This commit adds the ability for backtracing to trace from the itnerrupt to the
task stack, and across nested interrupts. Test cases have also been added.
See merge request !4084
Note: "Test backtrace from abort" reset reason modified by removing abort as a reason.
esp32: update libphy.a to fix interrupt watchdog when WiFi and BT run at the same time and both enable modem sleep (backport v3.1)
See merge request idf/esp-idf!4193
Originally, when doing BLE active scan, Bluedroid will not report adv to
application layer until receive scan response. This option is used to
disable the behavior. When enable this option, Bluedroid will report
adv data or scan response to application layer immediately.
Previously, hardware SHA engine "locks" were mutex semaphores. This meant that the task which
started a particular SHA session (in hardware) needed to finalise that session, or an invalid
FreeRTOS state was created.
Replace with binary semaphore which can be shared between tasks.
Includes a unit test, but unit test doesn't crash even without this fix
(some other unknown condition is required).
Bootloader used to calculate the number of cache pages assuming that
load address was aligned, while in reality load address for DROM and
IROM was offset by 0x20 bytes from the start of 64kB page. This
caused the bootloader to map one less page if the size of the image
was 0x4..0x1c less than a multiple of 64kB.
Reported in https://esp32.com/viewtopic.php?f=13&t=6952.
In some cases, linker could choose to use ROM functions instead of the
ones defined in IDF.
For functions used in ROM stub table, this would lead to infinite
recursion when the corresponding function was called from ROM.
For crypto functions, some of these were modified in IDF, and
incompatible with ROM counterparts.
If zero-overhead loop buffer is enabled, under certain rare conditions
when executing a zero-overhead loop, the CPU may attempt to execute an invalid instruction. Work around by disabling the buffer.
Due to a hardware limitation in ESP32, the first four bytes of some
CSI data is invalid, not the last four bytes.
Correct a mistake of CSI sub-carrier index in documentation.
closes https://github.com/espressif/esp-idf/issues/2494
closes https://github.com/espressif/esp-idf/pull/2493
closes https://github.com/espressif/esp-idf/pull/2496
1. Change bus reset to handle interrupted READ sequences.
2. Slow down I2C to 100khz during reset
3. If a SLAVE device was in a read operation when the bus was interrupted, the SLAVE device is controlling SDA.The only bit during the 9 clock cycles of a byte READ the MASTER(ESP32) is guaranteed control over, is during the ACK bit period.
If the SLAVE is sending a stream of ZERO bytes, it will only release SDA during the ACK bit period. The master(ESP32) cannot generate a STOP unless SDA is HIGH. So, this reset code synchronizes the bit stream with, Either, the ACK bit, Or a 1 bit.
I am stealing this delay coding from @jeremyherbert #2493 pr.
2. Change Bus Reset to handle interrupted READ sequences.
The current code does not handle interrupted READ cycles.
If a SLAVE device was in a read operation when the bus was interrupted, the SLAVE device is controlling SDA.
The only bit during the 9 clock cycles of a byte READ the MASTER(ESP32) is guaranteed control over, is during the ACK bit period.
If the SLAVE is sending a stream of ZERO bytes, it will only release SDA during the ACK bit period. The master(ESP32) cannot generate a STOP unless SDA is HIGH.
So, this reset code synchronizes the bit stream with, Either, the ACK bit, Or a 1 bit.
3. fix typo
correct `sda_id` to `sda_io` in `i2c_master_clear_bus()` @ryan-ma found it. This typo was generated when I manually edited this patch on GitHub, I should have done a Copy/Paste operation!
1. fix bug PHY/RTC functions called in ISR (update phy to v4007)
2. add UnitTest to test it
3. fix task watchdog bug when wifi change channel
4. disable/enable agc to mac deinit/init
5. add UnitTest Job
state and reduce force receiving broadcast data time
1. If receiving beacon which indicates that there is no data
buffered, do not force to receive WiFi data.
2. If receiving beacon which indicates that there is broadcast data
buffered, reduce the time to force receiving broadcast data.
timer_process_alarm function of esp_timer holds a spinlock for the
entire duration of its operation, except for the time when timer
callback function is called. It is possible that when
timer_process_alarm releases the spinlock, a higher priority task may
run and delete the timer. Then the execution will return to
timer_process_alarm, and this will either cause a crash, or undesired
execution of callback after the timer has been stopped or deleted.
To solve this problem, add a mutex which will prevent deletion of timers
while callbacks are being dispatched.
A workaround to reset BBPLL configuration after light sleep. Fixes the
issue that Wi-Fi can not receive packets after waking up from light
sleep.
Ref. https://github.com/espressif/esp-idf/issues/2711
On enabling flash encryption, OTA fails with magic byte error in the second chunk
if the http data is split into two or more chunks and first chunk is less than 16.
This fix includes following changes:
1. Fix the bug that esp_restart()/esp_wifi_stop() sometimes fails in WiFi/BT coexist mode.
2. Add a timer for WiFi stop and stop WiFi forcibly once the timer expires.
1. start an esp_timer on entering sleep to acquire pm_lock before wake up from modem sleep
2. decrease the clock division of XTAL fed to bluetooth low power clock from 32us to 2us period to allow to work under 240MHz Max CPU frequency
3. decrease the minimum sleep duration threshold to allow shorter bluetooth modem sleep period, especially for BLE with short connection interval
4. reconfigure bluetooth baseband(BT-BB) settings after PHY/RF init upon waking up from modem sleep to avoid packet RX/TX performance degradation
Introduced in 9c23b8e5 and 4f87a62f. To get higher speed, menuconfig
options are added to put ISR and other functions into the IRAM. The
interrupt flag ESP_INTR_FLAG_IRAM is also mistakenly set when the ISR is
put into the IRAM. However callbacks, which are wrote by the user, are
called in the master and slave ISR. The user may not be aware of that
these callbacks are not disabled during flash operations. Any cache miss
during flash operation will cause panic.
Essentially IRAM functions and intrrupt flag ESP_INTR_FLAG_IRAM are
different, the latter means not disabling the ISR during flash
operations. New bus_config flag intr_flags is offered to help set the
interrupt attribute, including priority level, SHARED, IRAM (not
disabled during flash operations). It introduced a small BREAK to
IDFv3.1 (but the same as IDFv3.0) that the user has to manually set IRAM
flag now (therefore he's aware of the IRAM thing) to void the ISR being
disabled during flash operations.
1. Fix interrupt watchdog timeout in bluetooth "btdm_bb_isr"
2. Fix BLE assert(512) or assert(1536) in rwble.c at line 222
3. Update librtc.a to fix BLE assert(512) in rwble.c at line 222
The #1 and #2 occurs random.
The #3 bug occurs in certain scenario:
1. If Wifi start softap and BLE is working
2. If wifi start station, but do not use normal station operation, such
as just use espnow, while BLE is working
3. Any other scenario, that wifi works without use software coexist
operation, while BLE is working(such as do advertising and ...)
4. update libcoexist.a version to v1.1.2
The number of runners of integration test is not bottleneck to CI
pipeline performance now. Combine these 2 stages will make integration
test executed even unit test fails. This could help us to collect more
info about test history.
1. replace xunitgen with junit_xml, which can log more info
2. allow test cases to handle junit test report by them own
3. allow test cases to log some info into report via `sysout` tag
This commit resolves a blocking in esp_aes_block function.
Introduce:
The problem was in the fact that AES is switched off at the moment when he should give out the processed data. But because of the disabled, the operation can not be completed successfully, there is an infinite hang. The reason for this behavior is that the registers for controlling the inclusion of AES, SHA, MPI have shared registers and they were not protected from sharing.
Fix some related issue with shared using of AES SHA RSA accelerators.
Closes: https://github.com/espressif/esp-idf/issues/2295#issuecomment-432898137
Fix some wifi bugs
1. Enable RX BAR
2. Fix the bug that ESP32 AP negotiates with iphone to 11g
3. Fix the bug that ESP32 STA has ap_loss because CMCC AP contains two SSID
mdns queries did not work properly when send imeadiately after set_hostname, which cuased reinit of pcb and therefore restarted probing, so search packets were blocked until probing finished
closes#2507, closes#2593
Having two different spinlocks is problematic due to possibly
different order in which the locks will be taken. Changing the order
would require significant restructuring of kernel code which is
undesirable.
An additional place where taking xTickCountMutex was needed was in
vApplicationSleep function. Not taking xTickCountMutex resulted in
other CPU sometimes possibly advancing tick count while light sleep
entry/exit was happening. Taking xTickCountMutex in addition to
xTaskQueueMutex has shown a problem that in different code paths,
these two spinlocks could be taken in different order, leading to
(unlikely, but possible) deadlocks.
1. Fix the bug that disable controller suddenly cause crash when ble is working
2. Fix the bug that when disable controller, it will cause wifi cannot RX, TX timeout, buffer lack and etc.
1. When WIFI task or other high priority task blocks the Bluetooth task, ACL RX buffer will use up, ACL RX buffer ptr will point to null and will never point to a valid adress. Causing errors in Bluetooth.
2. hcimsgs.h used whether flow control is on or off
1. resolve the error in calculating sniff anchor point that result in connection supervision timeout
2. resolve the issue of user case that requires sniff attempt is larger than 0xff
It is possible to utilize some of the routines related to otadata
partition validation, after firmware image is downloaded to RAM. Hence
these routines should be part of app cpu cache, so that they do not
get overwritten by firmware.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
Gitlab CI now allow us to define if a job need to be created by
varialbes. This commit add label to CI jobs, so we can make some jobs
not created in certain scenarios when we trigger pipeline with @bot.
Fix following WiFi bugs:
1. Fix the bug that MIC verification fails on soft-AP mode
2. Modify mesh root to have same behavior as normal WiFi STA in state change
3. Fix the bug that sniffer can't catch control packets
4. Fix crash bug in soft-AP mode
5. Fix ACM(Admission Control Management) bug
1. fix some bugs by previous coex hw blocking bugfix,
such like, rwble.c (64, 0) line 222
2. fix bug that ble scan performance is very low when software coexist
is working.
3. update libcoexist version to v1.1.0
1. remove use EID to distinguish psram voltage
2. 1V8 64Mbit psram and 3V3 64Mbit psram use the same psram driver(standard spi interface)
3. set cs hold time register as 1
1. Add reading psram EID.
2. Configure different clock mode for different EID.
3. add API to get psram size and voltage.
4. Remove unnecessary VSPI claim.
For 32MBit@1.8V and 64MBit@3.3V psram, there should be 2 extra clock cycles after CS get high level.
For 64MBit@1.8 psram, we can just use standard SPI protocol to drive the psram. We also need to increase the HOLD time for CS in this case.
EID for psram:
32MBit 1.8v: 0x20
64MBit 1.8v: 0x26
64MBit 3.3v: 0x46
1. Fix the bug that ESP32 will reject the retry AddBA request frame
if AddBA response frame is failed to sent by WiFi LMAC
2. Fix the bug that AddBA request retrys too frequently
3. Forbid BA session setup for VO queue related TID
Routine `spi_flash_cache2phys` sometimes return incorrect value,
resulting in failure in getting currently running ota partition.
This in turn aborts firmware update process.This issue was more
prominent with SPIRAM enabled cases.
Fix ensures proper cache guards during `spi_flash_cache2phys`, and
also for few other similar APIs.
In addition, `esp_ota_get_running_partition` has also been optimized
to save currently running partition for subsequent invocations.
Fixes https://github.com/espressif/esp-idf/issues/2451
Problem Description
The reporduce steps are as follows:
1.This issue can be reproduced with 4 ESP32 devices, 2 for stations (STA1, STA2) and 2 for soft-AP (AP1, AP2)
2.Configure AP1/AP2 to the same SSID (ssid_xxx)
3.The max allowed WiFi connections of AP1 is configured to 1 and STA1 connects to AP1
4.The AP1 is close to STA2 while AP2 is far away from STA2 (but the STA2 can find the AP2 via scan)
5.STA2 connects ssid_xxx with all scan method
6.The problem will happen on STA2 because it fails to connec AP1 and never connects AP2
Phenmenon
STA fail to connect after send auth or assoc with a wrong status code, but no disconnect event report and can not connect the next one in the envrionment
Root Cause
Because there are some same ssid APs in the evnrionment, when do all channel scan, it will collect all the matched AP in rc list, because rc list is not empty, so it would send disconnect event, however, we didn't do other step such as connect to other one
VNC MR 575
closes https://github.com/espressif/esp-idf/issues/2323
fix the bug following:
1. after disable bluetooth controller, wifi cannot TX/RX any packets.
2. when software coexist working, there's a little ratio cause wifi task
watchdog timeout
3. when software coexist working, there's a little ratio cause bluetooth
cannot receive anything.
feature:
1. add libbtdm_app.a git commit local and remote checking
Known issues:
1. there's still a bug occurs with a very very low ratio cause bluetooth
cannot receive anything. The reproduce interval may great than 3days
~ 1week via 7x24 hours heavy testing.
1. suppport mesh type, mesh ID, router and IE crypt func&key at any time after mesh is initalized.
2. support modify parent at any time after mesh is configured.
3. modify manual networking example.
4. update header file.
5. fix issues in root conflicts handling.
6. add max length of beacon to menuconfig.
7. fix issue when received a beacon without DSSS.
This change removes the earlier limitation of 1984 bytes for storing data-blobs.
Blobs larger than the sector size are split and stored on multiple sectors.
For this purpose, two new datatypes (multi-page index and multi-page data) are
added for entries stored in the sectors. The underlying read, write, erase and find
operations are modified to support these large blobs. The change is transparent
to users of the library and no special APIs need to be used to store these large
blobs.
Backport following WiFi fixes to v3.1:
1. Fix AMPDU RX sequence compitability bug
2. Optimize scan capability in all channel scan
3. Fix some modem sleep bugs
4. Update API to set CSI channel filter and HT_LTF data generating
Allocation was happening later, causing possible use of stack variables
of caller function, which could be invalid.
Signed-off-by: Piyush Shah <piyush@espressif.com>
AVRCP connection binds to A2DP in current implementation, despite the two profiles are\
independent according to specification. AVRCP connection is not necessary to set-up \
if A2DP connection fails to establish
In opening state of AVDTP connection, if SDP client fails to get valid A2DP service record\
from peer SDP server, then do not initiate AVDTP connection request
In pevious implementation, A2DP sink will register an A2DP source Stream End Point(SEP) although the SEP is not\
supposed to be used. Now remove the unused SEP for source so that only one role of A2DP can be supported at one
time. Service record in local SDP server only includes at most one service for A2DP sink role or source
refence to https://github.com/espressif/esp-idf/issues/2284
Before fixing, the tx power in adv data is always 0xeb(-21dbm).
restriction:
If change BLE advertising TX power, please call esp_ble_gap_config_adv_data()
after BLE adv TX power changed.
