Add IPv6 support for multus validation tool. Also test that IPv6 support
works by specifying one of the NetAttachDefs with an IPv6 address range.
Signed-off-by: Blaine Gardner <blaine.gardner@ibm.com>
When the clusters reach full, nearfull, or backfill full thresholds
ceph will raise health warnings and stop allowing IO or backfill
depending on the threshold. These settings require special ceph
commands instead of being generic ceph config. Allow these settings
to be set from the CephCluster CR in the spec.storage
section.
Signed-off-by: Travis Nielsen <tnielsen@redhat.com>
Currently we allow upgrade of other OSDs while migration
of OSD, due to change in backing store, is pending. This
will not work if the updated OSD ceph version does not support
the currently applied backing store. So rook will skip any
OSD upgrade if the OSD migration is pending.
Signed-off-by: sp98 <sapillai@redhat.com>
This PR adds a `settings` option in the `Module` struct
which can help users to futher customize the `balancer`
module with a differet mode.
Signed-off-by: sp98 <sapillai@redhat.com>
When IPv6-only network mode is enabled and when mons are configured to
listen only on msgrV2 port, Rook has to add the port to the mon
--public-bind-addr in order to force mons to stop listening on the
msgrV1 port. This can cause problems for IPv6 clusters where adding
':<port>' to the end of an IP addr looks like a valid IPv6 address.
In IPv6 mode, Rook needs to set this to '[<ip>]:<port>' with the
brackets to be a non-ambiguous IPv6 address.
In IPv4 mode, Rook needs to keep its existing behavior. IPv4 mode should
also continue to be the defualt assumption if the network config isn't
specified.
If 'dualStack: true' is specified, Rook is informed that the environment
is dual stack, but Rook doesn't know which IP family to expect from the
pod IP. In this scenario, it is safest for Rook not to apply the port,
since assuming either IPv4 or IPv6 format could be incorrect. In this
scenario, mons may still listen on msgrV1 ports, but this is preferable
to an environment where mons perpetually crash.
Signed-off-by: Blaine Gardner <blaine.gardner@ibm.com>
currently node predicate watches for resourceVersion and heartbeat
changes, which are not critical things. So with the PR we will add
a early-exit condition for the predicate as an optimization and to
ignore considering for a reconcile of cephcluster if updates are
not crucial
closes: https://github.com/rook/rook/issues/14070
Signed-off-by: parth-gr <partharora1010@gmail.com>
Ceph-CSI support for fscrypt encryption of cephfs.
To achieve this commit add capability of mounting the
required `rook-ceph-csi-kms-config` configmap into
csi-cephfsplugin-provisioner and nodeplugin pods.
Further it modifies the ClusterRoles `cephfs-csi-nodeplugin` and
`cephfs-external-provisioner-runner` to grant privileges
required for reading encryption configuration and fetching
encryption secrets from either kubernetes secrets or
from a Key Management System (KMS).
These privileges are essential for the proper functioning of
ceph-csi-cephfs with fscrypt encryption.
The following privileges have been added:
- `secrets/get`: Allows reading of secrets for encryption.
- `configmaps/get`: Grants access to configuration maps,
this is used to read encryption configuration.
- `serviceaccounts/get`: Enables retrieval of service accounts for
authentication to KMS and for retrieving encryption secrets
stored there.
- `serviceaccounts/token/create`: Allows creation of service account tokens,
which are required for authenticating requests to KMS
when retrieving encryption secrets.
The commit also updated the csi documentation to include cephfs
in the encryption section, with examples updated accordingly.
Signed-off-by: NymanRobin <robin.nyman@est.tech>
SVG cleanup job uses the cephSubvolumeGroup env name
from spec.Name. But sometimes it can be empty. In that
case rook should use the CR name.
Signed-off-by: sp98 <sapillai@redhat.com>
LVM-based OSDs on PVCs are legacy and are not well tested.
Therefore, we add status to the cephcluster CR that at least
gives a clue that the OSDs should be replaced.
Signed-off-by: Travis Nielsen <tnielsen@redhat.com>
fix UpdateActiveMgrLabel to retry label update on failure. Previously,
the function always returned the current manager, even if update
failed, leading to inconsistent labels. This fix ensures retries on
failures.
Fixes: https://github.com/rook/rook/issues/13601
Signed-off-by: Redouane Kachach <rkachach@ibm.com>
there are some cases where storageClassDeviceSets length
are more 63 chars and osd provisioned failed due to this.
with error
```
failed to run osd provisioning job for PVC "ocs-deviceset-*-local-volume-storageclass-0-data-*": Job.batch "rook-ceph-osd-prepare-*" is invalid: [spec.template.spec.volumes[10].name: Invalid value: "ocs-deviceset-*-local-volume-storageclass-0-data-*": must be no more than 63 characters, spec.template.spec.containers[0].volumeMounts[9].name: Not found: "ocs-deviceset-*-local-volume-storageclass-0-data-*",
```
Using x-validator to limit the maxLength to the deviceClassSet.Name to
40 chars and adding code check that overall pvc name should be less than
63 chars.
Signed-off-by: subhamkrai <srai@redhat.com>
Someone testing the Multus holder pod removal feature encountered an
issue where the migration process failed to lead to a system state where
PVCs could be created successfully.
The root cause was found to be a ceph csi config map wherein the primary
CephCluster entry was lacking a value for the "namespace" field.
I observed this once in my development on the holder pod removal
feature, but I was unable to reproduce and assumed it was my own error.
