as length to use
`strlen()` internally
- added `httpd_sess_set_ctx()` to accompany `httpd_sess_get_ctx()`
- added a "transport context" to the session structure (next to user context)
- added `httpd_sess_{get,set}_transport_ctx()` to work with this transport context
- added "global user context" and "global transport context" stored in the server
config (and then the handle); supports a user-provided free_fn
- added a "pending func" to e.g. check for data in the transport layer receive
buffer
- added functions `httpd_set_sess_{send,recv,pending}_override()` that target
a session by ID (i.e. not using a request object)
- added `httpd_set_pending_override()`
- added a "open_fn" and "close_fn" - functions called when creating and closing
a session. These may be used to set up transport layer encryption or some other
session-wide feature
Fix following WiFi bugs:
1. Fix a crash bug which is caused by WiFi static TX buffer alloc/free.
2. Fix the bug that iphone fails to connect to ESP32 AP by enabling AP BAR receiving.
3. Fix the bug that ESP32 station fails to connect some APs, such as Xiaomi hotspot etc,
after reset.
esp32: update libphy.a to fix interrupt watchdog when WiFi and BT run at the same time and both enable modem sleep (backport v3.2)
See merge request idf/esp-idf!4192
Shortcircuit evaluation may cause skip of _mdns_strdup_check of any further question field, which after clear_rx_packet freed undefined memory.
Fixes https://ezredmine.espressif.cn:8765/issues/28465
Shortcircuit evaluation may cause skip of _mdns_strdup_check of any further question field, which after clear_rx_packet freed undefined memory.
Fixes https://ezredmine.espressif.cn:8765/issues/28465
This commit adds the ability for backtracing to trace from the itnerrupt to the
task stack, and across nested interrupts. Test cases have also been added.
See MR !4084
Originally, when doing BLE active scan, Bluedroid will not report adv to
application layer until receive scan response. This option is used to
disable the behavior. When enable this option, Bluedroid will report
adv data or scan response to application layer immediately.
1. fix network channel switch function.
2. support not configuring the network channel.
3. support not configuring the router BSSID even if the router is hidden.
4. add allow_channel_switch to mesh configuration.
5. add allow_router_switch to mesh router configuration.
6. support handling beacon without IE of DS Parameter Set.
7. fix Wi-Fi RX fails in a specific scenario (update libphy.a).
8. fix STAs can not detect disconnection from AP when encrypt transmission is used.
9. fix can not find hidden APs.
10. for root, modify the active scan time to 120ms.
11. remove all rc when clear parent Wi-Fi configuration.
12. fix memory leak caused by the remove announcement being sent is not released when esp_mesh_stop() is called.
13. fix modify IE encrypt after mesh is started.
14. ignore esp_mesh_connect() if mesh automatic reconnection is enabled.
15. fix reason is cleared before vote is done.
16. fix issues in the example of manual_networking when mesh network is encrypted.
17. detect and fix root conflicts when router BSSID is not set.
18. when root can not connect to the router due to NO_MORE_STAS(reason code:5), root will stop re-connection and perform MESH_NWK_LOOK_FOR_NETWORK.
19. wifi: fix the disconnection caused by receiving a deauth frame from non-parent node during scanning.
20. fix routing table redundant issue due to the remove announcement is not 100% reliable.
21. modify the max routes limitation from 300 to 1000.
22. wifi: fix ap does not deauth the sta which has not yet completed the 4-way handshake but the max replay count is reached.
Previously, hardware SHA engine "locks" were mutex semaphores. This meant that the task which
started a particular SHA session (in hardware) needed to finalise that session, or an invalid
FreeRTOS state was created.
Replace with binary semaphore which can be shared between tasks.
Includes a unit test, but unit test doesn't crash even without this fix
(some other unknown condition is required).
Bootloader used to calculate the number of cache pages assuming that
load address was aligned, while in reality load address for DROM and
IROM was offset by 0x20 bytes from the start of 64kB page. This
caused the bootloader to map one less page if the size of the image
was 0x4..0x1c less than a multiple of 64kB.
Reported in https://esp32.com/viewtopic.php?f=13&t=6952.
If zero-overhead loop buffer is enabled, under certain rare conditions
when executing a zero-overhead loop, the CPU may attempt to execute an invalid instruction. Work around by disabling the buffer.
Due to a hardware limitation in ESP32, the first four bytes of some
CSI data is invalid, not the last four bytes.
Correct a mistake of CSI sub-carrier index in documentation.
closes https://github.com/espressif/esp-idf/issues/2494
closes https://github.com/espressif/esp-idf/pull/2493
closes https://github.com/espressif/esp-idf/pull/2496
1. Change bus reset to handle interrupted READ sequences.
2. Slow down I2C to 100khz during reset
3. If a SLAVE device was in a read operation when the bus was interrupted, the SLAVE device is controlling SDA.The only bit during the 9 clock cycles of a byte READ the MASTER(ESP32) is guaranteed control over, is during the ACK bit period.
If the SLAVE is sending a stream of ZERO bytes, it will only release SDA during the ACK bit period. The master(ESP32) cannot generate a STOP unless SDA is HIGH. So, this reset code synchronizes the bit stream with, Either, the ACK bit, Or a 1 bit.
I am stealing this delay coding from @jeremyherbert #2493 pr.
2. Change Bus Reset to handle interrupted READ sequences.
The current code does not handle interrupted READ cycles.
If a SLAVE device was in a read operation when the bus was interrupted, the SLAVE device is controlling SDA.
The only bit during the 9 clock cycles of a byte READ the MASTER(ESP32) is guaranteed control over, is during the ACK bit period.
If the SLAVE is sending a stream of ZERO bytes, it will only release SDA during the ACK bit period. The master(ESP32) cannot generate a STOP unless SDA is HIGH.
So, this reset code synchronizes the bit stream with, Either, the ACK bit, Or a 1 bit.
3. fix typo
correct `sda_id` to `sda_io` in `i2c_master_clear_bus()` @ryan-ma found it. This typo was generated when I manually edited this patch on GitHub, I should have done a Copy/Paste operation!
1. fix bug PHY/RTC functions called in ISR (update phy to v4007)
2. add UnitTest to test it
3. fix task watchdog bug when wifi change channel
4. disable/enable agc to mac deinit/init
tools: Be more helpful to MSYS32 users with package installation & check if current python is inside virtual environment (backport v3.2)
See merge request idf/esp-idf!4063
state and reduce force receiving broadcast data time
1. If receiving beacon which indicates that there is no data buffered,
do not force to receive WiFi data.
2. If receiving beacon which indicates that there is broadcast data
buffered, reduce the time to force receiving broadcast data.
timer_process_alarm function of esp_timer holds a spinlock for the
entire duration of its operation, except for the time when timer
callback function is called. It is possible that when
timer_process_alarm releases the spinlock, a higher priority task may
run and delete the timer. Then the execution will return to
timer_process_alarm, and this will either cause a crash, or undesired
execution of callback after the timer has been stopped or deleted.
To solve this problem, add a mutex which will prevent deletion of timers
while callbacks are being dispatched.
It has been observed that, in case of underflow (data unavailability) in
I2S transmission, previously filled up tx descriptors continue to get
transmitted on line, causing noise in case of audio use case.
This change adds optional `tx_desc_auto_clear` field during I2S driver intialization
than can zero initialize tx descriptor in case of underflow situation in
interrupt handler itself.
Closes: https://github.com/espressif/esp-idf/issues/1789
(cherry picked from commit 765bf674d0)
Update freemodbus component file esp-idf/components/freemodbus/port/portserial.c to remove UART mode settings;
Move UART mode settings into esp-idf/examples/protocols/modbus_slave/main/freemodbus.c
Move UART pin settings from Component config into example Kconfig.projbuild file
Move setup of UART port pins from freemodbus component into example file
TW#27721
Closes https://github.com/espressif/esp-idf/issues/2784#issuecomment-443600157
A workaround to reset BBPLL configuration after light sleep. Fixes the
issue that Wi-Fi can not receive packets after waking up from light
sleep.
Ref. https://github.com/espressif/esp-idf/issues/2711
On enabling flash encryption, OTA fails with magic byte error in the second chunk
if the http data is split into two or more chunks and first chunk is less than 16.
This fix includes following changes:
1. Fix the bug that esp_restart()/esp_wifi_stop() sometimes fails in WiFi/BT coexist mode.
2. Add a timer for WiFi stop and stop WiFi forcibly once the timer expires.
1. start an esp_timer on entering sleep to acquire pm_lock before wake up from modem sleep
2. decrease the clock division of XTAL fed to bluetooth low power clock from 32us to 2us period to allow to work under 240MHz Max CPU frequency
3. decrease the minimum sleep duration threshold to allow shorter bluetooth modem sleep period, especially for BLE with short connection interval
4. reconfigure bluetooth baseband(BT-BB) settings after PHY/RF init upon waking up from modem sleep to avoid packet RX/TX performance degradation
Hostname option has been removed from dhcp discover since IDFv3.2.
But it remains in dhcp request due to which ESP32 can not get IPv4 address
from some APs. Re-add hostname option to dhcp discover to solve this issue.
When ethernet enable again after disable it before, phy init will report timeout.
The cause of this problem is that the enabling of emac clock is too late, and should be placed before phy init.
Introduced in 9c23b8e5 and 4f87a62f. To get higher speed, menuconfig
options are added to put ISR and other functions into the IRAM. The
interrupt flag ESP_INTR_FLAG_IRAM is also mistakenly set when the ISR is
put into the IRAM. However callbacks, which are wrote by the user, are
called in the master and slave ISR. The user may not be aware of that
these callbacks are not disabled during flash operations. Any cache miss
during flash operation will cause panic.
Essentially IRAM functions and intrrupt flag ESP_INTR_FLAG_IRAM are
different, the latter means not disabling the ISR during flash
operations. New bus_config flag intr_flags is offered to help set the
interrupt attribute, including priority level, SHARED, IRAM (not
disabled during flash operations). It introduced a small BREAK to
IDFv3.1 (but the same as IDFv3.0) that the user has to manually set IRAM
flag now (therefore he's aware of the IRAM thing) to void the ISR being
disabled during flash operations.
1. Fix interrupt watchdog timeout in bluetooth "btdm_bb_isr"
2. Fix BLE assert(512) or assert(1536) in rwble.c at line 222
3. Update librtc.a to fix BLE assert(512) in rwble.c at line 222
The #1 and #2 occurs random.
The #3 bug occurs in certain scenario:
1. If Wifi start softap and BLE is working
2. If wifi start station, but do not use normal station operation, such
as just use espnow, while BLE is working
3. Any other scenario, that wifi works without use software coexist
operation, while BLE is working(such as do advertising and ...)
4. update libcoexist.a version to v1.1.2
The number of runners of integration test is not bottleneck to CI
pipeline performance now. Combine these 2 stages will make integration
test executed even unit test fails. This could help us to collect more
info about test history.
1. replace xunitgen with junit_xml, which can log more info
2. allow test cases to handle junit test report by them own
3. allow test cases to log some info into report via `sysout` tag
Fix some Wifi bugs:
1. Enable RX BAR
2. Fix the bug that ESP32 AP negotiates with iphone to 11g
3. Fix the bug that ESP32 STA has ap_loss because CMCC AP contains two SSID
1. fix failture of mesh stop caused by block-sending.
2. fix when FIXED_ROOT is set, 2nd layer devices can not receive mesh event ESP_ERR_MESH_NO_PARENT_FOUND.
3. fix when FIXED_ROOT is set and the root turns off mesh function, 2nd layer devices do not look for new parents.
4. add APIs esp_mesh_disconnect() and esp_mesh_connect().
5. disconnect from parent/router when the DSSS channel in received beacon is different from the home channel.
6. remove nvs task to release 3k bytes memory.
Having two different spinlocks is problematic due to possibly
different order in which the locks will be taken. Changing the order
would require significant restructuring of kernel code which is
undesirable.
An additional place where taking xTickCountMutex was needed was in
vApplicationSleep function. Not taking xTickCountMutex resulted in
other CPU sometimes possibly advancing tick count while light sleep
entry/exit was happening. Taking xTickCountMutex in addition to
xTaskQueueMutex has shown a problem that in different code paths,
these two spinlocks could be taken in different order, leading to
(unlikely, but possible) deadlocks.
When light sleep is finished on one CPU, it is possible that the other
CPU will enter light sleep again very soon, before interrupts on the
first CPU get a chance to run. To avoid such situation, set a flag
for the other CPU to skip light sleep attempt.
Tickless idle/light sleep procedure had a bug in single core mode.
Consider the flow of events:
1. Idle task runs and calls vApplicationIdleHook
2. This calls esp_vApplicationIdleHook, which calls esp_pm_impl_idle_hook, and pm lock for RTOS on the current core is released.