Later, will implement set BLE advertising TX power via HCI, then the
TX power value in adv data can be update automatically after BLE adv
TX power changed.
Currently CI test environment is complicated, usually includes NIC, AP.
These devices are not used for a lot test cases. Therefore we split the
test environment, remove unnecessary devices. Then it will be easier to
create CI runners.
As the bluedroid original implmentation of BR/EDR and BLE dual mode about discovery mode,
when set discovery mode for BR/EDR, it will stop ble advertising.
Reference to https://github.com/espressif/esp-idf/issues/2306
Allows OTA updates to be secured via signature checks, without requiring the overhead or complexity
of a full secure boot implementation.
Uses same signing mechanisms (build system and/or espsecure.py as Secure Boot).
Requires:
* [ ] More testing
* [ ] Documentation
The following commit rewrites the ESP-MESH docs. This commit includes
new diagrams and a structure approach to the mesh docs. Some mesh api references
have also been modified.
Some APs transmit AMPDU and MPDU by turns. Moreover, the sequence
numbers of AMPDU and MPDU are out of order, e.g. MPDU(1253) -
AMPDU(1251, 1252) - MPDU(1254) - AMPDU(1255, 1256). In order to
receive both AMPDU and MPDU in order, MPDU must be reordered with
AMPDU.
1. new APIs: esp_mesh_get_subnet_nodes_num() and esp_mesh_get_subnet_nodes_list().
2. fix hard to find the parent during connect.
3. disable Wi-Fi channel switch function.
4. fix a typo of MESH_EVENT_NO_PARENT_FOUND.
Multiple modules register their callback BTA_GATTS_AppRegister().
If any of the callbacks do not free the allocated pointer in
BTA_GATTS_CONF_EVT event, then this can result in memory leak.
So, free the pointer after the callback function is called and remove
the calls to free in the callback functions as it is now not required
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
Fix following WiFi bugs:
1. Shouldn't scan when connect
2. Check beacon length in modem sleep
3. Fix the bug that AP may deauth wrong station when inactivity timer expires
4. Fix the bug that WiFi assert the system when receiving empty MCS in association response frame
We have fixed a bug in test script. Before that, we didn't do strict check when generate the mesh tree, which makes the test pass.
Temp disable these cases, to let CI pass before bug fixed.
For pins 32 and up the BIT(nr) macro used here overflowed,
causing undetermined GPIO pins to be reset.
Example: freeing SPI device/bus where CS is on pin 33
caused debug UART to cease communication, TXD0 was
disabled.
Fixed as BIT64(nr) macro, to be used elsewhere as needed.
For example in definitions like GPIO_SEL_32..GPIO_SEL_39.
Hardware implements conditions LE, LT, GE, and conditions EQ and GT
are implemented in the assembler by emitting two JUMPS instructions
with other conditions.
Component which includes component_ulp_common.mk may also need to set
some of the same COMPONENT_XXX variables. Logically, we should combine
the lists of files to embed, ldflags, extra include dirs, etc.
Fixes https://github.com/espressif/esp-idf/issues/2157.
The argument to ulp_run should be expressed in 32-bit words. Both the
address of ulp_entry and RTC_SLOW_MEM already are uint32_t*, so their
difference is the difference in addresses divided by sizeof(uint32_t).
Therefore the extra division by sizeof(uint32_t) is not needed.
1. Add the 100 times test when the private key is generated by the random number;
2. Add the bt components to the unit-test-app/config directory.
3. Added the bt unit test case to CI.
1. modify parent switch mechanism.
2. fix non-root doesn't clear the layer value in nvs.
3. fix retransmit the remove announcement packets.
4. add API esp_mesh_flush_upstream_packets().
5. automatically adjust passsive scan time based on the change of beacon interval.
* "git clone" command and a small version header are generated
depending on git properties.
* Add Versions page with details about each version
* Make it clear using master branch is living on the "bleeding
edge"
Backport following bug fixes to v3.1:
1. Bug fix of may connect to wrong AP in all channel scan
2. Station state machine change and fix ap loss
3. Add compatible to ccmp encryption
4. Update libphy.a to v3960:
4.1 Decrease phy_init time from 900us to 347us in sleep wakeup
4.2 Fix RX STBC initialization
4.3 Modify set_chan function to fix interrupt watchdog issue
5. Fix several wpa2 enterprise issues
5.1 Fix heap corrupted bug
5.2 Fix memory leak bug
5.3 Make wpa2 enterprise thread-safe
Closes https://github.com/espressif/esp-idf/issues/1569
6. Bugfix of coex wifi pm
* spi_flash_mmap_pages needs pages array to be in internal memory.
Document and check this.
* Fix a bug that spi_flash_mmap did not allocate pages array in
internal memory.
* Minor style fixes: const-ify pages argument of spi_flash_mmap, add
spaces around operators, mark output arguments with [out].
Closes https://github.com/espressif/esp-idf/issues/2229.
esp_http_client: fixed http chunked encoding packet loss & add check data before read for ssl transport (backport v3.1)
See merge request idf/esp-idf!2952
This change adds a check for compatibility between the nvs version
found on nvs flash and the one assumed by running code during nvs
initialization. Any mismatch is reported to the user using new error
code ESP_ERR_NVS_NEW_VERSION_FOUND.
1. The test step for error code REASON_ASSOC_EXPIRE is not reliable. SoftAP
could also send error code WIFI_REASON_NOT_AUTHED
2. STA will be disconnected now if softAP restart DHCP server
1. when one task do deinit/init/disable/enable, especially different cpu
core, it may cause controller crash in ISR handler
2. fix while BLE is scanning, bluetooth controller is disabled cause BLE
scan is not abort.
If project.mk is included twice in recursive invocation of Make, some
variables defined on the first pass will not be redefined on the
second pass. Rather than cleaning up these variables before calling
Make recursively, don’t include IDF project.mk at all, if one of the
ut- targets is requested.
We found some SD card on Raspberry Pi could have very bad performance.
It could take seconds to save small amount of data.
If the DUT receives data and save it as log, then it stops receiving data until log is saved.
This could lead to expect timeout. As an workaround to this issue,
``BaseDUT`` class will create a thread to save logs.
Then data will be passed to ``expect`` as soon as received.
Test report is not used as expected:
1. we rarely download and use test report
2. current test report method doesn't handle large amount data well,
need to be replaced by other methods
Test report also make test jobs allow to fail. It breaks the
original flow of Gitlab CI and make user confused.
If we have the partition table without any ota_apps but in ota_data have
valide entry, in this case we get an error(hang). This commit fix this
case. If bs->app_count is zero when selecting the factory app.
Closes https://github.com/espressif/esp-idf/issues/2218
Because address space is mapped in 64KB pages, it was possible for unauthenticated data after the
app .bin to become mapped into the flash cache address space.
This problem is solved by 2 changes:
* "esptool elf2image --secure-pad" will pad the image so that the signature block ends close to the
64KB boundary. Due to alignment constraints it will be 12 bytes too short after signing (but
with flash encryption, these 12 bytes are still encrypted as part of the last block and can't be
arbitrarily changed).
* By default, secure boot now requires all app partitions to be a multiple of 64KB in size.
- call rtc_gpio_init for pins which aren't configured as RTC by default
- for RTC IOs 16 and 17, read higher part of the input register
- automatically convert GPIO number into RTC IO number
- use ulp_set_wakeup_period instead of writing to register
Perviously host send_auto_stop flag would be set for every data
transfer over 1 block long. This caused stop commands to be sent
after CMD53, which shouldn't be done. Fix by adding an explicit list
of commands for which send_auto_stop should be set.
Since 94250e42a0, UART output is suspended when entering sleep mode
(deep or light sleep). This makes sense for light sleep, where sleep
normally takes small amount of time, and flushing the UART would add
a lot of latency. But this breaks existing behaviour for deep sleep,
where UART output was previously sent out before entering sleep mode.
Closes https://github.com/espressif/esp-idf/issues/2145
1. Move channel to the first row of the table.
2. Remove the condition of HT20/HT40 for they are determined by
secondary channel.
3. Clean up the CSI table.
Send the Goodbye packet while removing an mDNS service as an "Authoritative" packet so
that the listeners remove the service from their records immediately.
INTERRUPT and CCOUNT registers will change outside of program control.
Making the inline assembly used to read these registers volatile
indicates this fact to the compiler.
Fixes https://github.com/espressif/esp-idf/issues/2127
51e42d8e92
introduced filtering options which handles the last (unterminated) line
with a delay. This introduced poor performance for console applications
when the user interacts with the ESP32 device in the same line because
there is an artificial delay for each key-press.
bb152030a0
decreased the delay but there are still delays for each key-presses.
The current fix makes only one delay per line instead of each
key-presses. When an unterminated line is detected then no more
"delayed" print is used for the given line.
Fixes https://github.com/espressif/esp-idf/issues/2054
1. fix BLE connection missing in coex mode
2. modify other parameters to make coex priority more reasonable
3. fix modem sleep procedure trap cause Wifi disable RF when BT is
working. Such cause that BR/EDR is difficult to be connected, BLE
connection stability decrease and so on.
4. modify BR/EDR coexist duration to imrove BR/EDR connect success
ratio.
5. Due to the hardware coexist bug, BLE scan interval/window should
be less than 0x100(about 160ms). Therefore, it will cause BLE cannot
scan any advertising packet while WiFi have higher priority
behaviour(such like RX beacon, scan, TX/RX VO packets and etc.).
1. esp_ble_remove_bond_device will only remove BLE bond key and disconnect BLE device.
2. esp_bt_gap_remove_bond_device will only remove BT bond key and disconnect BT device.
A cherry-pick of MR !2562
1. add APIs to set/get announce interval values.
2. add API to enable/disable the min rate to 6Mbps for data packages.
3. add APIs to set/get RSSI threshold values.
4. fix ap_loss.
Moved useful functions from wrapped assert functions, because option `CONFIG_OPTIMIZATION_ASSERTIONS_DISABLED=y` will remove this functions.
Closes https://github.com/espressif/esp-idf/issues/2068
IDF had two defines ESP_PARTITION_TABLE_OFFSET and ESP_PARTITION_TABLE_ADDR. They were the same and equal by 0x8000.
A define ESP_PARTITION_TABLE_ADDR was removed from IDF.
A define ESP_PARTITION_TABLE_OFFSET depends on option CONFIG_PARTITION_TABLE_OFFSET in Kconfig.
Now using only #define ESP_PARTITION_TABLE_OFFSET CONFIG_PARTITION_TABLE_OFFSET
This change allows readonly FATFS to be mounted without wear levelling
support. This will provide the customers a simple way to mount FATFS images
generated on host and flashed onto the chip during factory provisioning.
Since NVS encryption is not supported yet and NVS entry size is limited,
the change will provide an easy alternative for securing the provisioning data
by just marking FATFS parition as encrypted.
The IDF monitor waits for one second before printing the last
unterminated line. This is necessary for the correct filtering.
However, this causes poor performance, for example, in the case of the
system/console example.
This fix reduces the waiting time which improves the response time of
the console example and doesn't seem to influence the monitor filter.
Closes https://github.com/espressif/esp-idf/issues/2054
* a missing pointer increment caused error, if available was > 0 after the first iteration of while(available) loop.
* changed memory allocation strategy from large fixed size (RFCOMM_DATA_BUF_SIZE) to just the needed
size, which will be below MTU
Cherry-picked from https://github.com/espressif/esp-idf/pull/1923/
Since commit 94250e4, EXT0 wakeup mechanism, when wakeup level was set
to 0, started waking up chip immediately after entering deep sleep.
This failure was triggered in that commit by a change of
RTC_CNTL_MIN_SLP_VAL (i.e. minimum time in sleep mode until wakeup
can happen) from 128 cycles to 2 cycles.
The reason for this behaviour is related to the way input enable (IE)
signal going into an RTC pad is obtained:
PAD_IE = (SLP_SEL) ? SLP_IE & CHIP_SLEEP : IE,
where SLP_IE, SLP_SEL, and IE are bits of an RTC_IO register related
to the given pad. CHIP_SLEEP is the signal indicating that chip has
entered sleep mode.
The code in prepare_ext{0,1}_wakeup did not enable IE, but did enable
SLP_SEL and SLP_IE. This meant that until CHIP_SLEEP went high, PAD_IE
was 0, hence the input from the pad read 0 even if external signal
was 1. CHIP_SLEEP went high on the 2nd cycle of sleep. So when
RTC_CNTL_MIN_SLP_VAL was set to 2, the input signal from the pad was
latched as 0 at the moment when CHIP_SLEEP went high, causing EXT0
wakeup with level 0 to trigger.
This commit changes the way PAD_IE is enabled: SLP_SEL and SLP_IE are
no longer used, and IE is set to 1. If EXT0 wakeup is used, RTC_IO is
not powered down, so IE signal stays 1 both before CHIP_SLEEP goes
high and after. If EXT1 wakeup is used, RTC_IO may be powered down.
However prepare_ext1_wakeup enables Hold on the pad, locking states
of all the control signals, including IE.
Closes https://github.com/espressif/esp-idf/issues/1931
Closes https://github.com/espressif/esp-idf/issues/2043
For some test configurations, not all tests need to be run. This
change allows adding a comment in the configuration file of the
following form:
unit-test-app makefile will use it to determine which components to
build. If the comment is not present, all components will be built
(TESTS_ALL=1).
Also add test configuration for libsodium. It is a separate test
configuration due to the large binary size generated when building
libsodium tests.
Previously the loop in esp_timer_impl_set_alarm was necessary to catch
the case when timer count wraps around (goes from 2^32 - 1 to 0).
Since ALARM_OVERFLOW_VAL was reduced from 2^32 - 1 to 0xefffffff,
this is no longer necessary.
Fixes https://github.com/espressif/esp-idf/issues/1891
When ‘fetch’ strategy is used, Gitlab removes untracked files before
checking out new revision. However if the new revision doesn’t
include some of the submodules which were present in the old
revision, such submodule directories would not be removed by the
checkout. This extra step ensures that these stale submodules are
removed.
Allows you to move the partition table, it gives more space for the bootloader.
Added a new utility - parttool.py. This utility can search for the offset and/or size of the partitions by name and type/subtype. Use for getting APP_OFFSET and PHY_DATA_OFFSET.