Since this has been seen in a user environment, it must be that the
error is a race condition, and I am unable to determine the exact source
of the bug.
I do not believe this bug would be present if the code that updates the
CSI configmap were properly idempotent, but it has many conditions based
on prior states, and I was unable to determine how to resolve this
underlying impelementation pattern issue.
Instead, I opted to separate the `clusterKey` parameter into two clear
parts:
1. `clusterID` for when `clusterKey` is used as an analogue for
`clusterID`
2. `clusterNamespace` for when `clusterKey` is used as an analogue for
`clusterNamespace`
I added unit tests to ensure that SaveClusterConfig() will be able to
detect when the namespace is currently missing, and using the new
`clusterNamespace` field, it should always know what value to use as
input when correcting the bug in already-installed systems.
I also verified that this update works when the function simultaneously
removes netNamespaceFilePath entries, and that those entries are removed
properly.
Finally, manual testing also verifies the change.
Signed-off-by: Blaine Gardner <blaine.gardner@ibm.com>
The mon was listening on both v1 and v2 ports inside the daemon
even though the service endpoint would not redirect any traffic
to the v1 port. When msgr2 is required, disable the mon from
listening on the v1 port for reduced security footprint.
Signed-off-by: Travis Nielsen <tnielsen@redhat.com>
With the removal of Ceph Pacific support, no need to check if Quincy
is avaiable to support encryption on the wire.
Signed-off-by: Travis Nielsen <tnielsen@redhat.com>
in case of portable mons, mon scaledown was skipped
with below code
```
if mon.NodeName == "" {
logger.Debugf("mon %q is not scheduled to a specific host", mon.DaemonName)
continue
}
```
which skips mon removal if mon nodeName is empty
but if mons are scale down in case of portable mons
in that case also we want to remove extra mons to match
the cephCluster configuration.
Signed-off-by: subhamkrai <srai@redhat.com>
Unlike other components, the Ceph dashboard Service object could not be
configured with custom labels and annotations. This can be useful when
integrating Rook into a cluster with custom controllers similarly to how
the RGW service is customized.
Signed-off-by: Steven Fackler <sfackler@gmail.com>
OSDs on LVM-mode PVCs are failing to come up and crashing
in the expand-bluefs init container. To avoid the crash
and allow the OSDs to start, a workaround was found to
simply remove that init container. Now we disable the
OSD resize for this case to avoid others hitting this
during upgrade as well.
Signed-off-by: Travis Nielsen <tnielsen@redhat.com>
In the primary CSI reconcile, ensure the CSI config map
(`rook-ceph-csi-config`) has the correct owner info.
This corrects any pre-existing config maps that might have incorrect
owner info, which has observed to include references to CephClusters.
The config map should only have a single reference, and it should refer
to the operator deployment.
If any existing Rook clusters have a CSI config map which has a
CephCluster as an owner, this change will ensure that the config map is
not deleted when the CephCluster is deleted. This is especially
important for any environments with multiple CephClusters installed.
Signed-off-by: Blaine Gardner <blaine.gardner@ibm.com>
There have been some issues with non-CSI Rook controllers that are
creating the CSI config configmap (`rook-ceph-csi-config`). This causes
problems with the K8s OwnerReference. The primary CSI reconciler
(controller) creates the configmap with the correct owner reference,
which is supposed to be the operator deployment.
Other instances were creating the configmap with owner references set to
the CephCluster. This is a minor bug, but it can result in this
configmap being deleted along with the first CephCluster that initially
created it.
To fix this issue, remove all instances of `CreateCsiConfigMap()` except
the single usage which the CSI reconcile uses to initially create the
configmap. Other controllers that might have attempted to create this
configmap previously will return an error indicating that it is waiting
for the configmap to be created.
Signed-off-by: Blaine Gardner <blaine.gardner@ibm.com>
The CreateOrLoadClusterInfo (and therefore LoadClusterInfo) methods were
not loading the ClusterInfo.OwnerInfo. This should help future CRD
controllers get the full ClusterInfo struct without having missing
information. Current controllers that need ClusterInfo fill the field
themselves.
During testing, I observed one corner case where an upgraded cluster was
missing the `rook-ceph-csi-config` configmap. The cluster had a
CephFilesystemSubVolumeGroup resource created, and the reconcile for
that resource was attempting to create the missing CSI configmap and
failing with a nil pointer exception due to the missing OwnerInfo field
in ClusterInfo. This cluster condition hasn't been reproduced in healthy
environments, and it is unknown how the CSI configmap came to be
missing. However, the case did expose the missing loaded info as a
potential for causing nil pointer exceptions during corner cases when
code is otherwise correct.
Signed-off-by: Blaine Gardner <blaine.gardner@ibm.com>
The following printcolumns were added
CephBlockPoolRadosNamespace: Phase,
BlockPoolName, Age
CephFilesystemSubVolumeGroup: Phase,
FilesystemName, PinningConfig, Age
Also improved the error messages in
SubVolumeGroupClient
Signed-off-by: NymanRobin <nyman.robin@gmail.com>
Jiffin Tony Thottan
subhamkrai
Blaine Gardner
Travis Nielsen
dependabot[bot]
Michael Adam
Santosh Pillai
Brian Dowling
subham rai
parth-gr
NymanRobin
Satoru Takeuchi
Redouane Kachach
Praveen M
momantech
findmyhappy
parth-gr
Steven Fackler
NymanRobin
clonefetch