3. Then esp_vApplicationIdleHook calls esp_pm_impl_waiti, which checks that s_entered_light_sleep[core_id]==false and goes into waiti state.
4. Some interrupt happens, calls esp_pm_impl_isr_hook, which takes pm lock for RTOS. PM state goes back to CPU_FREQ_MAX.
5. Once the interrupt is over, vApplicationIdleHook returns, and Idle task continues to run, finally reaching the call to vApplicationSleep.
6. vApplicationSleep does not enter light sleep, because esp_pm_impl_isr_hook has already changed PM state from IDLE to CPU_FREQ_MAX.
This didn’t happen in dual core mode, because waiti state of one CPU was interrupted by CCOMPARE update interrupt from the other CPU, in which case PM lock for FreeRTOS was not taken.
Fix by inverting the meaning of the flag (for convenience) and only setting it to true when vApplicationSleep actually fails to enter light sleep.
1. Fix the bug that disable controller suddenly cause crash when ble is working.
2. Fix the bug that when disable controller, it will cause wifi cannot RX, TX timeout, buffer lack and etc.
1. If L2_TO_L3_RX_BUF_MODE is not selected, we must assign l2_owner explictly before we call pbuf_free.
2. free intr resource in esp_eth_deinit
Closes https://github.com/espressif/esp-idf/issues/2670
1. Original register mapping for LAN8720 has some registers that doesn't exist/support.
So just remove them, and fix the power and init function for LAN8720.
2. GPIO16 and GPIO17 is occupied by PSRAM, so only ETH_CLOCK_GPIO_IN mode is supported in that case if using PSRAM.
3. Fix bug of OTA failing with Ethernet
4. Fix bug of multicast with Ethernet
5. Fix potential memory leak
mdns queries did not work properly when send imeadiately after set_hostname, which cuased reinit of pcb and therefore restarted probing, so search packets were blocked until probing finished
closes#2507, closes#2593
1. fix ap_loss that occurs when the parent turns off the mesh function and becomes a normal WiFi with a different SSID.
2. add an event MESH_EVENT_NETWORK_STATE that contains information about whether there is a root in the current network.
3. modify the mechanism of mesh IE update.
4. fix a problem in the process of re-voting to select the root, the device that does not meet the conditions of being a root votes for itself.
5. fix an issue that occurs in esp_mesh_recv_toDS() when stopping the mesh.
6. when the user specifies a parent for the device, the device will set the authmode and password of its AP mode to the same value as the specified parent.
7. add two disconnected reason codes MESH_REASON_EMPTY_PASSWORD and MESH_REASON_PARENT_UNENCRYPTED.
This commit resolves a blocking in esp_aes_block function.
Introduce:
The problem was in the fact that AES is switched off at the moment when he should give out the processed data. But because of the disabled, the operation can not be completed successfully, there is an infinite hang. The reason for this behavior is that the registers for controlling the inclusion of AES, SHA, MPI have shared registers and they were not protected from sharing.
Fix some related issue with shared using of AES SHA RSA accelerators.
Closes: https://github.com/espressif/esp-idf/issues/2295#issuecomment-432898137
1. When WIFI task or other high priority task blocks the Bluetooth task, ACL RX buffer will use up, ACL RX buffer ptr will point to null and will never point to a valid adress. Causing errors in Bluetooth.
2. hcimsgs.h used whether flow control is on or off
Introduced in 97e3542947.
The previous commit frees the IRAM part when single core, but doesn't
change the memory layout functions. The unit test mallocs IRAM memory
from the heap, accidently into the new-released region, which doesn't
match the memory layout function.
This commit update the memory layout function to fix this.
Problem Decribe
The problem happenned when do wps with a mikrotik router
1. router always want to do connect with 32 without EAP-WSC step
2. after 4 way timeour, 32 crash
Root Cause
The reason why can not start EAP-WSC step is router's check method is RSN > WPA > WPS, when it found there include RSN and WPS in assoc, it will choice do 4 way rather than WPS
The reason of second problem is 32's EAPOL start timer didn't stop and send EAPOL start to a null pointer
Soultion
1. remove RSN and WPA ie when do WPS step
2. check mac address's pointer before send EAPOL start
closes: https://github.com/espressif/esp-idf/issues/2382
There's still a small chance that can't process command issue still
happen on some runners. Now we change the way to detect if the runner
reset finished: input `-` to check test history for a few times until it
succeeded. If DUT can process check history command, then it should be
able to process other test commands.
Fix following WiFi bugs:
1. Fix the bug that MIC verification fails on soft-AP mode
2. Modify mesh root to have same behavior as normal WiFi STA in state change
3. Fix the bug that sniffer can't catch control packets
4. Fix crash bug in soft-AP mode
5. Fix ACM(Admission Control Management) bug
1) two events AP_STOP, AP_START shortly after each other may cause IGMP config on already stopped netif
2) not properly locked sending packets to queue from timer task
closes#2580
Gitlab CI now allow us to define if a job need to be created by
varialbes. This commit add label to CI jobs, so we can make some jobs
not created in certain scenarios when we trigger pipeline with @bot.
Routine `spi_flash_cache2phys` sometimes return incorrect value,
resulting in failure in getting currently running ota partition.
This in turn aborts firmware update process.This issue was more
prominent with SPIRAM enabled cases.
Fix ensures proper cache guards during `spi_flash_cache2phys`, and
also for few other similar APIs.
In addition, `esp_ota_get_running_partition` has also been optimized
to save currently running partition for subsequent invocations.
Fixes https://github.com/espressif/esp-idf/issues/2451
In earlier change this component was decoupled from freertos and hence
regression was introduced which changed default placement to flash. Some
device drivers make use of ringbuffer while flash cache is being disabled
and hence default placement should instead be internal memory.
Closes: https://github.com/espressif/esp-idf/issues/2517
1. fix some bugs by previous coex hw blocking bugfix,
such like, rwble.c (64, 0) line 222
2. fix bug that ble scan performance is very low when software coexist
is working.
3. update libcoexist version to v1.1.0
Previous version assumed having winpty on the Path meant that it would be needed,
but some tools (like Atlassian Sourcetree) permanently add winpty to the path.
Symptom is arrow keys not working in menuconfig dialog.
Uninstaller is still unsigned, as currently building and signing in 'wine'
and running Linux osslsigncode inside Inno Setup inside wine is awkward.
Closes https://github.com/espressif/esp-idf/issues/1909
TW20810
This feature allows `httpd_req_recv()` and `httpd_send()` functions to return
specific `HTTPD_SOCK_ERR_` codes in case of socket errors. This is useful
in case of errors like `EAGAIN`, `EINTR`, etc. when the user may want to
retry `httpd_req_recv()` / `httpd_send()` function call.
This example adds functionality to support basic communication in RS485 networks using Modbus protocol.
This example uses FreeModbus stack and regular UART driver API to communicate in RS485 half duplex mode.
Added initial support of modbus controller pure C api to access device parameters over Modbus transport.
Move freemodbus stack and port files into components folder
Move the modbus_controller interface into components idf folder
Source files updated after review.
Add modbus interface documentation docs/en/api-reference/protocols/modbus.rst
porttimer.c: fix bug with timer1 selected in the Kconfig
Add support of cmake system (added cmake files)
Closes https://github.com/espressif/esp-idf/issues/858
In some cases, when data was just written into UART FIFO, transmitter
state could be still zero while the FIFO did contain some data.
This resulted in uart_tx_wait_idle occasionally returning before all
the data was sent out.
Fix by checking both UART transmitter state and TX FIFO count.
ROM definition of `abort` was removed in 9240bbb. The old definition
resulted in a panic due to a jump to a null pointer (abort member in
ROM stub table was zero). The new definition triggers a debug
exception if JTAG is connected, or goes into an infinite loop to be
reset by the WDT.
Some logging done in soc component may happen before logging via
stdout is possible. Use _EARLY version of log calls to make sure that
output is visible. The downside is that application does not have a
way to silence these logs. However since the soc component doesn’t
use any LOGV/LOGD/LOGI and only logs warnings and errors, this should
not impact the application.
This commit updates some of the API references in task.h so
that stack sizes are referred to in bytes rather than words as
found in the vanilla version.
Closes#2528
1. Fix the bug that ESP32 will reject the retry AddBA request frame
if AddBA response frame is failed to sent by WiFi LMAC
2. Fix the bug that AddBA request retrys too frequently
3. Forbid BA session setup for VO queue related TID
1. remove use EID to distinguish psram voltage
2. 1V8 64Mbit psram and 3V3 64Mbit psram use the same psram driver(standard spi interface)
3. set cs hold time register as 1
Content-Length header should not be included when using chunked encoding.
Some browsers will close the socket after seeing the 0 sized response instead of
reading the chunks.
Merges https://github.com/espressif/esp-idf/pull/2458
1. Add command for Ethernet based on console component.
2. Make cmd_system and iperf a component that can be referenced by other examples
3. Add "version" command to cmd_system.c
4. Clean up the README.md in all ethernet examples[TW#26525]
Added a new API esp_tls_set_global_ca_store(esp_tls_cfg_t *cfg) which creates a global_cacert which can be used by multiple connections by setting the use_global_ca_store variable to true in their respective structure of esp_tls_cfg_t. Also changed the cacert in the structure of esp_tls_t to a pointer.
* BLE and softAP provisioning examples added along with tests.
* An application specific example added for demonstrating custom provisioning scheme.
* tools/esp_prov/esp_prov.py can be used as a provisioning client for SoftAP, BLE and CLI based transports.
Co-Authored-By: Amey Inamdar <amey@espressif.com>
Co-Authored-By: Anurag Kar <anurag.kar@espressif.com>
* This manages secure sessions and provides framework for multiple transports.
* The application can use protocomm layer directly to have application specific extensions for provisioning (or non-provisioning) use cases.
* Following features are available for provisioning :
* Security - Security0 (no security), Security1 (curve25519 key exchange + AES-CTR encryption)
* Proof-of-possession support for Security1
* Protocomm requires specific protocol buffer modules for compilation which can be generated from the `.proto` files in the `proto` directory using make.
Co-Authored-By: Amey Inamdar <amey@espressif.com>
Co-Authored-By: Anurag Kar <anurag.kar@espressif.com>
tcp_transport component used public header files such as 'transport.h', etc. which are too generic and might collide with user or user libraries headers
This change closes#2417
In some cases, linker could choose to use ROM functions instead of the
ones defined in IDF.
For functions used in ROM stub table, this would lead to infinite
recursion when the corresponding function was called from ROM.
For crypto functions, some of these were modified in IDF, and
incompatible with ROM counterparts.
Problem Description
The reporduce steps are as follows:
1. put more than one same ssid AP in the environment;
2. set the STA mac address in one of the APs blacklist, and make sure the AP is closest to STA;
3. set the scan method in station config as all channel scan;
4. try to connect the AP which set STA in blacklist
Phenmenon
STA fail to connect after send auth or assoc with a wrong status code, but no disconnect event report and can not connect the next one in the envrionment
Root Cause
Because there are some same ssid APs in the evnrionment, when do all channel scan, it will collect all the matched AP in rc list, because rc list is not empty, so it would send disconnect event, however, we didn't do other step such as connect to other one
VNC MR 570
closes https://github.com/espressif/esp-idf/issues/2323
_rtc_data_{start,end} can now describe data placed into RTC_FAST
segment, if CONFIG_ESP32_RTCDATA_IN_FAST_MEM is enabled.
Use new _rtc_slow_length symbol instead.
When CONFIG_ESP32_RTCDATA_IN_FAST_MEM is enabled, RTC data is placed
into RTC_FAST memory region, viewed from the data bus. However the
bootloader was missing a check that this region should not be
overwritten after deep sleep, which caused .rtc.bss segment to loose
its contents after wakeup.
set shorter time to save some space on server. For those artifacts need
to be stored for long time, we can manually press "keep" button in job page.
Also add a CI job to check if all artifacts have set expire time.
fix the bug following:
1. after disable bluetooth controller, wifi cannot TX/RX any packets.
2. when software coexist working, there's a little ratio cause wifi task watchdog timeout
3. when software coexist working, there's a little ratio cause bluetooth cannot receive anything.
feature:
1. add libbtdm_app.a git commit local and remote checking
Known issues:
1. there's still a bug occurs with a very very low ratio cause bluetooth
cannot receive anything. The reproduce interval may great than 3days ~ 1week via
7x24 hours heavy testing.
Previously, esp-touch only supports multicast packets which are
transmitted from cellphone. But for most dual frequency routers
whose SSIDs of 5G and 2.4G are the same, broadcast packets are
forwarded from 5G interface to 2.4G interface while multicast
packets are not. In order to make esp-touch work when cellphone
connects to 5G interface of these routers, esp-touch is improved
to support both multicast and broadcast packets. Meanwhile, new
APP which is compiled with Andriod or IOS library(>= v0.3.6.2)
must be used in this situation. Note that for some routers,
broadcast and multicast packets are forwarded from 5G interface
to 2.4G interface only when another WiFi device is connected to
2.4G interface of the router. Old APP which is compiled with
Android or IOS library(< v0.3.6.2) also works with this improvement
when cellphone connects to 2.4G interface of the router.