The linker(esp32.bootloader.ld) made changes that allow you to write a custom bootloader code more.
TW14125
spi test: Prime the flash cache before each test to minimise flash cache misses.
VFS performance test: Increase the number of runs to minimise influence of an isolated bad run.
The old command caused was incorrect (x is “examine”, not “execute”)
and caused GDB register update only by chance. This replaces it with
“flushregs” command which purpose is exactly that — force GDB to
fetch registers from the remote.
Makes spiffs component runnable on host. Depends on the host library build
of flash emulator. Includes a basic sanity test of
mounting a volume, opening a file, writing to the file, reading the file,
closing the file and unmounting volume.
Makes fatfs component runnable on host. Depends on the host library build
of wear levelling and flash emulator. Includes a basic sanity test of
mounting a volume, opening a file, writing to the file, reading the file,
closing the file and unmounting volume.
Makes the entirety of the wl API runnable on host. Flash emulator
is separated into spi_flash component directory to be reused by
other storage components.
Before entering the deep sleep, the RTC and FRC counters are synchronized. Updating the boot_time.
Added a unit test for this case.
Fixed warnings for MULTIPLE_STAGES
Closes https://github.com/espressif/esp-idf/issues/1840
1. Fix the WiFi/BT coexist bug
2. Fix WPA2 enterprise example crash bug
3. Add size and version check for crypto type struct
4. Add MD5 check for crypto type header file
This fix is for compatibility with lwip_select(). It moves the lock to
UART which is the only VFS driver which is implemented and is not
"thread-safe".
These versions of conf/mconf are forked from the upstream, and the CMake system allows mconf-idf to
be installed externally on the path. So the best option is to rename.
Includes changes to Windows installer for v1.1
in the include file esp_ota_ops.h "esp_partition.h" is included.
This is from spi_flash so component that requires app_update also will need that
this fixes this error:
In file included from ../components/esp32-homie/ota.c:11:0:
/esp-idf/components/app_update/include/esp_ota_ops.h:22:27: fatal error: esp_partition.h: No such file or directory
Signed-off-by: Nicola Lunghi <25422924+nicola-lunghi@users.noreply.github.com>
Merges https://github.com/espressif/esp-idf/pull/1947
Don't show the "Python 2 interpreter" option in menuconfig when using CMake.
This is a stop-gap until we support Python 2 & 3 together in ESP-IDF (soon).
Closes https://github.com/espressif/esp-idf/issues/1924
This function speeds up or slows down the system clock in order to make a gradual adjustment. This ensures
that the calendar time reported by the system clock is always monotonically increasing, which might not happen
if you simply set the clock.
The delta argument specifies a relative adjustment to be made to the clock time. If negative, the system clock is
slowed down for a while until it has lost this much elapsed time. If positive, the system clock is speeded up for a
while.
If the olddelta argument is not a null pointer, the adjtime function returns information about any previous time
adjustment that has not yet completed.
The return value is 0 on success and -1 on failure.
To stop the adjustement, call the function settimeofday(current_time).
When using multiple sockets, some of them could be incorrectly removed
from the fd_sets before passing these fd_sets forward to the socket
select function.
Closes https://github.com/espressif/esp-idf/issues/1987
Added feature:
- reset firmware to Factory app.(by long pressing of the button)
- boot Test app. (by long pressing of the button)
- Added feature erase data partitions from factory reset.
TW10281
TW10280
Will give hint when any job failed to assign:
```
Please add the following jobs to .gitlab-ci.yml with specific tags:
* Add job with: psram, ESP32_IDF, UT_T1_1
* Add job with: psram, ESP32_IDF, UT_T1_1
```
We have built unit-test-app with different configs.
Currently we use the config name as tags to match runners.
It's not easy to add new configs (need to update tags to existed runners).
Now we'll parse required test runner tags from `sdkconfig` file.
For example, if config enables `CONFIG_SPIRAM_SUPPORT`, then it requires `psram` tag.
This will make adding new configs easier.
In this commit we change the one behavior of assign test: match keys of
cases should be exactly the same with job tags. This fixes cases select
jobs include their tags, and jobs requires those tags can't be assigned.
1. add mesh_assoc_t to esp_mesh_internal.h file.
2. rename "node" to "device" in esp_mesh.h.
3. add MESH_EVENT_SCAN_DONE event.
4. add APIs esp_mesh_scan_get_ap_record() and esp_mesh_scan_get_ap_ie_len() to get scan results.
5. modify API esp_mesh_set_self_organized() by adding parameter "select_parent".
6. modify API esp_mesh_set_parent() by adding parameter "parent_mesh_id"
7. add manual networking example.
1. Store the calibration data to NVS if PHY does full calibration because of calibration data checksum failure
2. Pass the station's mac to PHY for checksum calculation
This includes changing the picture of JTAG jumper block by removing the jumper on S_TDI. It has been reported by a number of users that removing this jumper fixes random communication issues observed in OpenOCD.
A new method of workaround an error with DPORT is to ensure that the APB is read and followed by the DPORT register without interruptions and pauses. This fix places this implementation in the IRAM to exclude errors associated with the cache miss.
Earlier they have to be selected at the compile time through sdkconfig.
A2DP sink and source application tested with this change.
Signed-off-by: Amey Inamdar <amey@espressif.com>
Add error handling for http client
set ssid password correct with Example_WIFI test, and clear password before free
Fixed the CI failure due to HTTP errror names
driver(i2c, rmt): Add xQueue and xSemaphore static allocation support when intr_alloc_flag set to ESP_INTR_FLAG_IRAM.
See merge request idf/esp-idf!2335
This fixes multiple bugs with ring buffers and re-factors the code. The public
API has not changed, however the underlying implementation have various private
functions have been changed. The following behavioral changes have been made
- Size of ring buffers for No-Split/Allow-Split buffers will not be rounded
up to the nearest 32-bit aligned size. This was done to simplify the
implementation
- Item size for No-Split/Allow-Split buffers will also be rounded up to the
nearest 32-bit aligned size.
The following bugs have been fixed
- In copyItemToRingbufAllowSplit(), when copying an item where the aligned
size is smaller than the remaining length, the function does not consider
the case where the true size of the item is less than 4 bytes.
- The copy functions will automatically wrap around the write pointers when
the remaining length of the buffer is not large enough to fit a header, but
does not consider if wrapping around will cause an overlap with the read
pointer. This will make a full buffer be mistaken for an empty buffer
closes#1711
- xRingbufferSend() can get stuck in a infinite loop when the size of the
free memory is larger than the needed_size, but too small to fit in the ring
buffer due to alignment and extra overhead of wrapping around.
closes#1846
- Fixed documentation with ring buffer queue set API
- Adding and removing from queue set does not consider the case where the
read/write semaphores actually hold a value.
The following functions have been deprecated
- xRingbufferIsNextItemWrapped() due to lack of thread safety
- xRingbufferAddToQueueSetWrite() and xRingbufferRemoveFromQueueSetWrite()
as adding the queue sets only work under receive operations.
The following functions have been added
- xRingbufferReceiveSplit() and xRingbufferReceiveSplitFromISR() as a thread
safe way to receive from allow-split buffers
- vRingbufferGetInfo()
Documentation for ring buffers has also been added.
Add function xRingbufferCanRead & xRingbufferCanWrite
to be able use queue sets. Without it is not possible
to check to which ringbuffer returned semaphore belongs.
1. provide options for bluetooth low power mode
2. provide two options for bluetooth low power clock: main XTAL and external 32kHz XTAL
3. provide function and callbacks to control bluetooth low power mode, including enable/disable sleep, software wakeup request, low power clock settings, check power state, etc
4. modify vhci API vhci_host_send_packet to use blocking mode
5. note that DFS and bluetooth modem sleep can not be used together currently.
In situations where idle task runs a lot of idle hooks or cleanup code
(due to pthread local storage, etc) it can use more than 1KB of stack.
(I think the trigger is if a context switch happens at the right point
in the TLS cleanup).
Also removes an sdkconfig.default which accidentally set all config items,
including this stack size.
Added .rtc_noinit and .noinit section definitions into linker file /esp32/ld/esp32.common.ld.
The macro __NOINIT_ATTR, RTC_NOINIT_ATTR declared in esp32/esp_attr.h file.
Added unit test file to test added behavior for noinit variables and its attributes.
Added documentation changes for new added attributes.
Make some corrections after code review:
The linker file has been corrected to place noinit section before bss_start to make it safer.
Documentation file has been modified to clarify reset behavior of allocated data .
Corrected typos in test_noinit.c and removed assertion of noinit variable to avoid possible issues with ROM boot loader memory allocation.
The linker file has been corrected to place noinit section before bss_start to make it safer.
Documentation file has been modified to clarify reset behavior of allocated data .
Corrected typos in test_noinit.c and removed assertion of noinit variable to avoid possible issues with ROM boot loader memory allocation.
Update test_noinit.c file to address RTCWDT_RTC_RESET reset reason instead of POWERON_RESET.
Test optimized to pass automated unit testing.
esp32: Add .noinit and .rtc_noinit sections to the linker script
Update of general-notes.rst documentation to fomat examples as code and attributes as identifiers.
Test test_noinit.c corrected to pass automated testing (support ofTEST_CASE_MULTIPLE_STAGES())
https://ezredmine.espressif.cn:8765/issues/15878
1. remove rc when ap not found
closes issue: https://github.com/espressif/esp-idf/issues/1797
2. allocate mimo packet to internal memory
3. use FRC2 timer instead of WDEV_NOW() for modem sleep to calculate
TBTT time.
It fixes the bug that TBTT will be incorrect if beacon is lost.
If the RTC crystal is bad or has no matched capacitance, then you do not need to start such the crystal. It is necessary to determine this case, output an error (about impossibility to start from the oscillator) and start from the internal RC of the chain.
Reduced the default value of the number of bootstrap cycles. Because we can oscillating the oscillator which then stops. (in Kconfig). Changed from 100 to 5.
The number of calibration cycles has been increased. It is the main criterion for estimating the launch of an oscillator. A large increase leads to an increase in the load time, as well as the stability of recognition of this case. (in Kconfig).
Changed from 1024 to 3000.
1. configs are not functional
* decorator will be executed when search case, need to set default config before search case.
2. fix DUT encode/decode errors
* python3 serial don't support write string/unicode, need to convert to bytes first.
* python2 string could failed to encode/decode non-acsii chars
3. fix bug that log folder not created
4. fix bug that test suite name is not correctly passed:
* the keyward arg should be `test_suite_name` not `test_name`
5. fix bug that test stopped on failed case
6. fix DUT `read` don't return all data cache
* `_DataCache.get_data` should first copy all data from queue to data cache and then return to user.
7. fix bug that `expect_all` failed even all expected item passed
8. optimize error info for expect
* print pattern for regular expression when match failed
9. fix bug that set default config doesn't work
1. Attenuator: control programmable attenuator
2. PowerControl: control APC PDU to power on/off devices
3. LineChart: use matplotlib to draw line chart
This fixes errors logged on the console: sdmmc_req:
handle_idle_state_events unhandled: 00000004 00000000
The issue happens if "data done" event occurs before "command done".
State machine code did not check *which* event occurred in
SENDING_CMD state, and went to IDLE or SENDING_DATA state on any
non-error event. In this case, we can't process "data done" event
until command has completed. This change introduces "unhandled event"
mask, which is carried over from one run of process_events to the
other. This allows waiting for the "command done" event to complete,
and then process "data done" event.
Ref TW17126.
CMD53 in byte mode supports transfers of any number of bytes between 1
and 512. This change removes limitation that the number of bytes must
be divisible by 4. Host quirk, that such transfers must be split into
two commands (one for the aligned part and the other one for
unaligned) is taken into account.
When two CPUs read the area of the DPORT and the area of the APB, the result is corrupted for the CPU that read the APB area.
And another CPU has valid data.
The method of eliminating this error.
Before reading the registers of the DPORT, make a preliminary reading of the APB register.
In this case, the joint access of the two CPUs to the registers of the APB and the DPORT is successful.
As of now, when Bluetooth debugs are enabled, all the messages are
mapped to BT_PRINTF which is mapped to ESP_LOGE. Hence, make monitor
shows all logs in red color which might lead to missing the actual
errors
This patch maps the Bluetooth messages to appropriate ESP_LOG* messages
and improves readability.
Also, make the BT trace level be configurable in menuconfig, so that
each layer of bt trace can be enabled/disabled.
Finally, add debug log control for BTC, OSI, BLUFI and clear up
Bluetooth debug logs.
So, with this the method of enabling Bluetooth logs is as follows:
1. make menuconfig -> Component config -> Bluetooth -> Bluedroid Enable
-> BT DEBUG LOG LEVEL -> set trace level for every layer of BT
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
If the allocated interrupt list is not empty and the new item will be inserted
as the header of the list, insert_vector_desc() causes crash because pre is
null. This commit fix this issue.
1. Fix the duty fade check issue reported from https://github.com/espressif/esp-idf/issues/1914
2. Fix the duty overflow issue when duty_scale is set to 1.
3. Fix the duty fade error when a fade operation is under way. We must configure a new duty setting after the previous fade operation has finished due to hardware limit.
4. Add thread-safe version APIs to set duty and fade.
5. Correct the duty range in driver.
It has been observed that, if external SPIRAM is enabled, then under
certain scenarios (e.g. internal memory being too much fragmented),
I2S tx/rx descriptors can land in external SPIRAM and hence resulting
in failure in DMA. Adding explicit capability to allocate in only DMA
capable memory.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
change some API function to throw event:
esp_wifi_deauth_sta
esp_wifi_get_country
esp_wifi_ap_get_sta_list
esp_wifi_sta_get_ap_info
esp_wifi_stop
esp_wifi_get_channel
esp_wifi_get_protocol
esp_wifi_get_bandwidth
ALT header files for sha1, sha256, sha512 are only supposed to declare
mbedtls_sha1_context data structure. Function prototypes should come
from original header files.
The following mbedTLS APIs have been deprecated and replaced with the
new ones which return error codes:
mbedtls_shaX_starts -> mbedtls_shaX_starts_ret
mbedtls_shaX_update -> mbedtls_shaX_update_ret
mbedtls_shaX_finish -> mbedtls_shaX_finish_ret
mbedtls_shaX_process -> mbedtls_shaX_internal_process
Update hardware implementations of SHA functions, and other IDF
components which used above functions, to use new versions.
When light sleep is started, the other CPU gets halted using DPORT
stall mechanism. This can happen while it is inside an esp_timer
critical section, which may lead to a deadlock. This change adds
functions to take and release esp_timer lock before entering
DPORT critical section, preventing the deadlock.