The Android and IOS library of new esp-touch APP is now available
on Github.
Android: https://github.com/EspressifApp/EsptouchForAndroid
IOS: https://github.com/EspressifApp/EsptouchForIOS
Four internal APIs `esp_http_client_connect()`, `http_client_prepare_first_line()`, `esp_http_client_request_send()` and
`esp_http_client_send_post_data()` API have been added for perfoming connection establishment (sync as well as async),
preparing first line, sending request and sending post data respectively.
In `transport_ssl`, `ssl_connect_async()` API has been added for establishing asynchronous connection.
1. suppport mesh type, mesh ID, router and IE crypt func&key at any time after mesh is initalized.
2. support modify parent at any time after mesh is configured.
3. modify manual networking example.
4. update header file.
5. fix issues in root conflicts handling.
6. add max length of beacon to menuconfig.
7. fix issue when received a beacon without DSSS.
This introduces the following changes :
* Implmentation added for pthread attribute related functions :
* pthread_attr_init
* pthread_attr_destroy
* pthread_attr_setdetachstate
* pthread_attr_getdetachstate
* pthread_attr_getstacksize
* pthread_attr_setstacksize
* pthread_create now supports passing attributes/configs through pthread_attr_t structure
* pthread_mutex_timedlock added
* pthread_exit added
* memory for joinable thread is freed before returning from pthread_join
Problem Description
set some of routers as the same ssid in the same channel, when 32 in the fast scan connect mode, there may no disconnect event report in that two sceanrio:
1. set the correct password and connect, if target router didn't report 32's auth req before timeout, the state machine change to init but no disconnect event report
2. set a wrong password, if router send disassoc or deauth after run, rather than wait 4 way handshake timeout, the state machine change to init but no disconnect event report
Root Cause
Because the routers are in the same channel, all of them are matched the ssid, so all of them can be instore in the rc list wait for connect, when the first one want to connect fail at auth or receive
disassoc or deauth when password wrong, the rc list is not empty, it can not send disconnect event because rc is not empty
Solution
1. put the fail the router in the blacklist
2. Judge whether there is another router can be connect, if it has, try to connect with the next one
VNC MR 561
gen_esp_err_to_name.py includes files like
components/lwip/include/apps/esp_ping.h as "apps/esp_ping.h" because all
subdirectories of "include" are used. If "components/lwip/include/apps"
is in the path of the compiler instead of "components/lwip/include" then
include "apps/esp_ping.h" will fail. This fix allows to process lines
like:
'// gen_esp_err_to_name.py: some text "esp_ping.h" some text'
in header files for overwriting the include.
Before LwIP was moved into a submodule, sntp and esp_ping were
available as the following includes:
#include "apps/sntp/sntp.h"
#include "esp_ping.h"
This commit makes header files available at the old location, and adds
a deprecation warning for sntp.h.
Closes https://github.com/espressif/esp-idf/issues/2392
The lwip code didn't create an new mld group when netif is up,
this will lead to the server can't find the matching netif when
receiving NS(neighbor solicitation) packet
If exception support is disabled in IDF, and libstdc++ tries to throw
an exception, it will call __cxa_allocate_exception which is replaced
with abort in IDF.
We have a dramatically size reduction of the RO-section in binary when using '__throw_'-stubs in GCC5
In the case of using GCC8, we are faced with 'multiple definition' errors when using '__throw_'-stubs.
Good that we don't have the size problem due to gcc8
If CONFIG_FREERTOS_LEGACY_HOOKS is kept enabled then defining
idle/tick hooks will be applications responsibility as was the
case earlier.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
1. create a new pbuf to squash linked pbuf
2. optimize emac driver by adding ESP_IRAM_ATTR
3. remove duplicated function declare in esp_eth.h
4. remove duplicated code in emac_setup_tx_desc
5. disable Promiscuous mode
1. Keep awake to receive beacon at TBTT time no matter which state
station is on.
2. If there is any packet to send on dream or sleep state, send NULL
data with power save bit clear first.
This commit adds an option to enclose all FreeRTOS task functions within a
wrapper function. In the case that a task function returns, the wrapper function
will log an error and abort the application immediately.
Closes#2269Closes#2300
refence to https://github.com/espressif/esp-idf/issues/2284
Before fixing, the tx power in adv data is always 0xeb(-21dbm).
restriction:
If change BLE advertising TX power, please call esp_ble_gap_config_adv_data()
after BLE adv TX power changed.
Later, will implement set BLE advertising TX power via HCI, then the
TX power value in adv data can be update automatically after BLE adv
TX power changed.
Changes:
KConfig: The option CONFIG_ESP32_RTCDATA_IN_FAST_MEM is added in Kconfig file for esp32 component.
esp32.common.ld: added support of RTC_DATA_ATTR, RTC_RODATA_ATTR data placement into appropriate segment according to Kconfig option.
esp32.ld: linker script is modified to set alias for memory segment selected by Kconfig option to place data. The segments for force placement are added for RTC_FAST_ATTR, RTC_SLOW_ATTR attributes.
esp_attr.h: added new attributes RTC_FAST_ATTR, RTC_SLOW_ATTR for force placement into fest/slow memory.
test_rtc_fast.c: Added unit test cases to check data placement into appropriate memory segment.
Updated documentation for RTC_DATA_ATTR, RTC_FAST_ATTR, RTC_SLOW_ATTR in deep_sleep_stub.rst file.
TW#18001
Closes https://github.com/espressif/esp-idf/issues/1553
added docs and tests for mqtt library, small fixes (removed warnings, option for custom outbox, websocket bug fixed for longer transports). refactored to use common tcp_transport component, support for CMake build system.
Closes#2108
Allocation was happening later, causing possible use of stack variables
of caller function, which could be invalid.
Signed-off-by: Piyush Shah <piyush@espressif.com>
Using 'sudo pip install' can cause a lot of problems because usually
there are a couple of Python interpreters installed. This fix encourages
developers to use `pip install --user` instead which is safer.
On some systems pip and setuptools are no longer installed as
dependencies of the python packages. This commit adds the requirement
for these packages.
AVRCP connection binds to A2DP in current implementation, despite the two profiles are\
independent according to specification. AVRCP connection is not necessary to set-up \
if A2DP connection fails to establish
In opening state of AVDTP connection, if SDP client fails to get valid A2DP service record\
from peer SDP server, then do not initiate AVDTP connection request
In pevious implementation, A2DP sink will register an A2DP source Stream End Point(SEP) although the SEP is not\
supposed to be used. Now remove the unused SEP for source so that only one role of A2DP can be supported at one
time. Service record in local SDP server only includes at most one service for A2DP sink role or source
1. In original driver, the stack size for emac driver task "emacT" is only 2048 Bytes, which also can not be changed by user.
2. Each time when invoking "emac_start" function, it will reset emac registers, the driver should reconfig some important registers again.
* Fixed regex constraints for parsing IP and other parameters from monitor log.
* httplib connection timeouts set
* Redundent tests (commented out earlier) have been removed from advanced_tests. These tests are already run during unit testing.
Currently CI test environment is complicated, usually includes NIC, AP.
These devices are not used for a lot test cases. Therefore we split the
test environment, remove unnecessary devices. Then it will be easier to
create CI runners.
As the bluedroid original implmentation of BR/EDR and BLE dual mode about discovery mode,
when set discovery mode for BR/EDR, it will stop ble advertising.
Reference to https://github.com/espressif/esp-idf/issues/2306
The following commit rewrites the ESP-MESH docs. This commit includes
new diagrams and a structure approach to the mesh docs. Some mesh api references
have also been modified.
This commit does the following
- Add power management lock to CAN driver so that APB frequency does not change
whilst CAN driver is in use
- Fix incorrect flag in can_transmit()
- Refactor can_driver_install() and can_driver_uninstall() so that critical sections
are shorter
- Fix CAN gpio configuration bug on RX pin. Closes#2302
- Add docs about multiple ID configuration and fix example links
Problem:
The new API esp_bt_mem_release() that was added freed BTDM data to heap from esp_bt_controller_mem_release().
Now with the BT memory optimization commit ee787085f9,
the BTDM data is optimized and reduced to only 32 bytes which is not sufficient amount to be added to heap.
So, using the API leads to assert saying that the region is too small.
Solution:
Modify heap_caps_add_region_with_caps to return ESP_ERR_INVALID_SIZE in case the range is too small to create a new heap.
Do not assert if return value is ESP_ERR_INVALID_SIZE
This also fixes using API esp_bt_controller_mem_release() with ESP_BT_MODE_BTDM
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
Guarantees that a component's project_include.cmake will be called after its dependent components'
project_include.cmake. Because of cycles in the dependency graph, this is less useful than you'd
think but it gives a strong guarantee for any component which is not part of a cycle.
Also applies deterministic ordering (ordering is initialised as COMPONENT_REQUIRES_COMMON then all
COMPONENTS in alphabetical order, but then the sorting by dependencies is applied.)
Eclipse was unable to resolve the std::mutex type eventhough the mutex header file was succesfully included. By adding this modification, the issues was resolved.
Some APs transmit AMPDU and MPDU by turns. Moreover, the sequence
numbers of AMPDU and MPDU are out of order, e.g. MPDU(1253) -
AMPDU(1251, 1252) - MPDU(1254) - AMPDU(1255, 1256). In order to
receive both AMPDU and MPDU in order, MPDU must be reordered with
AMPDU.
1. New tests for SD card on slot 0. Currently frequency for 4-bit mode
has to be reduced in the test.
2. Change pin for CD/WP tests, re-enable CD tests.
Works for 3.3V eMMC in 4 line mode.
Not implemented:
- DDR mode for SD cards (UHS-I) also need voltage to be switched to 1.8V.
- 8-line DDR mode for eMMC to be implemented later.
This introduces the following changes in the example test scripts :
* Dependency on python requests library removed in favor of httplib
* Bug fixed in the logic responsible for receiving and processing http chunked responses
* Default timeouts increased Note : Due to connectivity issues (between runner host and DUT) in the runner environment, some of the advanced_tests are being ignored. These tests are intended for verifying the expected limits of the http_server capabilities, and implement sending and receiving of large HTTP packets and malformed requests, running multiple parallel sessions, etc. It is advised that all these tests be run locally, when making changes or adding new features to this component.
It is possible to utilize some of the routines related to otadata
partition validation, after firmware image is downloaded to RAM. Hence
these routines should be part of app cpu cache, so that they do not
get overwritten by firmware.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
Allows OTA updates to be secured via signature checks, without requiring the overhead or complexity
of a full secure boot implementation.
Uses same signing mechanisms (build system and/or espsecure.py as Secure Boot).
Requires:
* [ ] More testing
* [ ] Documentation
Fixes mismatches where default Python interpreter may not match the most recently
installed sphinx-build wrapper script (if sphinx 2 & 3 both installed, pip will
clobber any previous copy of /bin/sphinx-build when it installs the new one.)
res was declared as “bool” so expression
((count == 0) ? A2D_SET_ONE_BIT : A2D_SET_MULTL_BIT)
always evaluated to “true”, and was implicitly converted to
A2D_SET_ONE_BIT.
Avoids growing the result of hardware bignum operations
(particularly for multiplication)
Fixes bugs where some Elliptic Curve operations fail or corrupt memory,
as they assume length of the number is never greater than the number of
non-zero limbs.
Includes some general refactoring to standardize terminology.
Closes https://github.com/espressif/esp-idf/issues/1556
Fixes TW12984
Adds test cases for both these issues.
1. after memory release MR merged, due to the get acl number condition is not completed, it will cause get acl number value incorrect
2. It may cause set Security Mode (BR/EDR) enable failed
1. change static emac-dma memory to dynamic
2. add esp_eth_deinit
3. modify ethernet example
4. add testcase for ethernet deinit function
5. GPIO0 could not output the 50MHz clock to PHY, so remove this configuration
1. new APIs: esp_mesh_get_subnet_nodes_num() and esp_mesh_get_subnet_nodes_list().
2. fix hard to find the parent during connect.
3. disable Wi-Fi channel switch function.
4. fix a typo of MESH_EVENT_NO_PARENT_FOUND.
esp_reset_reason_init would check for reset reason hint, and
unconditionally set RTC_RESET_CAUSE_REG (which is also
RTC_ENTRY_ADDR_REG) to hint value 0, i.e. 0x80000000. However the ROM
code treats this value as valid deep sleep wake stub entry point, and
tries to jump to it.