1. Add error log if failed to store calibration version/mac/data
2. Change the NVS calibration version/mac/data store sequence
3. Pass the init_data instead of NULL to esp_phy_rf_init() in esp_phy_load_cal_and_init()
Currently when page is being freed, items are individually moved from
FREEING page to ACTIVE page and erased. If power-off happens during the
process, the remaining entries are moved to ACTIVE page during recovery.
The problem with this approach is there may not be enough space on
ACTIVE page for all items if an item was partially written before
power-off and erased during recovery. This change moves all the items
from FREEING to ACTIVE page and then erased the FREEING page, If
power-off happens during the process, then ACTIVE page is erased and the
process is restarted.
Refactor IDF "project" functionality under a wrapping of the default
"project" command, so we can tweak it a bit...
Will need more testing in other environments.
* Philosophical: "explicit is better than implicit".
* Practical: Allows useful errors if invalid directories given in components as the defaults aren't
always used. Also trims the -I path from a number of components that have no actual include
directory.
* Simplifies knowing which components will be header-only and which won't
1. Change all the hash used from the coap module to generated by the bluedroid module directly.
component/bt: Added the <string.h> include file to the gattc_co module to avoid compile error.
component/bt: optimiz the code
component/bt: optimiz the code.
component/bt: added the l2c change.
component/bt: Added the modified.
component/bt: change the indicate callback function.
component/bt: added the BLE throughput test gattc & gatts example.
component/bt: Change the sdkconfig.default CONFIG_GATTS_NOTIFY_THROUGHPUT setting.
component/bt: Change the throughput_client_task delay method.
component/bt: change the btu task size from 4096 to 5096
comonent/bt: close the print when congest.
component/bt: Added the CPU frequency set method to the readme file.
component/bt: Change the gatts_demo_char1_val to gl_profile_tab[PROFILE_A_APP_ID].char_handle to avoid make error.
example/ble_throughput: Added the Readme explanation.
component/bt: Added the bt lib change.
component/bt: Update the bt lib & Change the LOG level from ERROR to DEBUG when congest.
component/bt: Fixed the bug of timer start assign error.
component/bt: Change back the gattc & gatts demo with same as the master.
example/ble_throughput: Fixed the bug when prepare write of the ble throughput.
component/bt: Update the check_sum algorithm.
component/bt: Change Added the path when used the include file of "l2cdefs.h" & "l2c_api.h".
example/throughput_client: Added the Freertos related header files to ble throughput client demo to avoid compile error.
1. add the L1 include path with a prefix, such like osi/list.h, stack/a2d_api.h and etc.
2. modify component, only bluedroid/api/include/api is export to another component and application,
other include path just for bluedroid used
3. put bluedroid/include into common/include/common, so the root directory of bluedroid have no include path.
4. modify doxygen to use esp_bt.h and redirect to
component/bt/bluedroid/api/include/api/
fix compile
Unit test runner expects to see the test name echoed after test
selection is made. If the unit test immediately goes into sleep mode,
UART output will not be complete, and test runner will not see the
test name. This flushes the stream buffer and waits for UART FIFO to
be empty before starting the test.
Additionally some parts of code used unity_printf and some used
printf. Since unity_printf was only useful during very early tests
when newlib was not available, replace all its usages with printf.
Disables app image integrity checks when running under OpenOCD control.
Allows setting breakpoints in flash before application start (just after reset).
Command response tokens can be delayed from the original command by 1
to 8 bytes. In 4a2489b9, handling for delayed tokens was added for
normal (no data) commands, and data read commands. This adds handling
for delayed commands for data write commands.
Currently when MAX_STATION limit in DHCP config is set to N, dhcp server
issues only N-1 IP addresses. This is problematic from customer
perspective if both SoftAP MAX_STATION and DHCP MAX_STATION limit is set
to same value. With this change DHCP server can issue N addresses that
is inline with the set limit.
Closes TW<20556>
Previous version of the code only connected CD and WP to the
peripheral, in fact the hardware does not use the values of these
signals automatically. This adds code to read CD and WP values when
command is executed and return errors if card is not present, or
write command is executed when WP signal is active.
Ideally suited for generating a binary externally, containing key-value pairs specific
to device manufacturers. Utility allows creation of a binary, compatible
with NVS structure, which can be separately flashed onto a new
partition. This helps device manufacturers set different values for
different devices, e.g. serial numbers, but using a single firmaware
image.
1. Bootloader reads SPI configuration from bin header, so that the burning configuration can be different with compiling configuration.
2. Psram mode init will overwrite original flash speed mode, so that users can change psram and flash speed after OTA. 3. Flash read mode(QIO/DIO…) will not be changed in app bin. It is decided by bootloader, OTA can not change this mode.
4. Add read flash ID function, and save flash ID in g_rom_flashchip
5. Set drive ability for all related GPIOs
6. Check raise VDDSDIO voltage in 80Mhz mode
7. Add check flash ID and update settings in bootloader
8. Read flash ID once and keep in global variable
9. Read flash image header once and reuse the result
Tested cases:
1. Test new and old version of bootloader
boot Flash 20M —> app Flash 80M + Psram 80M
boot Flash 40M —> app Flash 80M + Psram 80M
boot Flash 80M —> app Flash 80M + Psram 80M
boot Flash 20M —> app Flash 80M + Psram 40M
boot Flash 40M —> app Flash 80M + Psram 40M
boot Flash 80M —> app Flash 80M + Psram 40M
boot Flash 20M —> app Flash 40M + Psram 40M
boot Flash 40M —> app Flash 40M + Psram 40M
boot Flash 80M —> app Flash 40M + Psram 40M 2. Working after esp_restart reboot.
* Move smartconfig to its component directory, it should be possible to override
this as whole component
* Fix few header includes related to lwIP networking stack
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
If static task cleanup option is enabled, then before invoking application
defined `vPortCleanUpTCB` hook, pthread specific cleanup is performed.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
By default, any job will run unless a filter is given, in that case
the filter will determine if the job should run or not. Some jobs do
not need to be run by default, and should only be triggered using the
bot. For such jobs, BOT_NEEDS_TRIGGER_BY_NAME can added to
environment variables.
1. Change all the gattc API && bta gattc layer.
2. Debug the code and change the btc_ble_gattc_get_db method.
3. Change the gatt read API interface.
4. Reconstruction the BTA_gattc_cache code.
5. Change back the bluedroid_get_status to marco.
6. Change the gattc docs format.
7. Change the docs format.
8. fix the read char value bug.
9. change the gattc_get_attr_count method.
10. Change back the bta_gattc write ccc code.
11. Change the gattc api docs format
12. Change the gattc API docs.
13. Change the prepare write descriptor method to avoid the exection.
14. modify gatt clinet demo with new API
15. Change the p_src_data->read.p_value to avoid exection.
16. Change the bugfix of gattc unreg for the notify.
component/bt: Added the serch service res start_handle & end_handle to the result.
component/bt: Added the bta_gattc_cache_write when gatt discovery complete.
component/bt: Added the bta_gattc_cache_write declaration.
component/bt: Added the comments for esp_ble_gattc_cache_refresh API.
component/bt: Change the spelling errors & some comment error.
component/bt: fix bug of get gattc cache address list error.
1. Change the esp_bluedroid_get_status to macro;
2. added the malloc & free for the get_addr_list
component/bt: Added the addr_info->ass_addr == NULL Judgment to prevent crashes in the bta_gattc_co_cache_find_src_addr function.
component/bt: Fixed following gattc cache bugs
1. gattc can't refresh the gattc cache in the gatt discover state;
2. remove the nvs_get_blob in the cache address init function;
3. added the nvs_set_blob return value judgment in the cache address save function;
4. added the list_new when ass_address is NULL;
5. Change the ass_address list remove method to fix the ass address can't remove bug.
1. fix issues on sending beacon caused by too much tx retries on other packets.
2. modify not to scan if rc exists when connect.
3. modify scan dwell time to default 120ms fo root.
Need to make the bootloader modular so that users can redefine its functional part.
- refactoring and moving functions to the bootloader_support component
- Changed function to `void` bootloader_utility_load_image(...);
TW19596
Current code for recovery after power-off do not clean-up partially
erased items for FULL pages. If the erasure was part of modification
operation, this gets luckily cleaned-up because of duplicate detection
logic. For erase-only operation, the problem still exists. This patch
adds the recovery for FULL pages also.
Closes TW<20284>
With V=0, build process would print “including .../Makefile.projbuild" lines, causing problems for print_flash_cmd target.
The issue was due to the way macro expansion works in make. To delay evaluation of info function until the execution of expanded block, two dollar signs are required.
Test for print_flash_cmd target added.
When erasing a variable length item with an incorrect CRC32, the span
value of the item can not be trusted, so the item will be erased with
span = 1. Subsequent entries represent the data of the variable
length item, and these will be treated as separate items. For each
entry CRC32 is checked, the check most likely fails (because the
entry contains arbitrary data, and not a proper NVS item), and the
entry is erased. Erase function assumed that every item should be
present in cache, but it is not the case for the entries which are
just parts of item’s payload. This change allows for the item to be
not found in the hashlist, if the CRC32 check fails.
Currently for checking IDF version and submodules existence,
build system uses `git` commands. But, it could be possible use-case
where `git` is not installed (assuming IDF is flattened in source format)
on system and build happens without any warnings.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
Current page selection algorithm selects a page for compaction based on just erased counts
and gives up when it does not find any page with erased count greater than 0. This is
problematic since the current allocation procedure skips the active page if there is not
enough room for the item in that page leaving free chunks on the pages. This change modifies
the algorithm to consider both erased as well as free counts on the candidate pages.
Closes TW<20297>
Users needs functions to count the number of free and used entries.
1. `nvs_get_stats()` This function return structure of statistic about the uspace NVS.
(Struct: used_entries, free_entries, total_entries and namespace_count)
2. `nvs_get_used_entry_count()` The second function return amount of entries in the namespace (by handler)
3. Added unit tests.
Closes TW<12282>
1. fix a bug in initliazing map beacon interval.
2. fix not send MESH_EVENT_ROUTING_TABLE_REMOVE when MESH_NWK_CHILD_DISCONNECTED.
3. fix a bug in returning roots ie len.
Since !2190, source files located outside of the component root
produce object files inside build directory. This change fixes
handling of COMPONENT_OBJEXCLUDE variable for such files. Tests are
added.
- In SPI mode, the card will respond to the initial SDIO reset (done
using CMD52) with “invalid command” error. Handle this correctly.
- sdmmc_card_init had a hack where GO_IDLE_STATE (CMD0) command was
sent twice. Add explanation why this is done, and don’t expect
correct response from the card on first CMD0.
- improve logs printed at debug level by adding CMD index
- Split SDMMC page into pages about SDMMC/SDSPI hosts and a page about
the protocol layer.
- Use autogenerated API reference instead of manually generated one.
- Add information about SDIO APIs.
- Add SDIO support at protocol layer (probing, data transfer, interrupts)
- Add SDIO interrupts support in SDMMC host
- Add test (communicate with ESP32 in SDIO download mode)
Existing code assumed that response timeout is not followed by CMD_DONE,
which was not true, in fact. Host datasheet states that CMD_DONE is sent
after an RTO.
All the commands which do not have a response must have their flags set
accordingly. Therefore the host will not send RTO interrupt if response
is not expected. It is a bug in the code logic if it happens otherwise.
SDMMC host suffers from an issue that it outputs data near the rising
edge of the card clock, which is the edge used by the card to sample
data. If sampling time constraint is not satisfied, card may read data
after the transition.
The phases of output/input data can, in fact, be adjusted. However this
adjustment happens in the clock generation block outside of the host.
So the maximum phase change which can be created this way is equal to
half of the host clock period. So if the host clock is set to the lowest
possible frequency (for the given card frequency), then the phase offset
(and hence the hold time) will be the highest. This change modifies the
logic used to determine clock dividers accordingly.
sdmmc host: set correct dout phase and print correct frequency
SET_BUS_WIDTH is not a data transfer command. Extensive search in the
host datasheet and SD card spec did not reveal the origin of this hack
or 'feature'. Further testing showed that removing this does not lead to
regressions.
Fixes exceptions LoadProhibited, when rmt tries read variable p_rmt on RX END which can be 0.
It happens after esp_reset() (OTA) and the rmt is not probably stopped by it.
In other words the routine rmt_driver_isr_default was called before second rx channel was registered.
scenario:
register tx channel
register rx channel
reboot
register tx channel
-> exception (because rx channel is accessed)
Merges https://github.com/espressif/esp-idf/pull/1671
- In some cases where the HTTP URL contains the port number
(http://hostname:334), the DNS querier fails to resolve the hostname.
- Hence we have to populate the port number ourselves.
- This can only be done based on whether we get an IPv4 or IPv6
address.
Purpose:
1. TLS calls can be too many, and require a user to know the expected behaviour. A simple TLS socket wrapper that can be used in any higher level protocol.
2. Uses OpenSSL compatibility layer, so applications using esp-tls can be built on the host, and it should just work on ESP
Strips leading ../ when generating object file paths, keeps these in sync with the source files
otherwise.
This prevents object files landing in other directories, including outside the build directory, if
the component_srcdirs start with ../
When splitting a memory block, check if the next block is free.
If it is, then just extend it upwards instead of creating a new block.
This fixes a bug where when shrinking existing allocations would result in irreversible free space fragmentation.
When testing on the host, test all the poisoning configurations.
SDSPI driver optimized polling of the response tokens by requesting
two extra bytes on top of the block size (512) and CRC (2), and
checking whether these bytes contained the data response token or
not. In case the token was there, further polling would not need to
happen, thereby reducing latency between two consecutive blocks
transferred. However this caused compatibility issues when these two
extra bytes were sent after reading the final block. When
STOP_TRANSMISSION command was sent, these extra two bytes were
treated as part of the command, causing an invalid command error.
This fixes the logic by only requesting extra two bytes if the block
being read is not the final block. In addition to that, more strict
error checking is implemented for command response tokens.
The files updated according to code review discussions.
In the sleep_modes.c removed immidiate disable of ULP mode and leave just trigger deactivation.
The esp_sleep.h is updated to have the same defines for source as esp_sleep_wakeup_cause_t.
Updated documentation in sleep_modes.rst file to include cross references and address esp_sleep_wakeup_cause_t type.
The get_time_ms() is updated to explicitly use fabs(dt) instead of abs(dt) in test_sleep.c.
Some other minor changes in test_sleep.c unit test.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
Some application lock interrupt(portENTER_CRITICAL) too long time,
it will cause bluetooth cannot react interrupt in time, then t will
cause some assert, assert info following:
1. ld_acl.c 1900
2. ld_fm.c 340
3. other assert reference to this.
We had some problems:
simultaneous compiling of kconfig in the same tree;
attempt to use menuconfig in some examples and ut in batch mode (w/o interactive console)
Also increase debug abilities in CI:
force non-interactive building;
add variable DEBUG_SHELL to toggle verbosity of scripts
It is not possible to generate 1 MHz REF_TICK from 2 MHz APB clock
(this is a limitation of REF_TICK divider circuit). Since switching
REF_TICK frequency is something we would like to avoid (to maintain
UART output even with DFS), 2 MHz frequency has been marked as
unsupported.
The issue would manifest itself in cases when switching from PM
configuration like {active=160MHz, idle=80MHz} to {active=80MHz,
idle=80Mhz}. After the configuration was changed, PM logic would
think that current frequency was 80MHz and would not do any further
switching. In fact, frequency was still 160MHz.
The old code calculated MAX() of two enum values, but CPU frequency
enum values are not ordered (2MHz goes after 240MHz). This caused
incorrect configuration to be set.
Previous code contained a check for PLL frequency to be 240MHz, while
in fact 240MHz was a CPU frequency; corresponding PLL frequency is
480MHz. Fixed the comparison and replaced integer MHz values with an
enum.
This commit adds character encoding configurations in for the fatfs component.
The FF_LFN_UNICODE definition in ffconf.h can now be changed to accept UTF-8 or
UTF-16 encoded filernames. Test cases using UTF-8 encoded file paths and names in
FatFs have also been added.
Closes#1183
1. External 32kHz crystal is started for too long or it may not start at all. It is often observed at the first start.
2. At the first start, it is possible that the crystal did not start. And the recorded period was recorded as 0. Which led to a division error by zero during the transition to the deep sleep mode (Maybe somewhere else).
3. Added a unit test to test a new method of oscillation an external crystal.
4. Added a new method of oscillating of an external crystal. The legs of the crystal are fed with a 32 kHz frequency.
The new method eliminates these errors.
Added unit test: `\esp-idf\components\soc\esp32\test\test_rtc_clk.c`: `make TEST_COMPONENTS=soc`
- 8 Test starting external RTC crystal. Will pass.
`Bootstrap cycles for external 32kHz crystal` - is specified in the file Kconfig by default 100.
QA tested a new method of oscillation the crystal on 25 boards. The supply of square waves on the crystal showed a 100% result in contrast to the previous method of launching the crystal. After the tests, the old method was deleted.
Closes TW19143
The expected usage is:
esp_pthread_set_cfg(cfg);
pthread_create()
If the inherit flag is set, then all subsequent threads forked by this
thread will also inherit this configuration. This avoids having to
change/prefix this for each and every pthread_create() call.
Component/bt: fix reconnect fail in smp for v3.0
See merge request idf/esp-idf!2075
(cherry picked from commit 7f2a9f0359)
d0e55335 Component/bt: fix reconnect fail in smp
The fast path of CPU frequency switch function, used in DFS, was not
waiting for the frequency switch to complete when switching from XTAL
to PLL. This resulted in incorrect reads from peripherals on APB,
where two consecutive reads could return the same value. For example,
in esp_timer, read of FRC_COUNT_REG would return same value as the
preceding read of FRC_ALARM_REG, causing time to jump by the value of
FRC_ALARM_REG / apb_freq_mhz.
- separate mode stats from lock stats by an extra comment line
- add CPU frequency column to the mode stats
- don’t print a row for light sleep if light sleep is not enabled
s_cpu_freq_by_mode array was statically initialised with 80MHz CPU
frequency in CPU_MAX and APB_MAX modes, but sdkconfig setting for the
CPU frequency could have been different. For the case of 240MHz CPU
frequency, this would cause a frequency switch between 240MHz and
80MHz to happen, even though such switch is not supported in the fast
path switching functions used by the DFS implementation.
This fixes the issue by moving initialisation into esp_pm_impl_init,
which is called at startup before the first mode switch can happen.
Fixes https://github.com/espressif/esp-idf/issues/1729.
The files updated according to code review discussions.
In the sleep_modes.c removed immidiate disable of ULP mode and leave just trigger deactivation.
The esp_sleep.h is updated to have the same defines for source as esp_sleep_wakeup_cause_t.
Updated documentation in sleep_modes.rst file to include cross references and address esp_sleep_wakeup_cause_t type.
Some minor changes in test_sleep.c unit test.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
The files updated according to code review discussions.
In the sleep_modes.c removed immidiate disable of ULP mode and leave just trigger deactivation.
The esp_sleep.h is updated to have the same defines for source as esp_sleep_wakeup_cause_t.
Updated documentation in sleep_modes.rst file to include cross references.
Some minor changes in test_sleep.c unit test.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
On most microcontrollers I have worked with one can retrieve the
current state of output GPIO pins. On ESP32 this is not the case
if the pad is not explictly configured to route this information into
the port by configuring it as input or i/o.
Thus add a warning to the API documentation of gpio_get_level().
Merges https://github.com/espressif/esp-idf/pull/1740
Added function esp_sleep_disable_wakeup_source() to deactivate wakeup trigger for selected source.
Updated documentation for this function in sleep_modes.rst file.
Updated unit test to check this functionality for light sleep.
The test_sleep.c unit test is updated to add reliability for unit testing.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
The timer wakeup function once activated cannot be disabled later using existing api. If user wants to use different wakeup sources after first sleep but it does not work. This change disables timer wakeup trigger in configuration that will be set into appropriate RTC registers in esp_light_sleep_start() function.
Added function esp_sleep_disable_wakeup_source() to deactivate wakeup trigger for selected source.
Updated documentation for this function in sleep_modes.rst file to pass make html.
Updated unit test to check this functionality for light sleep.
The test_sleep.c unit test is updated to add reliability for auto unit testing.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
This commit fixes an incorrect register definition for BLK3_RESERVED_FLAG.
Other bugs include a missing conditional check, and updated comments
on modifying eFuse checking behavior.
On each documentation build (‘make html’), doxygen regenerates XML
files. In addition to that, gen-dxd.py regenerates API reference
files under _build/inc/. This results in Sphinx flagging about half
of the input files as modified, and incremental builds taking long
time.
With this change, XML files generated by Doxygen are copied into
docs/xml_in directory only when they are changed. Breathe is pointed
to docs/xml_in directory instead of docs/xml. In addition to that,
gen-dxd.py is modified to only write to the output file when contents
change.
Overall, incremental build time (with no source files changed) is
reduced from ~7 minutes to ~8 seconds (on a particular OS X
computer).
Due to the way Breathe includes Doxygen XML files, there is still
going to be a massive rebuild every time functions, enums, macros,
structures are added or removed from the header files scanned
by Doxygen, but at least individual .rst files can be edited
at a much faster pace.
This commit adds support for CPU max freqeuency rating
bits in CPU. Bootloader will now print an error if attempting
to 160MHz rated ESP32 at 240MHz.
EFUSE_CHIP_VER_RESERVE has been replaced by the
frequency rating bits. Dependancies on EFUSE_CHIP_VER_RESERVE
have been changed to use EFUSE_CHIP_VER_PKG
This commit removes the lookup table mode due to inferior performance when compared
to linear mode under attenuation 0, 1 and 2. However small portions of the lookup table
are kept for the higher voltages of atten 3 (above ADC reading 2880). That voltage range
in atten 3 has non linear characteristics making the LUT performan better than linear mode.
Add back a feature that was available in the old heap implementation
in release/v2.1 and earlier: keep track of which task allocates each
block from the heap. The task handle is conditionally added as
another word in the heap poisoning header under this configuration
option CONFIG_HEAP_TASK_TRACKING.
To allow custom monitoring and debugging code to be added, add helper
functions in multi_heap.c and multi_heap_poisoning.c to provide access
to information in the block headers.
Add esp_heap_debug_dump_totals() to monitor heap usage
esp_heap_debug_dump_totals() dumps into a user-provided data structure
a summary of the amound of heap memory in region type that is used by
each task. Optionally it will also dump into another data structure
the metadata about each allocated block for a given list of tasks or
for all tasks (limited by available space).
Address change requests on PR #1498
This set of changes fixes the files in e3b702c to just add the
CONFIG_HEAP_TASK_TRACKING option without adding the new function
heap_caps_get_per_task_info() in case that is the only portion of the
PR that will be accepted. Part of the change is to remove the new .c
and .h files containing that function and to remove the line to
compile it from components/heap/component.mk since it should not have
been included in e3b702c. One or more additional commits to add the
new function will follow.
The other changes here:
- uint32_t get_all_caps() moves to heap_private.h
- replace "void* foo" with "void *foo"
- add braces around single-line "if" blocks
- replace tab characters with spaces
Address change requests on PR #1498, part 2
This set of changes fixes the files in cdf32aa to add the new function
heap_caps_get_per_task_info() with its new name and to add the line to
compile it in components/heap/component.mk. This does not address all
the suggested changes because there are some needing further
discussion.
This commit does not include the suggested change to move the
declaration of the new function into esp_heap_caps.h because the new
function references TaskHandle_t so esp_heap_caps.h would have to
include freertos/FreeRTOS.h and freertos/task.h, but FreeRTOS.h
includes esp_heap_caps.h through two other header files which results
in compilation errors because not all of FreeRTOS.h has been read yet.
Change heap_caps_get_per_task_info() to take struct of params
In addition to moving the large number of function parameters into a
struct as the single parameter, the following changes were made:
- Clear out the totals for any prepopulated tasks so the app code
doesn't have to do it.
- Rather than partitioning the per-task totals into a predetermined
set of heap capabilities, take a list of <caps,mask> pairs to
compare the caps to the heap capabilities as masked. This lets the
caller configure the desired partitioning, or none.
- Allow the totals array pointer or the blocks array pointer to be
NULL to indicate not to collect that part of the information.
- In addition to returning the total space allocated by each task,
return the number of blocks allocated by each task.
- Don't need to return the heap capabilities as part of the details
for each block since the heap region (and therefore its
capabilities) can be determined from the block address.
- Renamed heap_task_info.h to esp_heap_task_info.h to fit the naming
convention, and renamed the structs for totals and block details to
better fit the revised function name.
- Provide full Doxygen commenting for the function and parameter
structs.
Add copyright header to new files
Merges https://github.com/espressif/esp-idf/pull/1498
Chapter Flash from Eclipse: Changed "Select Make Targets -> ..." to "Select Build Targets -> ..." to match the Eclipse wording. Same with "Project -> Make Target" replace Make by build to match the Eclipse wording.
tools/gen_esp_err_to_name.py generates
components/esp32/esp_err_to_name.c for lookup of the error codes from
all of the IDF project and easily identify all codes in one place
This commit updates the esp_adc_cal ocmponent to support new calibration methods
which utilize calibratoin values stored in eFuse. This commit includes LUT mode
At debug log level, tcpip_adapter would print logs for each function
call scheduled onto the tcpip task. These logs contained pointers which
idf_monitor decoded, adding even more noise and useless vertical space
in logs. This change moves these log statements to verbose level.
When realloc-ing to a smaller buffer size which ends up allocated in a different heap, the heap
structure is corrupted. This can only happen:
* If heap checking is Comprehensive (meaning buffers are never shrunk in place) and the heap the buffer was originally allocated in is full.
* Calling heap_caps_realloc() to deliberately move a buffer to a different capabilities type, and shrink it at the same time.
Probable fix for https://github.com/espressif/esp-idf/issues/1582
Probably the same issue:
https://www.esp32.com/viewtopic.php?f=2&t=4583https://www.esp32.com/viewtopic.php?f=13&t=3717
use performance matrix to tracking bin size is not convenient. bin size
do change for a lot reasons.
we'll implement a new method to track it. before that, set a large
enough threshold, so we can still keep tracking it.
The TRM describes IOMUX registers are IO_MUX_x_REG for x in GPIO0-39.
Until now ESP-IDF describes them as PERIPHS_IO_MUX_(pinname)_U
This commit adds additional IOMUX register names which match the ones used in the TRM.
1. Put some lwip udp rx/tx relating functions to IRAM
2. Put some wifi rx/tx relating functions to IRAMa
3. Reduce wifi dynamic malloc from 4 to 1 for each ebuf
4. Update iperf example accordingly
5. Update libphy.a to v383
Reported from github: https://github.com/espressif/esp-idf/issues/1236
All the touch channels are enabled by default in hardware. This would interfere other RTC function on Touch IOs.
Disable touch function in touch_pad_init().
function is called but NOT withe the same 'c' string constant that the LOG*
calls used in each module, the cache check doesn't match, so the cached
entry won't get updated. There's no point in optimizing this function
anyway because it is only called rarely.
Fix `#if (LOG_LOCAL_LEVEL >= ESP_LOG_INFO)` which is always false and
produces a warning with -Wundef.
Use same pattern to compare LOG_LOCAL_LEVEL with ESP_LOG_INFO as is used
in definition of `ESP_LOG_BUFFER_HEX_LEVEL` and
`ESP_LOG_BUFFER_CHAR_LEVEL`.
Also reformat existing definitions for better readability.
Closes https://github.com/espressif/esp-idf/issues/1526
Bluedroid use a set of timer function pairs such as btu_start_timer/btu_stop_timer, btu_sys_start_timer/btu_sys_stop_timer for use, in a lack of timer release functions. Thus the timers may be exhausted after some event sequence such as repetition of connection/reconnection with different devices. The maximum timer number used in bluedroid is given by ALARM_CBS_NUM which is 30 for now. This bugfix borrowed some update from bluedroid in Andoroid 7.0, which add timer release functions which promote the recycle of timer resources.
close github issue#1037 WiFi Promiscuous filter breaks w/
WIFI_PROMIS_FILTER_MASK_ALL and issue#1404
esp_wifi_set_promiscuous_filter set WIFI_PROMIS_FILTER_MASK_ALL error
component/bt: Added the Macro for the classic BT support.
component/bt: added the bluedroid deinit method.
component/bt: allow more classic BT global variables to use dynamic allocation scheme
1. allocate memory for AVDT, AVCT control blocks when dynamic memory is used
2. allow SBC decoder buffer to use dynamic allocation scheme
component/bt: Remove the wrong changes in bt/Kconfig & Added the GATTS_INCLUDED in the gatt_free function when gatt service close.
component/bt: Shorten the abbreviation BT_ALLOCATION_FROM_SPIRAM_FIRST and BT_BLE_DYNAMIC_ENV_MEMORY two macros.
requirement from github(https://github.com/espressif/esp-idf/issues/805): to provide the position in the buffer of the pattern detected.
requirement from AT application: in AT app, when no hardware flow control is enabled, in some situation the rx buffer might be full, and the terminator “+++” might be lost, we can use pattern detect interrupt to avoid missing the terminator. When pattern detect interrupt happens, it will not send a data event at the same time.