Clear RTC_RESET_CAUSE_REG only if it contained a valid reset reason
hint, and simply set the register value to 0 when doing so. Also add
a check to esp_get_deep_sleep_wake_stub function that deep sleep wake
stub entry address must be in IRAM.
Reported in https://esp32.com/viewtopic.php?f=13&t=6919.
Fix following WiFi bugs:
1. Shouldn't scan when connect
2. Check beacon length in modem sleep
3. Fix the bug that AP may deauth wrong station when inactivity timer expires
4. Fix the bug that WiFi assert the system when receiving empty MCS in association response frame
Multiple modules register their callback BTA_GATTS_AppRegister().
If any of the callbacks do not free the allocated pointer in
BTA_GATTS_CONF_EVT event, then this can result in memory leak.
So, free the pointer after the callback function is called and remove
the calls to free in the callback functions as it is now not required
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
This is just a quick glance at all the header files exposed to the
users from cleanup point of view.
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
We have fixed a bug in test script. Before that, we didn't do strict check when generate the mesh tree, which makes the test pass.
Temp disable these cases, to let CI pass before bug fixed.
When 32k XTAL was selected as clock source, if the first calibration
attempt failed, the code would fall back to 150kHz internal clock.
Calibration with the internal clock will always succeed.
Therefore `wait` would always be either 0 or 1. Based on this, some
code in this routine can be eliminated.
Marking a page full does not skip it from page selection process and the
same page might get returned if there is no other page with more unused
entries. Added a check for the same while storing blobs.
Fixes: https://github.com/espressif/esp-idf/issues/2313
Previous APIs used to set CPU frequency used CPU frequencies listed in
rtc_cpu_freq_t enumeration. This was problematic for two reasons.
First, supporting many possible frequency values obtained by dividing
XTAL frequency was hard, as every value would have to be listed in
the enumeration. Since different base XTAL frequencies are supported,
this further complicated things, since not all of these divided
frequencies would be valid for any given XTAL frequency. Second,
having to deal with enumeration values often involved switch
statements to convert between enumeration and MHz values, handle
PLL/XTAL frequencies separately, etc.
This change introduces rtc_cpu_freq_config_t structure, which contains
CPU frequency (in MHz) and information on how this frequency has to
be generated: clock source (XTAL/PLL), source frequency, clock
divider value. More fields can be added to this structure in the
future. This structure simplifies many parts of the code, since both
frequency value and frequency generation settings can be accessed in
any place in code without the need for conversions.
Additionally, this change adds setting of REF_TICK dividers to support
frequencies lower then XTAL with DFS.
`esp_http_client_write` API puts a constraint on the maximum length of the data that can be
written, which is equal to client handle buffer size, but the data to be sent can be more
than that, so in this case, this API has to be called multiple times.
In `esp_http_client_open` API, the return value of `transport_write` API, used to send HTTP
request, is not checked, and in rare cases, data written will be less than expected which will
cause a problem. So there are fixes for these minor issues in this MR.
Calling `esp_bt_controller_mem_release` or `esp_bt_mem_release` might result in exception if any of the regions returned to heap are empty. This happens usually if BT/BLE is enabled, but not used/linked in the final firmware.
1. BLE only with 9(max) connection will decrease 3K DRAM
2. BR/EDR only with 7(max) connection will decrease 16K DRAM
3. Any of BLE or BR/EDR connection number decrease will also decrease DRAM consumption
4. Decrease one BLE connection will save about 1KB DRAM
5. Decrease one BR/EDR ACL connection will save about 1.2KB DRAM
6. Decrease one BR/EDR SCO/eSCO will save 2KB DRAM.
7. fix some definition and kconfig
8. remove 1.2k of vhci tx cache and make .bss & .data to heap about 1.4K
9. modify BT Reserved Memory size and modify example to support new bt kconfig
Hardware implements conditions LE, LT, GE, and conditions EQ and GT
are implemented in the assembler by emitting two JUMPS instructions
with other conditions.
Added bootloader_common_get_sha256_of_partition() and esp_partition_get_sha256() - get or calculate SHA-256
digest for app and data partitions.
Added bootloader_sha256_hex_to_str() - helps to print SHA-256 digest
Added esp_partition_check_identity() - compares two partitions by SHA-256 digest
Refactoring a function esp_image_load() in bootloader space to esp_image_verify() and
bootloader_load_image(). Old name function esp_image_load is deprecated
and will remove in V4.0 version.
spi_flash/sim: Fix error test_host. Add stub for bootloader_common_get_sha256_of_partition in sim/stubs
1. Add the 100 times test when the private key is generated by the random number;
2. Add the bt components to the unit-test-app/config directory.
3. Added the bt unit test case to CI.
For pins 32 and up the BIT(nr) macro used here overflowed,
causing undetermined GPIO pins to be reset.
Example: freeing SPI device/bus where CS is on pin 33
caused debug UART to cease communication, TXD0 was
disabled.
Fixed as BIT64(nr) macro, to be used elsewhere as needed.
For example in definitions like GPIO_SEL_32..GPIO_SEL_39.
1. modify parent switch mechanism.
2. fix non-root doesn't clear the layer value in nvs.
3. fix retransmit the remove announcement packets.
4. add API esp_mesh_flush_upstream_packets().
5. automatically adjust passsive scan time based on the change of beacon interval.
Component which includes component_ulp_common.mk may also need to set
some of the same COMPONENT_XXX variables. Logically, we should combine
the lists of files to embed, ldflags, extra include dirs, etc.
Fixes https://github.com/espressif/esp-idf/issues/2157.
The argument to ulp_run should be expressed in 32-bit words. Both the
address of ulp_entry and RTC_SLOW_MEM already are uint32_t*, so their
difference is the difference in addresses divided by sizeof(uint32_t).
Therefore the extra division by sizeof(uint32_t) is not needed.
1. The test step for error code REASON_ASSOC_EXPIRE is not reliable. SoftAP
could also send error code WIFI_REASON_NOT_AUTHED
2. STA will be disconnected now if softAP restart DHCP server
* "git clone" command and a small version header are generated
depending on git properties.
* Add Versions page with details about each version
* Make it clear using master branch is living on the "bleeding
edge"
No longer necessary to keep all reserved addresses in 'soc'.
Means 'soc' does not need to know about 'bt', for example.
Also means that Bluetooth can be enabled in config without any memory being reserved for BT
controller. Only if code calling the BT controller is linked in, will this memory be reserved...
This change adds a check for compatibility between the nvs version
found on nvs flash and the one assumed by running code during nvs
initialization. Any mismatch is reported to the user using new error
code ESP_ERR_NVS_NEW_VERSION_FOUND.
Update libphy.a to v3960:
1. Decrease phy_init time from 900us to 347us in sleep wakeup
2. Fix RX STBC initialization
3. Modify set_chan function to fix interrupt watchdog issue
it will resolve the problem:
1. when bluetooth is running (For example: a2dp sink), wifi station cannot connect to AP easily
2. improve wifi connection success ratio when coexist is working
Based on report on forum here:
https://esp32.com/viewtopic.php?f=13&t=6382&p=27514
Previous versions were much more relaxed about what could be in the partition
table, erroring out avoids unexpected changes on upgrade like different
partition offsets.
- A bug of the http client when it downloads a chunked encoding packet is greater than the http_client's buffer, http_parser will call the callback body more than once, and the client will only handle the last
- with ssl_read, need to check before read to avoid timeout blocked when no data for reading
* spi_flash_mmap_pages needs pages array to be in internal memory.
Document and check this.
* Fix a bug that spi_flash_mmap did not allocate pages array in
internal memory.
* Minor style fixes: const-ify pages argument of spi_flash_mmap, add
spaces around operators, mark output arguments with [out].
Closes https://github.com/espressif/esp-idf/issues/2229.
The test is previously disabled for the requirement of external
connection. Now the signals are connected by internal connections.
Also change the failure logic of the test.
Fixed problem with multiple mount/unmount for different devices.
Additional check for structure length included into the code.
Remove useless spaces.
Added initialization for reserved memory.
WL version 2 mark used sectors as 16 bytes block of bytes with CRC.
This changes required because old version did not worked with encryption.
Additional unit tests are implemented.
End handle is incorrectly printed as start handle
Tested that gatt_client, gatt_security_client and gattc_multi_connect compile successfully
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
Add a command `make erase_ota` - erases otadata if it there is in the
partition table otherwise error 'Partition table does not have ota_data partition'.
Closes https://github.com/espressif/esp-idf/issues/1821
heap_caps_malloc will fail to poison a block in IRAM with size not
divisible by 4. The proper fix will be to make poisoning code
smarter, or to disallow allocations from IRAM with size not aligned
by 4.
If project.mk is included twice in recursive invocation of Make, some
variables defined on the first pass will not be redefined on the
second pass. Rather than cleaning up these variables before calling
Make recursively, don’t include IDF project.mk at all, if one of the
ut- targets is requested.
If we have the partition table without any ota_apps but in ota_data have
valide entry, in this case we get an error(hang). This commit fix this
case. If bs->app_count is zero when selecting the factory app.
Closes https://github.com/espressif/esp-idf/issues/2218
1. when one task do deinit/init/disable/enable, especially different cpu
core, it may cause controller crash in ISR handler
2. fix while BLE is scanning, bluetooth controller is disabled cause BLE
scan is not abort.
1. Modify esp_bt_controller_mem_release() to release BTDM BSS and Data to heap if
ESP_BT_MODE_BTDM mode is passed to it
2. Add a new API esp_bt_mem_release() which internally calls
esp_bt_controller_mem_release() with the provided mode and then if mode
is ESP_BT_MODE_BTDM, releases BT BSS and Data to heap.
Background:
For Wi-Fi and BT/BLE applications, for e.g. the usecase is like when
Bluetooth is used for provisioning and once the device is connected to the Wi-Fi
AP, we can turn off Bluetooth completely. In such scenarios, it should be possible to
reclaim all the memory of Bluetooth. Although, currently this does not
happen.
Experiment:
Made the following modifications to examples/bluetooth/gatt_server :
1. Added support of simple_wifi to it
2. Moved all the bluetooth related code under CONFIG_BT_ENABLED config
option
3. Calculated the free heap in 2 similar scenarios:
i. Disabled BT (CONFIG_BT_ENABLED undefined) and checked the free
heap after STA connected
ii. Kept BT enabled and disabled it after STA connected and checked
the free heap
Ideally, the numbers for i., ii. above should have been similar. But
there was a delta of almost 30-31K. (i. > ii.)
4. Through make size-components checked the common BSS for libbta.a and libbtdm_app.a
and found it to be almost 30K. Data is around 1K
Solution:
1. Modified the linker script to mark the BSS and Data for these libraries and
free it when ESP_BT_MODE_BTDM mode is passed to mem release APIs.
2. Verified that the free heap is comparable for i. and ii. above.
Note: It is known that once this is done, Bluetooth can only be used
again post reboot.
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
This change removes the earlier limitation of 1984 bytes for storing data-blobs.
Blobs larger than the sector size are split and stored on multiple sectors.
For this purpose, two new datatypes (multi-page index and multi-page data) are
added for entries stored in the sectors. The underlying read, write, erase and find
operations are modified to support these large blobs. The change is transparent
to users of the library and no special APIs need to be used to store these large
blobs.
* Fixes some "noreturn" functions in bootloader utils which did return (causing fatal CPU
exceptions).
* Marks bootloader entry as "noreturn", preventing "user code done" from stalling boot
Partial fix for https://github.com/espressif/esp-idf/issues/1814 TW20016
(Comprehensive fix for this issue will be enabling WDT during bootloader, coming shortly.)
1. Move channel to the first row of the table.
2. Remove the condition of HT20/HT40 for they are determined by
secondary channel.
3. Clean up the CSI table.
Because address space is mapped in 64KB pages, it was possible for unauthenticated data after the
app .bin to become mapped into the flash cache address space.
This problem is solved by 2 changes:
* "esptool elf2image --secure-pad" will pad the image so that the signature block ends close to the
64KB boundary. Due to alignment constraints it will be 12 bytes too short after signing (but
with flash encryption, these 12 bytes are still encrypted as part of the last block and can't be
arbitrarily changed).
* By default, secure boot now requires all app partitions to be a multiple of 64KB in size.
- call rtc_gpio_init for pins which aren't configured as RTC by default
- for RTC IOs 16 and 17, read higher part of the input register
- automatically convert GPIO number into RTC IO number
- use ulp_set_wakeup_period instead of writing to register
We found some SD card on Raspberry Pi could have very bad performance.
It could take seconds to save small amount of data.
If the DUT receives data and save it as log, then it stops receiving data until log is saved.
This could lead to expect timeout. As an workaround to this issue,
``BaseDUT`` class will create a thread to save logs.
Then data will be passed to ``expect`` as soon as received.