1. Add API to get position of detected pattern in rx buffer
2. Modify UART event example
3. Add comments for uart_flush, add alias API uart_flush_input to clear the rx buffer
4. Modify the way rx_buffered_len is calculated
Changes related to DFS have broken compilation of sysview code in 1 core
mode. This change fixes this, and moves choice of the timer used for
timestamp into Kconfig. CCOUNT timer is only available as an option if
1 core mode is used. esp_timer is added as a new option, and is the
only available option if DFS is enabled.
1. "lwip_socket" should close by "lwip_close_r" other than "lwip_close"
2. for generally compatible, fix all lwip interface to normally socket interface
3. call vTaskDelete when new socket failed in case of task crash
close #https://github.com/espressif/esp32-at/issues/58
1. remove the feature mask parameter from AVRC connection state event, as the AVCTP connection can be initiated by remote device before service discovery to remote device is performed. \
In this case, AVRCP connection state event may not be reported after connection initated by remote device is established.
2. remove ESP_AVRC_CT_MAX_EVT
3. add more documentations to AVRC APIs
When INT WDT fires, panicHandler is invoked. In OCD mode, panicHandler
sets a breakpoint on the PC from the exception frame and returns.
However in case of INT WDT, interrupt flag is still set in TIMERG1
peripheral, which causes INT WDT to trigger again. This causes an
endless stream of "Core 0 panic'ed (Interrupt wdt timeout on CPU1)"
messages. OpenOCD also gets terribly confused at this point.
Disable watchdogs when exiting panic handler in OCD mode.
Clear TIMERG1 WDT interrupt flag to prevent re-entry into panic handler.
RTC_FAST_CLK_FREQ_APPROX is defined as 8500000, so 0.5MHz part was lost
when dividing by MHZ. Since cal_val is 64-bit the parens can be removed.
With 40MHz XTAL for a nominal ESP32 chip, this fixes estimated XTAL
frequency from 38 to 40MHz.
In order for the Eclipse CDT GCC Build Output Parser to be able to
pick up the include paths for C++/cpp files a space is required
between the compiler option (-I) and the actual path.
Merges https://github.com/espressif/esp-idf/pull/1474
LOG_LOCAL_LEVEL is now used in a construct like:
#if (LOG_LOCAL_LEVEL >= ESP_LOG_INFO)
Make sure that LOG_LOCAL_LEVEL is defined, and don't use a type cast in
its definition, because preprocessor can not parse that.
1. ESP32 is found to suffer from AES encryption start/resume failure with specific device. Therefore temporarily disable BR/EDR Secure Connections for a workaround
2. BR/EDR Secure Connections is a feature for BT Classic introduced in Bluetooth 4.1. This change disables the setting of Secure Connections(Host Supported), and will result in the use of legacy authentication instead of secure authentication, and E0 encryption(legacy) instead of AES-CCM encryption. BLE security procedures are not affected.
Bugfix to prevent a self deleting no affinity task's memory from being freed by the
idle task of the other core before the self deleting no affinity task is able to context
switch out. prvCheckTasksWaitingTermination now checks if the task is still on
pxCurrentTCB before freeing task memory.
When tcp write/connect is running, close socket request will abort
it and continue to delete netconn and close tcp. Do not immediately
return after aborting tcp write/connect. Otherwise, tcp close
requeset will block and tcp write/connect will crash.
1. optimiz the ble stop adv callback function.
2. added the osi_mutex_unlock in the bta_gattc_wait4_service_change_ccc_cback function when the p_timer_param == NULL || p_conn == NULL.
1. fix the bug. Modify the condition that esp_bt_controller_mem_release() shoud be only called before esp_bt_controller_init() or after esp_bt_controller_deinit()
2. modify the example to use esp_bt_controller_mem_release()
libc time function now rely on esp_timer_get_time as the source of
high-resolution time, rather than FRC1 timer. Internally, on the ESP32
esp_timer implementation uses FRC2 timer.
- Change help text and labels in Kconfig to use "high-resolution timer"
instead of FRC1. Keep existing Kconfig option name to be backwards
compatible.
- Change references to "FRC1" in the source code to "FRC".
Replace explicit masks and shifts with bit fields when working with FATFS date and time representations. Also zero-initialize remaining members of struct tm.
Fixes https://github.com/espressif/esp-idf/issues/1369.
A couple of typos referencing tx_ring_buf when rx_ring_buf, slv_tx_mux
instead of slv_rx_mux.
Also, I2C_ENTER_CRITICAL()/I2C_EXIT_CRITICAL() usage was not consistent.
Only some of the _set_ functions had them. Most of the _get_ function
had them? It is my understanding that they should be wrapped around
writes, not reads? (I think we still need the lock for reading pairs of consistent values)
Also, the ticks_to_wait timeout handling in i2c_master_cmd_begin() would
not handle integer rollover correctly.
Merges https://github.com/espressif/esp-idf/pull/1180
Previously SDSPI host driver would rely on retry count when waiting for
the card to read or write data. This caused different timeout times
depending on CPU frequency and card clock frequency. In practice, card
performance does not depend on these two factors.
This change uses timeout_ms field of sdmmc_command_t introduced
previously for SDMMC host.
Fixes https://esp32.com/viewtopic.php?f=2&t=3440&p=16037 and similar
issues related to SDSPI timeouts.
FATFS does not support f_stat call for drive root. When handling stat
for drive root, don't call f_stat and just return struct st with S_IFDIR
flag set.
Closes#984
A function to change "in IRAM" status for an existing interrupt handle, without going through free/allocate of the interrupt.
mOS HW timer implementation requires this to make HW timers safe to re-set from an IRAM ISR.
This is a wrapper API for creating a Ring Buffer, which ensures that
the ringbuffer can hold the given number of items, each item being of the
same given length.
Signed-off-by: Piyush Shah <piyush@espressif.com>
Useful to check if the next item to receive is wrapped or not.
This is valid only if the ring buffer is initialised with type
RINGBUF_TYPE_ALLOWSPLIT.
This is as per the feature request here:
https://github.com/espressif/esp-idf/issues/806
Signed-off-by: Piyush Shah <piyush@espressif.com>
The earlier available API (xRingbufferGetMaxItemSize())just gives
a static max entry value possible for given ring buffer.
There was a feature request for an API which could provide
a real time available buffer size. See below:
https://github.com/espressif/esp-idf/issues/806
Signed-off-by: Piyush Shah <piyush@espressif.com>
current unit-test-app don't support test components need to communicate
with each other (like GPIO, SPI ...). Now we add multiple devices mode
to unit test app, support writing and running test with multiple DUTs.
please refer to `docs/api-guides/unit-tests.rst` for detail.
- Use `code` tags instead of a mix of `<pre></pre>` and
`@verbatim .. @endverbatim`
- Remove manually added function prototypes from comment blocks
- Remove of grouping (`\defgroup`) — some extra work is needed
to make groups compatible with the way we auto-generate API
reference from Doxygen XML files. It's pretty easy to add the
grouping directives back if/when we implement support for
Doxygen groups in the later stages of documentation build
process.
- Hide private APIs under `@cond .. @endcond`
- Convert some comments into Doxygen-compatible ones
- Fix various documentation issues: missing documentation for
some parameters, mismatch between parameter names in comment
block and in function prototype.
- Add doxygen comments for functions which didn't have them
(thread local storage).
- Add [out] param tags where necessary
- Redefine `xTaskCreate` and `xTaskCreateStatic` as inline
functions instead of macros.
When compiling
> const ulp_insn_t program[] = {
> I_DELAY(1)
> };
with the xtensa-esp32-elf-g++ compiler i always got the error:
> sorry, unimplemented: non-trivial designated initializers not supported
>
> };
This was due to the different order in the macro and the struct. The struct has another order of the fields (opcode, unused, cycles) vs (cycles, unused, opcode):
> struct {
> uint32_t cycles : 16; /*!< Number of cycles to sleep */
> uint32_t unused : 12; /*!< Unused */
> uint32_t opcode : 4; /*!< Opcode (OPCODE_DELAY) */
> } delay; /*!< Format of DELAY instruction */
After updating the order in the macro it is possible to compile with the g++ compiler.
Merges https://github.com/espressif/esp-idf/pull/1310
This commit backports vTaskDelete() behavior from FreeRTOS v9.0.0 which
allows for the immediate freeing of task memory if the task being deleted
is not currently running and not pinned to the other core. This commit also
fixes a bug in prvCheckTasksWaitingTermination which prevented the
Idle Task from cleaning up all tasks awaiting deletion. Each iteration of the Idle
Task should traverse the xTasksWaitingTermination list and clean up all tasks
not pinned to the other core. The previous implementation would cause
prvCheckTasksWaitingTermination to return when encountering a task
pinned to the other core whilst traversing the xTasksWaitingTermination list.
The test case for vTaskDelete() has been updated to test for the bugfix and
backported deletion behavior.
* Change snprintf for strlcat does not complain w/gcc7.2.0 and it is safer, thanks @projectgus
* Use proper quotes for character literals
Merges https://github.com/espressif/esp-idf/pull/1163
1. Add a hide API for station to receive and process probe request
frame.
2. Fix an issue that wifi/bt coexistence crashes in PSRAM version.
3. Fix an issue that the API for clearing vendor ie can not work.
4. Fix an issue that wifi stop and reboot leads watchdog.
Reported from github:
https://github.com/espressif/esp-idf/issues/1312https://github.com/espressif/esp-idf/issues/1193
Issues:
1. We used to use event group in the driver, which would cause:
a. longer operation time since the event group are based on FreeRTOS timer.
b. Operation fails if the timer queue is not long enough.
2. There might be some issue with event group, we will still try to provide a small test code in other branch.
modification:
1. use queue instead of event-bit for internal commands
2. use queue overwrite for cmd_done event
Timer callback can delete the timer. If CONFIG_ESP_TIMER_PROFILING was
enabled, this caused an access to invalid (freed) memory.
This fix adds a pointer to track the timer while executing the callback.
This is needed so that we can check if callback deletes the timer,
in which case we won't try updating profiling counters for this timer
after the callback is done.
This commit backports the following features from FreeRTOS v9.0.0
- uxSemaphoreGetCount()
- vTimerSetTimerId(), xTimerGetPeriod(), xTimerGetExpiryTime()
- xTimerCreateStatic()
- xEventGroupCreateStatic()
- uxSemaphoreGetCount()
Functions backported previously
- xTaskCreateStatic()
- xQueueCreateStatic()
- xSemaphoreCreateBinaryStatic(), xSemaphoreCreateCountingStatic()
- xSemaphoreCreateMutexStatic(), xSemaphoreCreateRecursiveMutexStatic()
- pcQueueGetName()
- vTaskSetThreadLocalStoragePointer()
- pvTaskGetThreadLocalStoragePointer()
Unit tests were also written for the functions above (except for pcQueueGetName
which is tested in a separate Queue Registry MR). The original tlsp and del cb test case
was deleted and integrated into the test cases of this MR.
When using CPP and C combination this particular file threw error on linking.
Merges https://github.com/espressif/esp-idf/pull/1249
(Amended to add INC_FREERTOS_H guard, comment on #endif)
1. Usage of this module required applications to include additional
files. What files to include is not very intuitive. Instead, it is
better for the header file itself to include other files as required.
2. Even though it may seem logical, it is better to explicitly mention
that an item needs to be "Returned" after a Receive
Signed-off-by: Piyush Shah <piyush@espressif.com>
It was observed that if the ring buffer size provided by application
is not a multiple of 4, some checks were failing (as read_ptr and write_ptr
could shoot beyond the ring buffer boundary), thereby causing asserts.
Simply wrapping around the pointers for such cases fixes the issue.
Moreover, because of the logic for maintaining 4-byte boundary,
it was also possible that a wrap-around occurred for some data,
even when the actual size remaining was sufficient for it.
Eg. Buffer available: 34, data size: 34, 4-byte aligned size: 36
Since the logic compares against 36, it writes 34 bytes and does a
wraparound. But since all 34 bytes are already written, there is
nothing to write after wrapping. It is better to just re-set the
write pointer to the dtart of ring buffer in such cases.
Tested send/receive for various arbitrary sizes of data and for
arbitrary sizes of ring buffer.
Alternative Solutions:
1) Allow only sizes which are multiples of 4, and return error otherwise.
Appropriate code and documentation change would be required
2) Allow arbitrary sizes, but internally add upto 3 bytes to make
the total size a multiple of 4
Signed-off-by: Piyush Shah <piyush@espressif.com>
disabled
The misssing stubs get pulled in from the toolchain's libstdc++ also
causing to pull in defined stubs. This results in redefinition of
symbols. Fixing it by simply adding the missing stubs when exceptions
are disabled.
Signed-off-by: Amey Inamdar <amey.inamdar@gmail.com>
This defines the OpenSSL X509_CHECK_FLAG_...s and the set/clear
accessors. Since none of them are supported, the set / clear
accessor currently always does nothing and returns error.
This call is often part of the generic openssl user code to
set up certificate verification. This patch allows it to
compile for ESP32 and decide at runtime what to do about
unsupported flags.
Merges https://github.com/espressif/esp-idf/pull/980
This lets the user code set the mbedtls hostname using the standard OpenSSL
X509_VERIFY_PARAM_set1_host() API semantics.
The API takes an X509_VERIFY_PARAM pointer. We use the fact that is
a composed member of the SSL struct to derive the SSL pointer.
The X509_VERIFY_PARAM_set1_host() is unusual in that it can accept a
NUL terminated C string as usual, or a nonterminated pointer + length.
This implementation converts the latter to the former if given, before
using it.
This is enough for user code to get the openssl wrapper to make
mbedtls confirm the CN on the peer cert belongs to the hostname used
to reach it, by doing, eg
X509_VERIFY_PARAM_set1_host(SSL_get0_param(myssl), myhostname, 0);
Merges https://github.com/espressif/esp-idf/pull/980
This adds the standard OpenSSL api to get a pointer to the SSL struct's
X509_VERIFY_PARAM. We need this for the OpenSSL api to set the peer
hostname introduced in the next patch.