Perviously host send_auto_stop flag would be set for every data
transfer over 1 block long. This caused stop commands to be sent
after CMD53, which shouldn't be done. Fix by adding an explicit list
of commands for which send_auto_stop should be set.
Send the Goodbye packet while removing an mDNS service as an "Authoritative" packet so
that the listeners remove the service from their records immediately.
Fixed the error division on zero.
Also fixed range CONFIG_ESP32_RTC_CLK_CAL_CYCLES in Kconfig.
Fixed a overflow error by TIMG in the function rtc_clk_cal_internal. This error was due to a limit in values TIMG_RTC_CALI_MAX=0x7FFF (to write the slowclk_cycles) and TIMG_RTC_CALI_VALUE=0x1FFFFFF (to read xtal_cycles). Added assert finctions.
Closes https://github.com/espressif/esp-idf/issues/2147
1. Add reading psram EID.
2. Configure different clock mode for different EID.
3. add API to get psram size and voltage.
4. Remove unnecessary VSPI claim.
For 32MBit@1.8V and 64MBit@3.3V psram, there should be 2 extra clock cycles after CS get high level.
For 64MBit@1.8 psram, we can just use standard SPI protocol to drive the psram. We also need to increase the HOLD time for CS in this case.
EID for psram:
32MBit 1.8v: 0x20
64MBit 1.8v: 0x26
64MBit 3.3v: 0x46
The WiFi station connect sequence diagram does not have any "successful" ending.
It looks like a copy-paste error, because there are two consequent `SYSTEM_EVENT_STA_DISCONNECTED` events firing with nothing happening in between.
I think the original meaning was that the last event should be `SYSTEM_EVENT_STA_CONNECTED` to signify that if all goes well, that is the event that will be fired.
Merges https://github.com/espressif/esp-idf/pull/2065
When 2nd stage bootloader loads the ROM bootloader, it prints a
message similar to "entry 0x40080xxx", which idf_monitor decodes
(using application ELF file) as one of the reset vectors (xxx is <
400h). This moves the iram_seg of bootloader 1k up to prevent overlap
of bootloader .text and application vectors, making the output look
nicer. There is still a chance that the entry point decodes as some
symbol in application ELF file, but at least it won't have
"Exception" in its name.
Since 94250e42a0, UART output is suspended when entering sleep mode
(deep or light sleep). This makes sense for light sleep, where sleep
normally takes small amount of time, and flushing the UART would add
a lot of latency. But this breaks existing behaviour for deep sleep,
where UART output was previously sent out before entering sleep mode.
Closes https://github.com/espressif/esp-idf/issues/2145
remote_ip was declared to be a pointer to an address that was
overwritten in later stage thus changing the address pointed by remote_ip
esp_smartconfig.h : Fixed a typo. station_config to wifi_config_t
Signed-off-by: Sachin Parekh <sachin.parekh@espressif.com>
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
uart.c/h: fix param errors
test_uart.c: Remove GCC warning supress
uart.rst: fix the notes
rs485_example.c: fix output
uart.c: remove reset using UART_RXFIFO_RST from driver.
readme.md: Update example description
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
uart.c/h: fix param errors
test_uart.c: Remove GCC warning supress
uart.rst: fix the notes
rs485_example.c: fix output
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
uart.c/h: fix param errors
test_uart.c: Remove GCC warning supress
uart.rst: fix the notes
rs485_example.c: fix output
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
test_uart.c remove ignore tag
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
update uart.h (uart_set_rx_timeout() description
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
An existing UART driver does not support RS485 half duplex mode.
This task adds this functionality to ESP_IDF UART driver.
driver/uart.c/h: updated to add support of RS485 half duplex mode
examples/peripherals/uart_echo_rs485/main/rs485_example.c: added test example
components/driver/test/test_uart.c: added test of RS485 half duplex mode
docs/en/api-reference/peripherals/uart.rst: updated documentation
test_uart.c: suppress GCC warnings about discarded const qualifiers
uart.rst: remove sphinx warning - "Duplicate explicit target name"
simple change in uart.h file
update (test_uart.c) after rebase from master
update uart.rst, uart.c, rs485_example.c
Update example description in file Readme.md
update uart.c/h, uart.rst, test_uart.c according to review results
The tests are completed using RS485 adapters hardware connected to two ESP32 WROVER KITs.
TW#13812
Closes https://github.com/espressif/esp-idf/pull/667
Closes https://github.com/espressif/esp-idf/pull/1006
components/wpa_supplicant/port/include/os.h:259:29: error: 'strncpy' output truncated before terminating nul copying 3 bytes from a string of the same length [-Werror=stringop-truncation]
#define os_strncpy(d, s, n) strncpy((d), (s), (n))
^~~~~~~~~~~~~~~~~~~~~~
components/wpa_supplicant/src/wpa2/eap_peer/eap.c:410:3: note: in expansion of macro 'os_strncpy'
os_strncpy(sm->blob[0].name, CLIENT_CERT_NAME, BLOB_NAME_LEN);
^~~~~~~~~~
components/spi_flash/partition.c: In function 'load_partitions':
components/spi_flash/partition.c:179:66: error: argument to 'sizeof' in 'strncpy' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
strncpy(item->info.label, (const char*) it->label, sizeof(it->label));
^
components/fatfs/src/ff.c: In function 'f_fdisk':
components/fatfs/src/ff.c:5995:5: error: this 'for' clause does not guard... [-Werror=misleading-indentation]
for (n = 16; n < 256 && sz_disk / n / cluster_size > 1024; n *= 2) ;
^~~
components/fatfs/src/ff.c:5996:2: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the 'for'
if (n == 256) n--;
^~
components/esp32/ipc.c: In function 'esp_ipc_init':
components/esp32/ipc.c:82:31: error: '%d' directive writing between 1 and 11 bytes into a region of size 5 [-Werror=format-overflow=]
sprintf(task_name,"ipc%d",i);
^~
components/esp32/ipc.c:82:27: note: directive argument in the range [-2147483648, 1]
sprintf(task_name,"ipc%d",i);
^~~~~~~
components/esp32/ipc.c:82:9: note: 'sprintf' output between 5 and 15 bytes into a destination of size 8
sprintf(task_name,"ipc%d",i);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
INTERRUPT and CCOUNT registers will change outside of program control.
Making the inline assembly used to read these registers volatile
indicates this fact to the compiler.
Fixes https://github.com/espressif/esp-idf/issues/2127
coap client parse a string by `coap_split_uri`,fetch host should by `host.length`
otherwise, would cause `gethostbyname` failed because of inappropriate parameter.
The fix is for the situation when cache disabling mechanism causes
a deadlock with user tasks. Situation is as follows:
1. spi_flash operation is started from low-priority task on CPU0
2. It uses IPC to wake up high-priority IPC1 task on CPU1, preventing
all other tasks on CPU1 from running. This is needed to safely
disable the cache.
3. While the task which started spi_flash operation is waiting for IPC1
task to acknowledge that CPU1 is not using cache anymore, it is
preempted by a higher priority application task ("app0").
4. Task app0 busy-waits for some operation on CPU1 to complete. But
since application tasks are blocked out by IPC1 task, this never
happens. Since app0 is busy-waiting, the task doing spi flash
operation never runs.
The more or less logical soltion to the problem would be to also do
cache disabling on CPU0 and the SPI flash operation itself from IPC0
task. However IPC0 task stack would need to be increased to allow doing
SPI flash operation (and IPC1 stack as well). This would waste some
memory. An alternative approach adopted in this fix is to call FreeRTOS
functions to temporary increase the priority of SPI flash operation task
to the same level as the IPC task.
Fixes https://github.com/espressif/arduino-esp32/issues/740
Fixes https://github.com/espressif/esp-idf/issues/1157
1. fix BLE connection missing in coex mode
2. modify other parameters to make coex priority more reasonable
3. fix modem sleep procedure trap cause Wifi disable RF when BT is
working. Such cause that BR/EDR is difficult to be connected, BLE
connection stability decrease and so on.
4. modify BR/EDR coexist duration to imrove BR/EDR connect success
ratio.
5. Due to the hardware coexist bug, BLE scan interval/window should
be less than 0x100(about 160ms). Therefore, it will cause BLE cannot
scan any advertising packet while WiFi have higher priority
behaviour(such like RX beacon, scan, TX/RX VO packets and etc.).
1. add APIs to set/get announce interval values.
2. add API to enable/disable the min rate to 6Mbps for data packages.
3. add APIs to set/get RSSI threshold values.
4. fix ap_loss.
Test report is not used as expected:
1. we rarely download and use test report
2. current test report method doesn't handle large amount data well,
need to be replaced by other methods
Test report also make test jobs allow to fail. It breaks the
original flow of Gitlab CI and make user confused.
Moved useful functions from wrapped assert functions, because option `CONFIG_OPTIMIZATION_ASSERTIONS_DISABLED=y` will remove this functions.
Closes https://github.com/espressif/esp-idf/issues/2068
1. esp_ble_remove_bond_device will only remove BLE bond key and disconnect BLE device.
2. esp_bt_gap_remove_bond_device will only remove BT bond key and disconnect BT device.
As reported https://esp32.com/viewtopic.php?f=14&t=6171
event_callback() in sockets.c calls conn->socket-- to register
activity on a netconn which may not have any socket yet,
so any socket value < 0 indicates "no controlling socket"
for the netconn.
51e42d8e92
introduced filtering options which handles the last (unterminated) line
with a delay. This introduced poor performance for console applications
when the user interacts with the ESP32 device in the same line because
there is an artificial delay for each key-press.
bb152030a0
decreased the delay but there are still delays for each key-presses.
The current fix makes only one delay per line instead of each
key-presses. When an unterminated line is detected then no more
"delayed" print is used for the given line.
Fixes https://github.com/espressif/esp-idf/issues/2054
IDF had two defines ESP_PARTITION_TABLE_OFFSET and ESP_PARTITION_TABLE_ADDR. They were the same and equal by 0x8000.
A define ESP_PARTITION_TABLE_ADDR was removed from IDF.
A define ESP_PARTITION_TABLE_OFFSET depends on option CONFIG_PARTITION_TABLE_OFFSET in Kconfig.
Now using only #define ESP_PARTITION_TABLE_OFFSET CONFIG_PARTITION_TABLE_OFFSET
This change allows readonly FATFS to be mounted without wear levelling
support. This will provide the customers a simple way to mount FATFS images
generated on host and flashed onto the chip during factory provisioning.
Since NVS encryption is not supported yet and NVS entry size is limited,
the change will provide an easy alternative for securing the provisioning data
by just marking FATFS parition as encrypted.
The IDF monitor waits for one second before printing the last
unterminated line. This is necessary for the correct filtering.
However, this causes poor performance, for example, in the case of the
system/console example.
This fix reduces the waiting time which improves the response time of
the console example and doesn't seem to influence the monitor filter.
Closes https://github.com/espressif/esp-idf/issues/2054
* a missing pointer increment caused error, if available was > 0 after the first iteration of while(available) loop.
* changed memory allocation strategy from large fixed size (RFCOMM_DATA_BUF_SIZE) to just the needed
size, which will be below MTU
Cherry-picked from https://github.com/espressif/esp-idf/pull/1923/
Since commit 94250e4, EXT0 wakeup mechanism, when wakeup level was set
to 0, started waking up chip immediately after entering deep sleep.
This failure was triggered in that commit by a change of
RTC_CNTL_MIN_SLP_VAL (i.e. minimum time in sleep mode until wakeup
can happen) from 128 cycles to 2 cycles.
The reason for this behaviour is related to the way input enable (IE)
signal going into an RTC pad is obtained:
PAD_IE = (SLP_SEL) ? SLP_IE & CHIP_SLEEP : IE,
where SLP_IE, SLP_SEL, and IE are bits of an RTC_IO register related
to the given pad. CHIP_SLEEP is the signal indicating that chip has
entered sleep mode.
The code in prepare_ext{0,1}_wakeup did not enable IE, but did enable
SLP_SEL and SLP_IE. This meant that until CHIP_SLEEP went high, PAD_IE
was 0, hence the input from the pad read 0 even if external signal
was 1. CHIP_SLEEP went high on the 2nd cycle of sleep. So when
RTC_CNTL_MIN_SLP_VAL was set to 2, the input signal from the pad was
latched as 0 at the moment when CHIP_SLEEP went high, causing EXT0
wakeup with level 0 to trigger.
This commit changes the way PAD_IE is enabled: SLP_SEL and SLP_IE are
no longer used, and IE is set to 1. If EXT0 wakeup is used, RTC_IO is
not powered down, so IE signal stays 1 both before CHIP_SLEEP goes
high and after. If EXT1 wakeup is used, RTC_IO may be powered down.
However prepare_ext1_wakeup enables Hold on the pad, locking states
of all the control signals, including IE.
Closes https://github.com/espressif/esp-idf/issues/1931
Closes https://github.com/espressif/esp-idf/issues/2043
For some test configurations, not all tests need to be run. This
change allows adding a comment in the configuration file of the
following form:
unit-test-app makefile will use it to determine which components to
build. If the comment is not present, all components will be built
(TESTS_ALL=1).
Also add test configuration for libsodium. It is a separate test
configuration due to the large binary size generated when building
libsodium tests.
Previously the loop in esp_timer_impl_set_alarm was necessary to catch
the case when timer count wraps around (goes from 2^32 - 1 to 0).
Since ALARM_OVERFLOW_VAL was reduced from 2^32 - 1 to 0xefffffff,
this is no longer necessary.
Fixes https://github.com/espressif/esp-idf/issues/1891
When ‘fetch’ strategy is used, Gitlab removes untracked files before
checking out new revision. However if the new revision doesn’t
include some of the submodules which were present in the old
revision, such submodule directories would not be removed by the
checkout. This extra step ensures that these stale submodules are
removed.
Allows you to move the partition table, it gives more space for the bootloader.
Added a new utility - parttool.py. This utility can search for the offset and/or size of the partitions by name and type/subtype. Use for getting APP_OFFSET and PHY_DATA_OFFSET.
The linker(esp32.bootloader.ld) made changes that allow you to write a custom bootloader code more.
TW14125
spi test: Prime the flash cache before each test to minimise flash cache misses.
VFS performance test: Increase the number of runs to minimise influence of an isolated bad run.
The old command caused was incorrect (x is “examine”, not “execute”)
and caused GDB register update only by chance. This replaces it with
“flushregs” command which purpose is exactly that — force GDB to
fetch registers from the remote.
Makes spiffs component runnable on host. Depends on the host library build
of flash emulator. Includes a basic sanity test of
mounting a volume, opening a file, writing to the file, reading the file,
closing the file and unmounting volume.
Makes fatfs component runnable on host. Depends on the host library build
of wear levelling and flash emulator. Includes a basic sanity test of
mounting a volume, opening a file, writing to the file, reading the file,
closing the file and unmounting volume.
Makes the entirety of the wl API runnable on host. Flash emulator
is separated into spi_flash component directory to be reused by
other storage components.
Before entering the deep sleep, the RTC and FRC counters are synchronized. Updating the boot_time.
Added a unit test for this case.
Fixed warnings for MULTIPLE_STAGES
Closes https://github.com/espressif/esp-idf/issues/1840
1. Fix the WiFi/BT coexist bug
2. Fix WPA2 enterprise example crash bug
3. Add size and version check for crypto type struct
4. Add MD5 check for crypto type header file
Added .rtc_noinit and .noinit section definitions into linker file /esp32/ld/esp32.common.ld.
The macro __NOINIT_ATTR, RTC_NOINIT_ATTR declared in esp32/esp_attr.h file.
Added unit test file to test added behavior for noinit variables and its attributes.
Added documentation changes for new added attributes.
Make some corrections after code review:
The linker file has been corrected to place noinit section before bss_start to make it safer.
Documentation file has been modified to clarify reset behavior of allocated data .
Corrected typos in test_noinit.c and removed assertion of noinit variable to avoid possible issues with ROM boot loader memory allocation.
The linker file has been corrected to place noinit section before bss_start to make it safer.
Documentation file has been modified to clarify reset behavior of allocated data .
Corrected typos in test_noinit.c and removed assertion of noinit variable to avoid possible issues with ROM boot loader memory allocation.
Update test_noinit.c file to address RTCWDT_RTC_RESET reset reason instead of POWERON_RESET.
Test optimized to pass automated unit testing.
esp32: Add .noinit and .rtc_noinit sections to the linker script
Update of general-notes.rst documentation to fomat examples as code and attributes as identifiers.
Test test_noinit.c corrected to pass automated testing (support ofTEST_CASE_MULTIPLE_STAGES())
https://ezredmine.espressif.cn:8765/issues/15878
2018-05-16 17:33:37 +05:00
2537 changed files with 203847 additions and 177700 deletions
@@ -25,6 +25,8 @@ Before sending us a Pull Request, please consider this list of points:
* Are comments and documentation written in clear English, with no spelling or grammar errors?
* Example contributions are also welcome. Please check the :doc:`creating-examples` guide for these.
* If the contribution contains multiple commits, are they grouped together into logical changes (one major change per pull request)? Are any commits with names like "fixed typo" `squashed into previous commits <http://eli.thegreenplace.net/2014/02/19/squashing-github-pull-requests-into-a-single-commit/>`_?
* If you're unsure about any of these points, please open the Pull Request anyhow and then ask us for feedback.
* [Getting Started Guide for the stable ESP-IDF version](https://docs.espressif.com/projects/esp-idf/en/stable/get-started/)
* [Getting Started Guide for the latest (master branch) ESP-IDF version](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/)
## Finding a Project
As well as the [esp-idf-template](https://github.com/espressif/esp-idf-template) project mentioned in the setup guide, ESP-IDF comes with some example projects in the [examples](examples) directory.
As well as the [esp-idf-template](https://github.com/espressif/esp-idf-template) project mentioned in Getting Started, ESP-IDF comes with some example projects in the [examples](examples) directory.
Once you've found the project you want to work with, change to its directory and you can configure and build it.
To start your own project based on an example, copy the example project directory outside of the ESP-IDF directory.
# Quick Reference
See the Getting Started guide links above for a detailed setup guide. This is a quick reference for common commands when working with ESP-IDF projects:
## Configuring the Project
`idf.py menuconfig`
`make menuconfig`
* Opens a text-based configuration menu for the project.
* Use up & down arrow keys to navigate the menu.
@@ -36,41 +41,54 @@ Once done configuring, press Escape multiple times to exit and say "Yes" to save
## Compiling the Project
`idf.py build`
`make -j4 all`
... will compile app, bootloader and generate a partition table based on the config.
NOTE: The `-j4` option causes `make` to run 4 parallel jobs. This is much faster than the default single job. The recommended number to pass to this option is `-j(number of CPUs + 1)`.
## Flashing the Project
When the build finishes, it will print a command line to use esptool.py to flash the chip. However you can also do this automatically by running:
`idf.py flash`
`make -j4 flash`
This will flash the entire project (app, bootloader and partition table) to a new chip. The settings for serial port flashing can be configured with `idf.py menuconfig`.
This will flash the entire project (app, bootloader and partition table) to a new chip. The settings for serial port flashing can be configured with `make menuconfig`.
You don't need to run `idf.py build` before running `idf.py flash`, `idf.py flash` will automatically rebuild anything which needs it.
You don't need to run `make all` before running `make flash`, `make flash` will automatically rebuild anything which needs it.
## Viewing Serial Output
The `idf.py monitor` target uses the [idf_monitor tool](https://esp-idf.readthedocs.io/en/latest/get-started/idf-monitor.html) to display serial output from the ESP32. idf_monitor also has a range of features to decode crash output and interact with the device. [Check the documentation page for details](https://esp-idf.readthedocs.io/en/latest/get-started/idf-monitor.html).
The `make monitor` target uses the [idf_monitor tool](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/idf-monitor.html) to display serial output from the ESP32. idf_monitor also has a range of features to decode crash output and interact with the device. [Check the documentation page for details](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/idf-monitor.html).
Exit the monitor by typing Ctrl-].
To flash and monitor output in one pass, you can run:
To build, flash and monitor output in one pass, you can run:
`idf.py flash monitor`
`make -j4 flash monitor`
## Compiling & Flashing Just the App
## Compiling & Flashing Only the App
After the initial flash, you may just want to build and flash just your app, not the bootloader and partition table:
*`idf.py app` - build just the app.
*`idf.py app-flash` - flash just the app.
*`make app` - build just the app.
*`make app-flash` - flash just the app.
`idf.py app-flash` will automatically rebuild the app if it needs it.
`make app-flash` will automatically rebuild the app if any source files have changed.
(In normal development there's no downside to reflashing the bootloader and partition table each time, if they haven't changed.)
## Parallel Builds
ESP-IDF supports compiling multiple files in parallel, so all of the above commands can be run as `make -jN` where `N` is the number of parallel make processes to run (generally N should be equal to the number of CPU cores in your system, plus one.)
Multiple make functions can be combined into one. For example: to build the app & bootloader using 5 jobs in parallel, then flash everything, and then display serial output from the ESP32 run:
```
make -j5 flash monitor
```
## The Partition Table
Once you've compiled your project, the "build" directory will contain a binary file with a name like "my_app.bin". This is an ESP32 image binary that can be loaded by the bootloader.
@@ -79,29 +97,29 @@ A single ESP32's flash can contain multiple apps, as well as many different kind
Each entry in the partition table has a name (label), type (app, data, or something else), subtype and the offset in flash where the partition is loaded.
The simplest way to use the partition table is to `idf.py menuconfig` and choose one of the simple predefined partition tables:
The simplest way to use the partition table is to `make menuconfig` and choose one of the simple predefined partition tables:
* "Single factory app, no OTA"
* "Factory app, two OTA definitions"
In both cases the factory app is flashed at offset 0x10000. If you `idf.py partition_table` then it will print a summary of the partition table.
In both cases the factory app is flashed at offset 0x10000. If you `make partition_table` then it will print a summary of the partition table.
For more details about partition tables and how to create custom variations, view the [`docs/en/api-guides/partition-tables.rst`](docs/en/api-guides/partition-tables.rst) file.
## Erasing Flash
The `idf.py flash` target does not erase the entire flash contents. However it is sometimes useful to set the device back to a totally erased state, particularly when making partition table changes or OTA app updates. To erase the entire flash, run `idf.py erase_flash`.
The `make flash` target does not erase the entire flash contents. However it is sometimes useful to set the device back to a totally erased state, particularly when making partition table changes or OTA app updates. To erase the entire flash, run `make erase_flash`.
This can be combined with other targets, ie `idf.py erase_flash flash` will erase everything and then re-flash the new app, bootloader and partition table.
This can be combined with other targets, ie `make erase_flash flash` will erase everything and then re-flash the new app, bootloader and partition table.
# Resources
* Documentation for the latest version: https://esp-idf.readthedocs.io/. This documentation is built from the [docs directory](docs) of this repository.
* Documentation for the latest version: https://docs.espressif.com/projects/esp-idf/. This documentation is built from the [docs directory](docs) of this repository.
* The [esp32.com forum](https://esp32.com/) is a place to ask questions and find community resources.
* [Check the Issues section on github](https://github.com/espressif/esp-idf/issues) if you find a bug or have a feature request. Please check existing Issues before opening a new one.
* If you're interested in contributing to ESP-IDF, please check the [Contributions Guide](https://esp-idf.readthedocs.io/en/latest/contribute/index.html).
* If you're interested in contributing to ESP-IDF, please check the [Contributions Guide](https://docs.espressif.com/projects/esp-idf/en/latest/contribute/index.html).
#define SEGGER_SYSVIEW_ID_BASE 0x3F400000 // Default value for the lowest Id reported by the application. Can be overridden by the application via SEGGER_SYSVIEW_SetRAMBase(). (i.e. 0x20000000 when all Ids are an address in this RAM)
#define SEGGER_SYSVIEW_ID_SHIFT 0 // Number of bits to shift the Id to save bandwidth. (i.e. 2 when Ids are 4 byte aligned)
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() ((*(U32 *)(0xE000ED04)) & 0x1FF) // Get the currently active interrupt Id. (i.e. read Cortex-M ICSR[8:0] = active vector)
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() (__get_IPSR()) // Workaround for IAR, which might do a byte-access to 0xE000ED04. Read IPSR instead.
#else
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() ((*(U32 *)(0xE000ED04)) & 0x3F) // Get the currently active interrupt Id. (i.e. read Cortex-M ICSR[5:0] = active vector)
#endif
#else
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() SEGGER_SYSVIEW_X_GetInterruptId() // Get the currently active interrupt Id from the user-provided function.
#define SEGGER_SYSVIEW_ID_BASE 0x3F400000 // Default value for the lowest Id reported by the application. Can be overridden by the application via SEGGER_SYSVIEW_SetRAMBase(). (i.e. 0x20000000 when all Ids are an address in this RAM)
#define SEGGER_SYSVIEW_ID_SHIFT 0 // Number of bits to shift the Id to save bandwidth. (i.e. 2 when Ids are 4 byte aligned)
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() ((*(U32 *)(0xE000ED04)) & 0x1FF) // Get the currently active interrupt Id. (i.e. read Cortex-M ICSR[8:0] = active vector)
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() (__get_IPSR()) // Workaround for IAR, which might do a byte-access to 0xE000ED04. Read IPSR instead.
#else
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() ((*(U32 *)(0xE000ED04)) & 0x3F) // Get the currently active interrupt Id. (i.e. read Cortex-M ICSR[5:0] = active vector)
#endif
#else
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() SEGGER_SYSVIEW_X_GetInterruptId() // Get the currently active interrupt Id from the user-provided function.