Part of https://github.com/espressif/esp-idf/pull/980
These functions were discarded but not provided in ROM.
Generated from commit 8ad0aa7d6 in newlib script repo. Didn't rebuild most of libc/libc_nano,
only appended the missing object files to the existing archives (should save some git churn).
Rephrased the example's description to make it easier to understand
and made other grammatical fixes.
Signed-off-by: Piyush Shah <piyush@espressif.com>
- Trailing white spaces removed
- Re-formatted switch-case
Basic indentation fixes were done using tools/format.sh and switch-case
formatting was done manually (to identify different levels for "switch"
and "case")
Signed-off-by: Piyush Shah <piyush@espressif.com>
In the queue registry test, start_sem is given twice to let both tasks
start the test. Each task takes start_sem, does some work, gives done_sem,
and goes on to wait for start_sem again.
It may happen that one task can grab start_sem, add queues to the
registry, give done_sem, then grab start_sem again, delete the queues
from the registry, and give done_sem again. At this point, main test
task takes done_sem twice and proceeds to verify that queues have been
added to the registry. But in fact, the first task has already deleted
its queues from the registry, and the second one might not have added
the queues yet. This causes test to fail.
This changes the test to use separate start semaphores for each task,
to avoid the race condition.
1. All the registers of touch sensor 8 and 9 are mismatched except the ‘dac’ field in touch register of RTC IO
2. To swap the index for sensor 8 and 9 in APIs.
This commit makes the configQUEUE_REGISTRY_SIZE and
configGENERATE_RUN_TIME_STATS configurable in menuconfig.
- configQUEUE_REGISTRY_SIZE can now be set in menuconfig.
- The functions vQueueAddToRegistry() and vQueueUnregisterQueue() were made
SMP compatbile
- pcQueueGetName() was backported from FreeRTOS v9.0.0
- Added test case for Queue Registry functions
- configGENERATE_RUN_TIME_STATS can now be enabled in menuconfig. CCOUNT or
esp_timer can be selected as the FreeRTOS run time clock in menuconfig as
well, although CCOUNT will overflow quickly.
- Run time stats collection (in vTaskSwitchContext) and generation (in
uxTaskGetSystemState) have been made SMP compatible. Therefore
vTaskGetRunTimeStats() now displays the run time usage of each task as a
percentage of total runtime of both CPUs
Squash
- Remove ASCII-only configuration, CP437 is used instead
- Add dynamic code page configuration
See components/fatfs/src/00history.txt for FATFS changelog.
Reported from github:
https://github.com/espressif/esp-idf/issues/1219https://github.com/espressif/esp-idf/issues/1202
After providing a simple code to digital team, they confirmed that this is a hardware bug.
Root cause:
The fifo reset signal is incorrectly connected
If we want to reset tx fifo of UART2, we have to set txfifo_rst bit of both UART1 and UART2
If we want to reset rx fifo of UART2, we have to set rxfifo_rst bit of both UART1 and UART2
Workaround:
we don't use fifo rst bit in driver.
Documentation:
Digital team would update TRM and give more explanation about this issue.
1. use esp_timer instead of FreeRTOS timer to implement osi_alarm in bluedroid
2. Remove two APIs: osi_alarm_now() and osi_alarm_time_diff() and modify the hci layer logic that use them
3. Implement osi_alarm_get_remaining_ms()
4. Move the definition of struct alarm_t in source file "alarm.c"
5. Add definition of module error code
To achieve reliable operation with GD flash at 80MHz, need to raise
core voltage.
This causes the following current consumption increase:
At 80MHz: from 29mA to 33mA
At 160MHz: from 41mA to 47mA
Test conditions: 2 cores running code from IRAM, remaining peripherals
clock gated.
Earlier recursive mutex was being used for this but since
SCOMPARE1 is already being saved/restored during context
switch, atomic compare and set can be used for this.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
Test cases were added for the following functions
- xTaskNotify(), xTaskNotifyGive(), xTaskNotifyFromISR(), vTaskNotifyGiveFromISR(),
- xTaskNotifyWait(), ulTaskNotifyTake()
- vTaskDelayUntil()
The following function was made smp compatible and tested as well
- eTaskGetState()
Intention is to partition the demo into multiple files, so that the
main program is quite easy to follow.
1. connectlib.c: For any URL parsing and TCP connection related stuff
2. sh2lib.c: Convenience functions for HTTP2+TLS. The goal here is to
expose a simpler API than nghttp2. If most usecases end up being
served with this library, it could potentially be moved into a separate
component
Old behavior assumes message compressed when any of 2 most significant bits are set,
But in fact Message compressed only when both those bits are set to 1.
Also maximal label length should be 63 bytes.
Renamed the internal rc to __err_rc to avoid clashes with local variables.
This code would not do the expected thing with the original ESP_ERROR_CHECK macro:
esp_err_t my_func(esp_err_t x)
{
assert(x == 23);
}
esp_err_t rc = 23; //some value that is important fo the user
ESP_ERROR_CHECK(my_func(rc));
The macro will expand to:
esp_err_t rc = (my_func(rc));
And the code will assert, as my_func will receive a random value - whatever is in the internal macro rc temp variable. This is due to the C weirdness of allowing this code:
int x = x; //x has a random value.
Pointer tcpip_api_call *m should be converted to pppapi_msg* instead of pppapi_msg_msg*
in pppapi_do_ppp_set_default(), pppapi_do_ppp_free() and so on.
It solve this issue https://github.com/espressif/esp-idf/pull/1028
so there is no need to patch ip4.c because now netif_defauilt is setted correctly.
Also it prevents memory corruption when pppapi_free() is called.
This commit reverts the revert on the new task watchdog API. It also
fixes the following bug which caused the reversion.
- sdkconfig TASK_WDT_TIMEOUT_S has been reverted from the unit of ms back to the
unit of seconds. Fixes bug where projects using the new API without rebuilding sdkconfig
would cause the old default value of 5 to be interpreted in ms.
This commit also adds the following features to the task watchdog
- Updated idle hook registration to be compatible with dual core hooks
- Updated dual core hooks to support deregistration for cpu
- Legacy mode has been removed and esp_task_wdt_feed() is now replaced by
esp_task_wdt_reset(). esp_task_wdt_feed() is deprecated
- Idle hooks to reset are now registered/deregistered when the idle tasks are
added/deleted from the Task Watchdog instead of at Task Watchdog init/deinit
- Updated example
1. V366, fix a problem which initialize current can reach 800mA.
2. V365, fix a problem for pll_cap tracking in Coexist (BT & WIFI)
mode. The problem will make Coexist (BT & WIFI) WIFI AP mode TX
Fail in high temperature(>70).
3. V364, fix a bug of BT and Wifi coexist (hung in function of
force_wifi_mode())
component/bt: Fix the bug of master don't send pair request to the slave when the sec_act set to the value of ESP_BLE_SEC_ENCRYPT.
See merge request !1376
1. move settings of WIFI_CLK_EN_REG for bluetooth into controller init/deinit APIs
2. modify the bit mask used in phy_rf init/deinit to use WIFI-BT shared bits
This commit updates various test cases throughout esp-idf such that
the values used for timer divider pass the assertions in the timer component.
Timer divider values must be between 2 to 65536
Previously esp_restart would stall the other CPU before enabling RTC_WDT.
If the other CPU was executing an s32c1i instruction, the lock signal
from CPU to the arbiter would still be held after CPU was stalled. If
the CPU running esp_restart would then try to access the same locked
memory pool, it would be stuck, because lock signal would never be
released.
With this change, esp_restart resets the other CPU before stalling it.
Ideally, we would want to reset the CPU and keep it in reset, but the
hardware doesn't have such feature for PRO_CPU (it is possible to hold
APP_CPU in reset using DPORT register). Given that ROM code will not use
s32c1i in the first few hundred cycles, doing reset and then stall seems
to be safe.
In addition to than, RTC_WDT initialization is moved to the beginning of
the function, to prevent possible lock-up if CPU stalling still has any
issue.
1. Make sure that 8MD256 clock used to estimate XTAL frequency is enabled
before trying to use rtc_clk_cal_ratio.
This fixes "Bogus XTAL frequency: 0 MHz" warnings after software reset.
2. Don't call rtc_clk_xtal_freq_estimate if XTAL frequency is already
known. This reduces startup time after deep sleep or software reset.
3. Compare known XTAL frequency and estimated one before printing a
warning. This fixes "Possibly invalid CONFIG_ESP32_XTAL_FREQ setting
(40MHz). Detected 40 MHz." warnings.
Previous implementation waited for 20us after setting
RTC_CNTL_SOC_CLK_SEL_XTL register, using ets_delay_us, assuming that
the CPU was running at XTAL frequency. In reality, clock switch happened
on the next RTC_SLOW_CLK cycle, and CPU could be running at the previous
frequency (for example, 240 MHz) until then.
ets_delay_us would wait for 20 us * 40 cycles per us = 800 CPU cycles
(assuming 40 MHz XTAL; even less with a 26 MHz XTAL).
But if CPU was running at 240 MHz, 800 cycles would pass in just 3.3us,
while SLOW_CLK cycle could happen as much as 1/150kHz = 6.7us after
RTC_CNTL_SOC_CLK_SEL_XTL was set. So the software would not actually wait
long enough for the clock switch to happen, and would disable the PLL
while CPU was still clocked from PLL, leading to a halt.
This implementation uses rtc_clk_wait_for_slow_cycle() function to wait
until the clock switch, removing the need to wait for a fixed number of
CPU cycles.
Some RTC features are synchronized to RTC_SLOW_CLK, so sometimes
software needs to wait for the next slow clock cycle.
This function implements waiting using Timer Group clock calibration
feature.
append adc support and api
- esp_err_t adc2_config_width(adc_bits_width_t width_bit);
- esp_err_t adc2_config_channel_atten(adc2_channel_t channel, adc_atten_t atten);
- int adc2_get_voltage(adc2_channel_t channel);
The mutex is common across all the threads. It needn't be held across
the init_routine() call as long as the 'once' behaviour is guaranteed
Saw a deadlock case, where init_routine of one thread was waiting for
the completion of init_routine in another thread.
t2: wait for command
t1: pthread_once:
lock once_mux
init_routine:
inform thread t2
wait for signal from t2
t2: received command
pthread_once
lock once_mux (already held by t1)
---- Deadlock ----
Reported from:
https://github.com/espressif/esp-idf/issues/703https://github.com/espressif/esp-idf/issues/917
In uart driver we didn't change the default value of tx idle num, so there would be a delay after tx FIFO is empty.
1. Add API to set tx idle interval before next data transmission. (The UART hardware can add an interval after tx FIFO is empty).
2. Set default tx idle interval to zero.
3. Add hardware disable in uart driver delete function.
1. add sw interrupt cause osi to controller.
2. modify the kconfig to improve the option view.
3. add option of the cpu core which bluedroid run.
4. add option of the cpu core which bluetooth controller run.
Previously ioctl was declared as a macro in lwip/sockets.h.
Disabling LWIP_POSIX_SOCKETS_IO_NAMES removed that declaration.
This adds sys/ioctl.h file and the missing declaration.
Also adds missing includes in vfs.c.
component/bt: The application layer does not allocate memory correctly causing the btc layer pointer to cross the border.
bt/examples: Change the gattc_multi_connect.c incorrect memory apply method.
Reported from different sources from github or bbs:
https://github.com/espressif/esp-idf/issues/680https://github.com/espressif/esp-idf/issues/922
We tested reading several sensor or other I2C slave devices, if the power and SDA/SCL wires are in proper condition, everything works find with reading the slave.
If we remove the power supply for the slave during I2C is reading, or directly connect SDA or SCL to ground, this would cause the I2C FSM get stuck in wrong state, all we can do is the reset the I2C hardware in this case.
After this commit, no matter whether the power supply of I2C slave is removed or SDA / SCL are shorted to ground, the driver can recover from wrong state.
We are not sure whether this the save issue with the reported one yet, but to make the driver more robust.
Further information:
1. For I2C master mode, we have tested different situations, e.g., to short the SDA/SCL directly to GND/VCC, to short the SDA to SCL, to un-plug the slave device, to power off the slave device. Under all of those situations, this version of driver can recover and keep working.
2. Some slave device will die by accident and keep the SDA in low level, in this case, master should send several clock to make the slave release the bus.
3. Slave mode of ESP32 might also get in wrong state that held the SDA low, in this case, master device could send a stop signal to make esp32 slave release the bus.
Modifications:
1. Disable I2C_MASTER_TRAN_COMP interrupt to void extra interrupt.
2. Disable un-used timeout interrupt for slave.
3. Add bus reset if error detected for master mode.
4. Add bus clear if SDA level is low when error detected.
5. Modify the argument type of i2c_set_pin.
6. add API to set timeout value
7. add parameter check for timing APIs
This commit makes configUSE_TRACE_FACILITY and
configUSE_STATS_FORMATTING_FUNCTIONS configurable in kconfig. Test cases fro the
functions enabled by the two configurations above have also been added.
Test cases for the following functions have been added...
- uxTaskGetSystemState()
- uxTaskGetTaskNumber()
- vTaskSetTaskNumber()
- xEventGroupClearBitsFromISR()
- xEventGroupSetBitsFromISR()
- uxEventGroupGetNumber()
- uxQueueGetQueueNumber()
- vQueueSetQueueNumber()
- ucQueueGetQueueType()
Test cases for the following functions were not required...
- prvListTaskWithinSingleList()
- prvWriteNameToBuffer()
- vTaskList()
Internal byte accessible memory starts with Internal ROM 1 at 0x3FF90000.
Region of RTC fast memory starting at 0x3FF80000 is not used in IDF as
it is mapped to PRO CPU only.
During a call to multi_heap_malloc(), if both these conditions were true:
- That heap only has one block large enough for the allocation
(this is always the case if the heap is unfragmented).
- Another allocation is simultaneously occurring in the same heap.
... multi_heap_malloc() could incorrectly return NULL.
This caused IDF heap_caps_malloc() and malloc() to also fail, particularly
often if only one or two heaps had space for the allocation (otherwise
heap_caps_malloc() fails over to the next heap).
1. Fix WiFi timer enable twice issue
2. Fix a softAP compatibility issue
3. Fix ebuf alloc counter issue
4. remove nvs_flash_init() in esp_wifi_init()
5. Fix scan only find few APs after set bssid
6. Fix can not connect to hidden SoftAP
7. Remove group key entry before connecting ot AP
- _FS_TINY: disables per-file caches
- _FS_TIMEOUT: locking timeout for concurrent access
- _FS_LOCK: prevents operations which are not allowed on open files
Also sets _MAX_SS based on sector size configured for wear_levelling.