#define SEGGER_SYSVIEW_INFO_SIZE 9 // Minimum size, which has to be reserved for a packet. 1-2 byte of message type, 0-2 byte of payload length, 1-5 bytes of timestamp.
#define SEGGER_SYSVIEW_QUANTA_U32 5 // Maximum number of bytes to encode a U32, should be reserved for each 32-bit value in a packet.
#define SEGGER_SYSVIEW_LOG (0u)
#define SEGGER_SYSVIEW_WARNING (1u)
#define SEGGER_SYSVIEW_ERROR (2u)
#define SEGGER_SYSVIEW_FLAG_APPEND (1u << 6)
#define SEGGER_SYSVIEW_PREPARE_PACKET(p) (p) + 4
//
// SystemView events. First 32 IDs from 0 .. 31 are reserved for these
#define SEGGER_SYSVIEW_INFO_SIZE 9 // Minimum size, which has to be reserved for a packet. 1-2 byte of message type, 0-2 byte of payload length, 1-5 bytes of timestamp.
#define SEGGER_SYSVIEW_QUANTA_U32 5 // Maximum number of bytes to encode a U32, should be reserved for each 32-bit value in a packet.
#define SEGGER_SYSVIEW_LOG (0u)
#define SEGGER_SYSVIEW_WARNING (1u)
#define SEGGER_SYSVIEW_ERROR (2u)
#define SEGGER_SYSVIEW_FLAG_APPEND (1u << 6)
#define SEGGER_SYSVIEW_PREPARE_PACKET(p) (p) + 4
//
// SystemView events. First 32 IDs from 0 .. 31 are reserved for these
* If the OTA data partition is not present or not valid then the result is the first app partition found in the
* partition table. In priority order, this means: the factory app, the first OTA app slot, or the test app partition.
*
* Note that there is no guarantee the returned partition is a valid app. Use esp_image_load(ESP_IMAGE_VERIFY, ...) to verify if the
* Note that there is no guarantee the returned partition is a valid app. Use esp_image_verify(ESP_IMAGE_VERIFY, ...) to verify if the
* returned partition contains a bootable image.
*
* @return Pointer to info for partition structure, or NULL if partition table is invalid or a flash read operation failed. Any returned pointer is valid for the lifetime of the application.
The GPIO must be held low continuously for this period of time after reset
before a factory reset or test partition boot (as applicable) is performed.
config BOOTLOADER_WDT_ENABLE
bool "Use RTC watchdog in start code"
default y
help
Tracks the execution time of startup code.
If the execution time is exceeded, the RTC_WDT will restart system.
It is also useful to prevent a lock up in start code caused by an unstable power source.
NOTE: Tracks the execution time starts from the bootloader code - re-set timeout, while selecting the source for slow_clk - and ends calling app_main.
Re-set timeout is needed due to WDT uses a SLOW_CLK clock source. After changing a frequency slow_clk a time of WDT needs to re-set for new frequency.
slow_clk depends on ESP32_RTC_CLOCK_SOURCE (INTERNAL_RC or EXTERNAL_CRYSTAL).
config BOOTLOADER_WDT_DISABLE_IN_USER_CODE
bool "Allows RTC watchdog disable in user code"
depends on BOOTLOADER_WDT_ENABLE
default n
help
If it is set, the client must itself reset or disable rtc_wdt in their code (app_main()).
Otherwise rtc_wdt will be disabled before calling app_main function.
Use function rtc_wdt_feed() for resetting counter of rtc_wdt.
Use function rtc_wdt_disable() for disabling rtc_wdt.
config BOOTLOADER_WDT_TIME_MS
int "Timeout for RTC watchdog (ms)"
depends on BOOTLOADER_WDT_ENABLE
default 9000
range 0 120000
help
Verify that this parameter is correct and more then the execution time.
Pay attention to options such as reset to factory, trigger test partition and encryption on boot
- these options can increase the execution time.
Note: RTC_WDT will reset while encryption operations will be performed.
endmenu # Bootloader
menu "Security features"
# These three are the actual options to check in code,
# selected by the displayed options
config SECURE_SIGNED_ON_BOOT
bool
default y
depends on SECURE_BOOT_ENABLED || SECURE_SIGNED_ON_BOOT_NO_SECURE_BOOT
config SECURE_SIGNED_ON_UPDATE
bool
default y
depends on SECURE_BOOT_ENABLED || SECURE_SIGNED_ON_UPDATE_NO_SECURE_BOOT
config SECURE_SIGNED_APPS
bool
default y
depends on SECURE_SIGNED_ON_BOOT || SECURE_SIGNED_ON_UPDATE
config SECURE_SIGNED_APPS_NO_SECURE_BOOT
bool "Require signed app images"
default n
depends on !SECURE_BOOT_ENABLED
help
Require apps to be signed to verify their integrity.
This option uses the same app signature scheme as hardware secure boot, but unlike hardware secure boot it does not prevent the bootloader from being physically updated. This means that the device can be secured against remote network access, but not physical access. Compared to using hardware Secure Boot this option is much simpler to implement.
config SECURE_SIGNED_ON_BOOT_NO_SECURE_BOOT
bool "Bootloader verifies app signatures"
default n
depends on SECURE_SIGNED_APPS_NO_SECURE_BOOT
help
If this option is set, the bootloader will be compiled with code to verify that an app is signed before booting it.
If hardware secure boot is enabled, this option is always enabled and cannot be disabled.
If hardware secure boot is not enabled, this option doesn't add significant security by itself so most users will want to leave it disabled.
config SECURE_SIGNED_ON_UPDATE_NO_SECURE_BOOT
bool "Verify app signature on update"
default y
depends on SECURE_SIGNED_APPS_NO_SECURE_BOOT
help
If this option is set, any OTA updated apps will have the signature verified before being considered valid.
When enabled, the signature is automatically checked whenever the esp_ota_ops.h APIs are used for OTA updates,
or esp_image_format.h APIs are used to verify apps.
If hardware secure boot is enabled, this option is always enabled and cannot be disabled.
If hardware secure boot is not enabled, this option still adds significant security against network-based attackers by preventing spoofing of OTA updates.
config SECURE_BOOT_ENABLED
bool "Enable secure boot in bootloader (READ DOCS FIRST)"
default N
bool "Enable hardware secure boot in bootloader (READ DOCS FIRST)"
default n
help
Build a bootloader which enables secure boot on first boot.
@@ -142,7 +224,7 @@ config SECURE_BOOT_ENABLED
When enabling secure boot, JTAG and ROM BASIC Interpreter are permanently disabled by default.
Refer to https://esp-idf.readthedocs.io/en/latest/security/secure-boot.html before enabling.
Refer to https://docs.espressif.com/projects/esp-idf/en/latest/security/secure-boot.html before enabling.
choice SECURE_BOOTLOADER_MODE
bool "Secure bootloader mode"
@@ -169,12 +251,12 @@ endchoice
config SECURE_BOOT_BUILD_SIGNED_BINARIES
bool "Sign binaries during build"
depends on SECURE_BOOT_ENABLED
depends on SECURE_SIGNED_APPS
default y
help
Once secure boot is enabled, bootloader will only boot if partition table and app image are signed.
Once secure boot or signed app requirement is enabled, app images are required to be signed.
If enabled, these binary files are signed as part of the build process. The file named in "Secure boot private signing key" will be used to sign the image.
If enabled (default), these binary files are signed as part of the build process. The file named in "Secure boot private signing key" will be used to sign the image.
If disabled, unsigned app/partition data will be built. They must be signed manually using espsecure.py (for example, on a remote signing server.)
Path to the key file used to sign partition tables and app images for secure boot. Once secure boot is enabled, bootloader will only boot if partition table and app image are signed.
Path to the key file used to sign app images.
Key file is an ECDSA private key (NIST256p curve) in PEM format.
bool "Allow app partition length not 64KB aligned"
depends on SECURE_BOOT_INSECURE
help
If not set (default), app partition size must be a multiple of 64KB. App images are padded to 64KB length, and the bootloader checks any trailing bytes after the signature (before the next 64KB boundary) have not been written. This is because flash cache maps entire 64KB pages into the address space. This prevents an attacker from appending unverified data after the app image in the flash, causing it to be mapped into the address space.
Setting this option allows the app partition length to be unaligned, and disables padding of the app image to this length. It is generally not recommended to set this option, unless you have a legacy partitioning scheme which doesn't support 64KB aligned partition lengths.
@@ -8,12 +8,19 @@ Linker file used to link the bootloader.
The main purpose is to make sure the bootloader can load into main memory
without overwriting itself.
*/
MEMORY
{
/* I/O */
dport0_seg (RW) : org = 0x3FF00000, len = 0x10
/* IRAM POOL1, used for APP CPU cache. We can abuse it in bootloader because APP CPU is still held in reset, the main app enables APP CPU cache */
iram_seg (RWX) : org = 0x40078000, len = 0x8000
/* IRAM POOL1, used for APP CPU cache. Bootloader runs from here during the final stage of loading the app because APP CPU is still held in reset, the main app enables APP CPU cache */
iram_loader_seg (RWX) : org = 0x40078000, len = 0x8000 /* 32KB, APP CPU cache */
/* 63kB, IRAM. We skip the first 1k to prevent the entry point being
placed into the same range as exception vectors in the app.
This leads to idf_monitor decoding ROM bootloader "entry 0x40080xxx"
message as one of the exception vectors, which looks scary to users.
*/
iram_seg (RWX) : org = 0x40080400, len = 0xfc00
/* 64k at the end of DRAM, after ROM bootloader stack */
/* @brief Encode one or more sets of 6 byte sequences into
* 8 bytes suitable for 3/4 Coding Scheme.
*
* This function is only useful if the CODING_SCHEME efuse
* is set to value 1 for 3/4 Coding Scheme.
*
* @param[in] in_bytes Pointer to a sequence of bytes to encode for 3/4 Coding Scheme. Must have length in_bytes_len. After being written to hardware, these bytes will read back as little-endian words.
* @param[out] out_words Pointer to array of words suitable for writing to efuse write registers. Array must contain 2 words (8 bytes) for every 6 bytes in in_bytes_len. Can be a pointer to efuse write registers.
* @param in_bytes_len. Length of array pointed to by in_bytes, in bytes. Must be a multiple of 6.
*
* @return ESP_ERR_INVALID_ARG if either pointer is null or in_bytes_len is not a multiple of 6. ESP_OK otherwise.
Enable/disable bluetooth controller low power mode.
Note that currently there is problem in the combination use of bluetooth modem sleep and Dynamic Frequency Scaling(DFS). So do not enable DFS if bluetooth modem sleep is in use.
choice BTDM_MODEM_SLEEP_MODE
prompt "Bluetooth Modem sleep mode"
@@ -84,11 +145,13 @@ choice BTDM_MODEM_SLEEP_MODE
config BTDM_MODEM_SLEEP_MODE_ORIG
bool "ORIG Mode(sleep with low power clock)"
help
ORIG mode is a deep sleep mode that can be used for dual mode controller. In this mode, bluetooth controller sleeps between BR/EDR frames and BLE events. A low power clock is used to maintain bluetooth reference clock.
ORIG mode is a bluetooth sleep mode that can be used for dual mode controller. In this mode, bluetooth controller
sleeps between BR/EDR frames and BLE events. A low power clock is used to maintain bluetooth reference clock.
config BTDM_MODEM_SLEEP_MODE_EVED
bool "EVED Mode"
bool "EVED Mode(For internal test only)"
help
This mode is for BLE only.
EVED mode is for BLE only and is only for internal test. Do not use it for production. this mode is not compatible
with DFS nor light sleep
endchoice
choice BTDM_LOW_POWER_CLOCK
@@ -99,11 +162,122 @@ choice BTDM_LOW_POWER_CLOCK
config BTDM_LPCLK_SEL_MAIN_XTAL
bool "Main crystal"
help
Main crystal can be used as low power clock for bluetooth modem sleep. If this option is selected, bluetooth
modem sleep can work under Dynamic Frequency Scaling(DFS) enabled, but cannot work when light sleep is enabled.
Main crystal has a relatively better performance than other bluetooth low power clock sources.
config BTDM_LPCLK_SEL_EXT_32K_XTAL
bool "External 32kHz crystal"
depends on ESP32_RTC_CLOCK_SOURCE_EXTERNAL_CRYSTAL
endchoice
endmenu
config BLE_SCAN_DUPLICATE
bool "BLE Scan Duplicate Options"
depends on (BTDM_CONTROLLER_MODE_BTDM || BTDM_CONTROLLER_MODE_BLE_ONLY)
default y
help
This select enables parameters setting of BLE scan duplicate.
choice SCAN_DUPLICATE_TYPE
prompt "Scan Duplicate Type"
default SCAN_DUPLICATE_BY_DEVICE_ADDR
depends on BLE_SCAN_DUPLICATE
help
Scan duplicate have three ways. one is "Scan Duplicate By Device Address", This way is to use advertiser address
filtering. The adv packet of the same address is only allowed to be reported once. Another way is "Scan Duplicate
By Device Address And Advertising Data". This way is to use advertising data and device address filtering. All
different adv packets with the same address are allowed to be reported. The last way is "Scan Duplicate By Advertising
Data". This way is to use advertising data filtering. All same advertising data only allow to be reported once even though
they are from different devices.
config SCAN_DUPLICATE_BY_DEVICE_ADDR
bool "Scan Duplicate By Device Address"
help
This way is to use advertiser address filtering. The adv packet of the same address is only allowed to be reported once
config SCAN_DUPLICATE_BY_ADV_DATA
bool "Scan Duplicate By Advertising Data"
help
This way is to use advertising data filtering. All same advertising data only allow to be reported once even though
they are from different devices.
config SCAN_DUPLICATE_BY_ADV_DATA_AND_DEVICE_ADDR
bool "Scan Duplicate By Device Address And Advertising Data"
help
This way is to use advertising data and device address filtering. All different adv packets with the same address are
allowed to be reported.
endchoice
config SCAN_DUPLICATE_TYPE
int
depends on BLE_SCAN_DUPLICATE
default 0 if SCAN_DUPLICATE_BY_DEVICE_ADDR
default 1 if SCAN_DUPLICATE_BY_ADV_DATA
default 2 if SCAN_DUPLICATE_BY_ADV_DATA_AND_DEVICE_ADDR
default 0
config DUPLICATE_SCAN_CACHE_SIZE
int "Maximum number of devices in scan duplicate filter"
depends on BLE_SCAN_DUPLICATE
range 10 1000
default 200
help
Maximum number of devices which can be recorded in scan duplicate filter.
When the maximum amount of device in the filter is reached, the cache will be refreshed.
config BLE_MESH_SCAN_DUPLICATE_EN
bool "Special duplicate scan mechanism for BLE Mesh scan"
depends on BLE_SCAN_DUPLICATE
default n
help
This enables the BLE scan duplicate for special BLE Mesh scan.
config MESH_DUPLICATE_SCAN_CACHE_SIZE
int "Maximum number of Mesh adv packets in scan duplicate filter"
depends on BLE_MESH_SCAN_DUPLICATE_EN
range 10 1000
default 200
help
Maximum number of adv packets which can be recorded in duplicate scan cache for BLE Mesh.
When the maximum amount of device in the filter is reached, the cache will be refreshed.
config BLE_ADV_REPORT_FLOW_CONTROL_SUPPORTED
bool "BLE adv report flow control supported"
depends on (BTDM_CONTROLLER_MODE_BTDM || BTDM_CONTROLLER_MODE_BLE_ONLY)
default y
help
The function is mainly used to enable flow control for advertising reports. When it is enabled,
advertising reports will be discarded by the controller if the number of unprocessed advertising
reports exceeds the size of BLE adv report flow control.
config BLE_ADV_REPORT_FLOW_CONTROL_NUM
int "BLE adv report flow control number"
depends on BLE_ADV_REPORT_FLOW_CONTROL_SUPPORTED
range 50 1000
default 100
help
The number of unprocessed advertising report that Bluedroid can save.If you set
`BLE_ADV_REPORT_FLOW_CONTROL_NUM` to a small value, this may cause adv packets lost.
If you set `BLE_ADV_REPORT_FLOW_CONTROL_NUM` to a large value, Bluedroid may cache a
lot of adv packets and this may cause system memory run out. For example, if you set
it to 50, the maximum memory consumed by host is 35 * 50 bytes. Please set
`BLE_ADV_REPORT_FLOW_CONTROL_NUM` according to your system free memory and handle adv
packets as fast as possible, otherwise it will cause adv packets lost.
config BLE_ADV_REPORT_DISCARD_THRSHOLD
int "BLE adv lost event threshold value"
depends on BLE_ADV_REPORT_FLOW_CONTROL_SUPPORTED
range 1 1000
default 20
help
When adv report flow control is enabled, The ADV lost event will be generated when the number
of ADV packets lost in the controller reaches this threshold. It is better to set a larger value.
If you set `BLE_ADV_REPORT_DISCARD_THRSHOLD` to a small value or printf every adv lost event, it
may cause adv packets lost more.
endmenu
menuconfig BLUEDROID_ENABLED
@@ -208,25 +382,65 @@ endchoice
config GATTS_ENABLE
bool "Include GATT server module(GATTS)"
depends on BLUEDROID_ENABLED
depends on BLUEDROID_ENABLED && (BTDM_CONTROLLER_MODE_BTDM || BTDM_CONTROLLER_MODE_BLE_ONLY)
default y
help
This option can be disabled when the app work only on gatt client mode
choice GATTS_SEND_SERVICE_CHANGE_MODE
prompt "GATTS Service Change Mode"
default GATTS_SEND_SERVICE_CHANGE_AUTO
depends on GATTS_ENABLE
help
Service change indication mode for GATT Server.
config GATTS_SEND_SERVICE_CHANGE_MANUAL
bool "GATTS manually send service change indication"
help
Manually send service change indication through API esp_ble_gatts_send_service_change_indication()
config GATTS_SEND_SERVICE_CHANGE_AUTO
bool "GATTS automatically send service change indication"
help
Let Bluedroid handle the service change indication internally
endchoice
config GATTS_SEND_SERVICE_CHANGE_MODE
int
depends on GATTS_ENABLE
default 0 if GATTS_SEND_SERVICE_CHANGE_AUTO
default 1 if GATTS_SEND_SERVICE_CHANGE_MANUAL
default 0
config GATTC_ENABLE
bool "Include GATT client module(GATTC)"
depends on BLUEDROID_ENABLED
depends on BLUEDROID_ENABLED && (BTDM_CONTROLLER_MODE_BTDM || BTDM_CONTROLLER_MODE_BLE_ONLY)
default y
help
This option can be close when the app work only on gatt server mode
config GATTC_CACHE_NVS_FLASH
bool "Save gattc cache data to nvs flash"
depends on GATTC_ENABLE && (BTDM_CONTROLLER_MODE_BTDM || BTDM_CONTROLLER_MODE_BLE_ONLY)
default n
help
This select can save gattc cache data to nvs flash
config BLE_SMP_ENABLE
bool "Include BLE security module(SMP)"
depends on BLUEDROID_ENABLED
depends on BLUEDROID_ENABLED && (BTDM_CONTROLLER_MODE_BTDM || BTDM_CONTROLLER_MODE_BLE_ONLY)
default y
help
This option can be close when the app not used the ble security connect.
config SMP_SLAVE_CON_PARAMS_UPD_ENABLE
bool "Slave enable connection parameters update during pairing"
depends on BLE_SMP_ENABLE
default n
help
In order to reduce the pairing time, slave actively initiates connection parameters update during pairing.
ESP_GAP_SEARCH_INQ_DISCARD_NUM_EVT=7,/*!< The number of pkt discarded by flow control */
}esp_gap_search_evt_t;
/**
@@ -549,6 +572,34 @@ typedef enum{
ESP_BLE_WHITELIST_REMOVE=0X00,/*!< remove mac from whitelist */
ESP_BLE_WHITELIST_ADD=0X01,/*!< add address to whitelist */
}esp_ble_wl_opration_t;
typedefenum{
ESP_BLE_DUPLICATE_EXCEPTIONAL_LIST_ADD=0,/*!< Add device info into duplicate scan exceptional list */
ESP_BLE_DUPLICATE_EXCEPTIONAL_LIST_REMOVE,/*!< Remove device info from duplicate scan exceptional list */
ESP_BLE_DUPLICATE_EXCEPTIONAL_LIST_CLEAN,/*!< Clean duplicate scan exceptional list */
}esp_bt_duplicate_exceptional_subcode_type_t;
#define BLE_BIT(n) (1UL<<(n))
typedefenum{
ESP_BLE_DUPLICATE_SCAN_EXCEPTIONAL_INFO_ADV_ADDR=0,/*!< BLE advertising address , device info will be added into ESP_BLE_DUPLICATE_SCAN_EXCEPTIONAL_ADDR_LIST */
ESP_BLE_DUPLICATE_SCAN_EXCEPTIONAL_INFO_MESH_LINK_ID,/*!< BLE mesh link ID, it is for BLE mesh, device info will be added into ESP_BLE_DUPLICATE_SCAN_EXCEPTIONAL_MESH_LINK_ID_LIST */
ESP_BLE_DUPLICATE_SCAN_EXCEPTIONAL_INFO_MESH_BEACON_TYPE,/*!< BLE mesh beacon AD type, the format is | Len | 0x2B | Beacon Type | Beacon Data | */
ESP_BLE_DUPLICATE_SCAN_EXCEPTIONAL_INFO_MESH_PROV_SRV_ADV,/*!< BLE mesh provisioning service uuid, the format is | 0x02 | 0x01 | flags | 0x03 | 0x03 | 0x1827 | .... |` */
ESP_BLE_DUPLICATE_SCAN_EXCEPTIONAL_INFO_MESH_PROXY_SRV_ADV,/*!< BLE mesh adv with proxy service uuid, the format is | 0x02 | 0x01 | flags | 0x03 | 0x03 | 0x1828 | .... |` */
}esp_ble_duplicate_exceptional_info_type_t;
typedefenum{
ESP_BLE_DUPLICATE_SCAN_EXCEPTIONAL_ADDR_LIST=BLE_BIT(0),/*!< duplicate scan exceptional addr list */
ESP_BLE_DUPLICATE_SCAN_EXCEPTIONAL_MESH_LINK_ID_LIST=BLE_BIT(1),/*!< duplicate scan exceptional mesh link ID list */
ESP_BLE_DUPLICATE_SCAN_EXCEPTIONAL_MESH_BEACON_TYPE_LIST=BLE_BIT(2),/*!< duplicate scan exceptional mesh beacon type list */
ESP_BLE_DUPLICATE_SCAN_EXCEPTIONAL_MESH_PROV_SRV_ADV_LIST=BLE_BIT(3),/*!< duplicate scan exceptional mesh adv with provisioning service uuid */
ESP_BLE_DUPLICATE_SCAN_EXCEPTIONAL_MESH_PROXY_SRV_ADV_LIST=BLE_BIT(4),/*!< duplicate scan exceptional mesh adv with provisioning service uuid */
ESP_BLE_DUPLICATE_SCAN_EXCEPTIONAL_ALL_LIST=0xFFFF,/*!< duplicate scan exceptional all list */
esp_bt_status_tstatus;/*!< Indicate the add or remove whitelist operation success status */
esp_ble_wl_opration_twl_opration;/*!< The value is ESP_BLE_WHITELIST_ADD if add address to whitelist operation success, ESP_BLE_WHITELIST_REMOVE if remove address from the whitelist operation success */
}update_whitelist_cmpl;/*!< Event parameter of ESP_GAP_BLE_UPDATE_WHITELIST_COMPLETE_EVT */
ESP_GATT_CONN_L2C_FAILURE=1,/*!< General L2cap failure *//* relate to BTA_GATT_CONN_L2C_FAILURE in bta/bta_gatt_api.h */
ESP_GATT_CONN_TIMEOUT=0x08,/*!< Connection timeout *//* relate to BTA_GATT_CONN_TIMEOUT in bta/bta_gatt_api.h */
ESP_GATT_CONN_TERMINATE_PEER_USER=0x13,/*!< Connection terminate by peer user *//* relate to BTA_GATT_CONN_TERMINATE_PEER_USER in bta/bta_gatt_api.h */
ESP_GATT_CONN_TERMINATE_LOCAL_HOST=0x16,/*!< Connectionterminated by local host *//* relate to BTA_GATT_CONN_TERMINATE_LOCAL_HOST in bta/bta_gatt_api.h */
ESP_GATT_CONN_TERMINATE_LOCAL_HOST=0x16,/*!< Connectionterminated by local host *//* relate to BTA_GATT_CONN_TERMINATE_LOCAL_HOST in bta/bta_gatt_api.h */
ESP_GATT_CONN_FAIL_ESTABLISH=0x3e,/*!< Connection fail to establish *//* relate to BTA_GATT_CONN_FAIL_ESTABLISH in bta/bta_gatt_api.h */
ESP_GATT_CONN_LMP_TIMEOUT=0x22,/*!< Connection fail for LMP response tout *//* relate to BTA_GATT_CONN_LMP_TIMEOUT in bta/bta_gatt_api.h */
ESP_GATT_CONN_CONN_CANCEL=0x0100,/*!< L2CAP connection cancelled *//* relate to BTA_GATT_CONN_CONN_CANCEL in bta/bta_gatt_api.h */
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