This reduces memory usage of FATFS if wear_levelling is using 512 byte
sectors.
Moves the ets_timer_arm() / ets_timer_disarm() code paths to RAM
Overhead is 740 bytes of IRAM, 0 bytes DRAM
(For comparison: If all of esp_timer.c is moved to RAM, overhead is 1068 bytes IRAM and 480 bytes DRAM.)
Allows fcntl() implementation in vfs to be used.
Closes https://github.com/espressif/esp-idf/issues/1070
Note this is different to the other libc file-related syscalls, as there is no
reent structure involved.
Some frameworks based on ESP-IDF need to be able to decide whether to
initialize SPI RAM after the application has started. This change splits
out part of esp_spiram_init which manipulate cache MMU into a separate
function. Applications can disable cache, call esp_spiram_init_cache,
re-enable cache, and then call esp_spiram_init.
Disabling and re-enabling the cache can be achieved using functions
provided in esp_spi_flash.h.
This commit fixes bugs with the dual core changes to freeRTOS tick and idle hooks.
Interrupt watchdog now registers tick hooks to both cores.
API for cross core tick and idle hook registration were also added
Do some refactor to socket ping:
1. Add ping_deinit to kill ping thread
2. Apply configuration set by esp_ping_set_target to socket ping
3. Limit only one ping thread
Some development boards do not have sufficient external pull-ups on
SD card pins. Most notably, if high level on GPIO13 is not registered
by the card when GO_IDLE_STATE command is received, the card will enter
SPI mode and further communication will not be possible, until power to
the card is toggled.
This change enables internal pull-ups on SD card pins in an attempt to
make this initialization process more reliable.
Previously the timeout was set to the same value (1000ms) for all kinds
of commands. In some cases, such as with slow cards, write commands
failed to complete in time.
This change makes command timeouts configurable via sdmmc_host_t
structure, and also makes default timeouts different for ordinary
commands and write commands.
Closes https://github.com/espressif/esp-idf/issues/1093
Ref TW15774.
Previously if multiple tasks had been added to xPendingReadyList for the CPU, only the first one was resumed.
Includes a test case for resuming multiple (pending) tasks on xTaskResumeAll().
Document the limitation that while scheduler is suspended on one CPU, it can't wake tasks on either CPU.
for me it was necessary to add the key manually to the key ring. Otherwise I could not have installed the packages
Merges https://github.com/espressif/esp-idf/pull/1029
(Amended to remove reference to exact key, references AUR links instead.)
The way these hooks are implemented at the moment, once you register a tick or idle task hook, it is run by both cores, leading to intermittent crashes that are difficult to explain (and debug). One solution is to register the hook with the core that is currently running, which is what this patch attempts to do.
Merges https://github.com/espressif/esp-idf/pull/781
using apll_param to setup APLL
new apll calculation method, much faster
validate freq calculation
Ensure that the i2s frequency is greater than the hardware limit
Add description of how to calculate apll clock, support apll for other 16-bits audio, check rev0 chip
correct space
* Only direct invocation of cypto_hash_sha256 & crypto_hash_sha512 produced correct output.
* Some remaining header file mixups, so changed approach to wrapping the state structures.
* Fixes https://github.com/espressif/esp-idf/issues/1044 (crypto_sign problems)
* Add option to disable mbedTLS implementation for SHA256 & SHA512 in libsodium
All options that were enabled via CONFIG_MDNS are now in menuconfig, with
the default values set the same as with CONFIG_MDNS enabled (meaning existing
projects that were using CONFIG_MDNS do not need to change).
* setsockopt(s, IPV6_ONLY, &one, sizeof(int)) will disable IPV6-only
mode. Incoming/outgoing IPV4 packets are dropped.
* Otherwise, sockets bound to IPV6_ANY_ADDR can receive unicast packets
for IPV4 or IPV6.
* sendto() a IPV6-mapped-IPV4 address on a UDP socket works correctly
(not supported for RAW or TCP sockets.)
* getaddrinfo() option AI_V4MAPPED is implemented.
As well as extending support to TCP & RAW, there is some potential improvement
to dropping incoming packets - the drop happens a bit late in the process and
there is no "ICMP port unreachable" response sent.
Legacy API of task watchdog used the same function esp_task_wdt_feed() to add
and feed a task. This caused issues of implicitly adding a task to the wdt list
if the function was used in shared code.
The new API introduces init, adding, feeding, deleting, deinit functions. Tasks
must now be explicitly added to the task watchdog using their handles. Deletion
must also be explicit using task handles. This resolves the issue of implicit
task additions to the task watchdog due to shared code calling
esp_task_wdt_feed().
Task watchdog is now fully configurable at runtime by calling the init and
deinit functions.
Also added functions to get the handles of idle tasks of the other core. This
helps when adding idle tasks to the watchdog at run time.
Configuring the task watchdog using menu config is still available, however
menu config will only result in calling the init and add functions for idle
tasks shortly after the scheduler starts.
Menu config also allows for using legacy behavior, however the legacy behavior
willcall the new API functions but with slight variations to make them legacy
compatible.
Documentation and example have also been updated
gcov_rtio.c headers updated to prevent error of freertos header files being
included in the wrong order.
Resolves issue TW#13265
The two task watchdog timer bugs are as follows...
1) If only a single task existed on the wdt task list, and esp_task_wdt_feed()
was only called once, the watchdog triggers but fails to print task name
2) If a single task already exists on the task wdt list, and another task calls
esp_task_wdt_feed() once, the watchdog fails to trigger
Problem stemmed from the loop responsible for resetting the watchdog timer
having incorrect loop parameters. The loop failed to traverse the full length
of the task wdt list
In release mode, switches in rtc_clk_bbpll_set would be converted to
jump tables. These tables would be placed into .rodata, which caused
rtc_clk_cpu_freq_set to be unusable while cache is disabled. This
manifested itself in crashes when exiting from light sleep:
https://esp32.com/posting.php?mode=reply&f=13&t=3089#pr14590
get IP address after connecting to the softap.
Now the default netif is station in station+softap mode. The UDP pcb of
DHCP server is binded to IP 0.0.0.0. When other device connects to softap, the
DHCP offer will be sent by softap.But because the destination IP of DHCP offer
is broadcast IP and the source IP of it is 0.0.0.0, it will be sent from default
netif, that is station interface. Other device can not receive the DHCP offer
sent from station interface. As a result, other device can not get IP address.
The resolution is that bind UDP pcb to the IP address of softap. So, the source
IP of DHCP offer is that of softap. DHCP offer can be sent from softap interface
by source IP route method.
Added documentation about the ESP-IDF changes to FreeRTOS.
The documentation covers changes to the following FreeRTOS aspects.
- Task Creation
- Affects on scheduling (Task skipping, scheduler suspension, tick synchronicity)
- Critical sections and disabling interrupts
- Thread Local Storage Pointers and deletion callbacks
- Configuring ESP-IDF FreeRTOS
Previously suggested parser command pattern:
xtensa-esp32-elf-(g?cc)|([gc]\+\+)|(clang)
was incorrect for compilation of c++ files, as it is expanded by Eclipse into or between:
xtensa-esp32-elf-(g?cc)
([gc]\+\+)
(clang)
Additional grouping around existing pattern solves that issue, and helps Eclipse to correctly find ESP-IDF includes.
Merges https://github.com/espressif/esp-idf/pull/1005
Previously, nvs_flash_init_custom would not be called if Storage for a
particular partition was already created. This caused issues if the
first call to nvs_flash_init failed due to Storage init error. This issue
exhibited itself as random failures of NVS CI test.
With this change, storage object is deleted (and not added to storage
list) if initialization fails.
squash the commit.
component/bt:Added the update_white_list & set_prefer_conn_params API to the bt project.
component/bt: Added the get white list size API & delete the read adv tx power API.
component/bt: Change the esp_gap_ble_api.h esp_ble_gap_set_prefer_conn_params API docs.
changed btm_find_dev to btm_find_or_alloc_dev
component/bt: Change the rssi API deep copy method.
component/bt: Change the code as comment in the gitlab.
squash the commit.
component/bt:Added the update_white_list & set_prefer_conn_params API to the bt project.
component/bt: Added the get white list size API & delete the read adv tx power API.
component/bt: Change the esp_gap_ble_api.h esp_ble_gap_set_prefer_conn_params API docs.
changed btm_find_dev to btm_find_or_alloc_dev
component/bt: Change the rssi API deep copy method.
component/bt: Change the code as comment in the gitlab.
component/bt: change the ESP_BLE_CONN_PARAM_UNDEF redefinition error.
component/bt: Change the ESP_BLE_IS_VALID_PARAM function with the compile error.
New multi_heap code has proven effective at aborting when buffer overruns occur,
but it's currently hard to debug the stack traces from these failures.
- Separate Eddystone codes into the following 4 files:
esp_eddystone_protocol.h
esp_eddystone_api.h
esp_eddystone_api.c
edp_eddystone_demo.c
- Just store eddystone information into eddystone result
1. add adc2 coexistence
2. change NOW() to WDEV_NOW()
3. call ets_timer_done() before calling ets_timer_setfn()
4. fix the bug that api lock is not unlocked when call esp_wifi_stop()
twice
5. more hmac tx buffer limit from 32 to 64.
1. Support built-in ADC for I2S.
2. Modify code of ADC, made no change to the original APIs.
3. Add APIs in I2S:
esp_err_t i2s_set_adc_mode(adc_unit_t adc_unit, adc1_channel_t adc_channel);
4. Add I2S ADC/DAC example code.
5. add old-fashion definition to make it more compatible
6. replase spi_flash_ APIs with esp_partition_ APIs
7. add example of generating audio table from wav
8. change example sound
* Fixes issue in !1250 when IDF_PATH changes on build runner
* Allows checking document warnings before CI run
* Will be robust to line number changes in document files
Since 2.11.0, git does not default to 7 characters for short commit IDs,
instead automatically estimating the number of characters based on
repository size [1]. If the toolchain was compiled on a computer with
new version of git installed, commit ID will contain 8 characters, and
the check for the toolchain version will fail. As a workaround, trim the
commit ID to 7 characters when checking the version.
[1] e6c587c733
squash again all the commit.
component/bt: Change all the gattc API && bta gattc layer.
component/bt: Debug the code and change the btc_ble_gattc_get_db method.
component/bt: Change the gatt read API interface.
component/bt: Reconstruction the BTA_gattc_cache code.
component/bt: Change back the bluedroid_get_status to marco.
component/bt: Added the serch service res start_handle & end_handle to the result.
component/bt: Change the gattc docs format.
component/bt: Change the docs format.
component/bt: fix the read char value bug.
component/bt: change the gattc_get_attr_count method.
component/bt: Change back the bta_gattc write ccc code.
component/bt: Change the gattc api docs format
component/bt: Change the gattc API docs.
component/bt: Change the prepare write descriptor method to avoid the exection.
Component/bt: modify gatt clinet demo with new API
component/bt: Change the p_src_data->read.p_value to avoid exection.
compoent/bt: Change the bugfix of gattc unreg for the notify.
Modify gattc security demo
component/bt: Change the log error.
Component/bt: modify gattc_multi_connect demo
componnet/bt: Change the bta_gattc_cache sdp include.
component/bt: Change the start_handle & end_handle not from the service.
component/bt: Change the gattc API docs.
component/bt: Change the return issues.
component/bt: Fixed the include service bug.
component/bt: Modify gattc_multi_connect demo , add scan log
component/bt: Fixed the BTA_GATTC_GetIncludeService start handle & end handle error bug.
component/bt: Fix the invalid handle of the get all char issues.
component/bt: Fix the bug with get_db_size_with_type of the start handle & end_handle not correted issue.
component/bt: Fixed the get secondly service num not correct issue.
component/bt: Fixed the last service handle not correted issue.
1. Occupy conn[9] for adv. The max connection number of bluetooth controller decrease to 9. (Previously, it is 10)
2. modify the enum of setting BLE TX power corresponding to connection's.
3. fix libbtdm_app.a cwitch jump table
ESPNOW is a kind of WiFi communication bettween WiFi devices, no
matter they are connected to each other or not. Once two WiFi
devices are paired, they can send data to or receive data from
each other. The data is transmitted in action frame which can
be encrypted with CCMP method. ESPNOW also support mutilcast frame
transmitting.
When debugging crashes caused by flash cache access errors, OpenOCD may
request the value of uxTopUsedPriority when cache is disabled. Placing
it into IRAM to avoid an error in such case.
Since 9a8c0392, XTAL frequency is set to 40MHz by default, and users
of 26MHz boards need to select 26MHz manually. Most users are not aware
of this change, and existing getting started guides do not mention that
XTAL frequency needs to be set for some boards. So users are left with
garbage output from UART without any clue what to check.
This change adds a warning in case specific XTAL frequency was set, and
it does not match automatically detected one. This should help users
fix the issue.
1. Remove the bond_device global variable.
2. Fix bond_device add cause memory exception
3. Modify the code location.
4. modify thread security
5. remove esp_ble_clear_bond_device_list() API
6. modify esp_ble_get_gond_device_list() to return list immediately, rather than wait event.
7. modify the gatt_security_server demo to show how to remove all the bonded devices.
8. fix some code bugs may cause something error.
Fix warnings where undefined vars are used.
Make Kconfig emit "FOO=" for unset bool options
To ensure make variables are always defined, even if empty.
When writing auto.conf, include symbols disabled by dependency to make sure all make variables are always defined.
Fixesespressif/esp-idf#137
Cherry-picked from https://github.com/espressif/esp-idf/pull/138
Unlocking a never-locked mutex is an assertion failure in debug mode.
In release mode, this further improves performance:
No-Contention -> 153 cycles
Recursion No-Contention -> 138 cycles
Contention -> 378 cycles
Too hard to stage the dependencies so that all clean steps complete before any build steps begin. Also, using and then
deleting and then regenerating SDKCONFIG_MAKEFILE in one pass is really hard to manage successfully.
Regression introduced in 43e231c.
Thanks to @yanbe for pointing out issue in https://github.com/espressif/esp-idf/pull/955
This is a different fix, tries to keep the behaviour that 43e231c was aiming to correct (unnecessarily testing an
invalid slot more than once.)
Previously NVS did check CRC values of key-value pairs on the active
page, but the check for full pages was missing. This adds the necessary
check and a test for it.
Since timestamps are 64-bit, loosing one bit of range due to sign does
not present an issue, however for applications doing calculations on
timestamps, signed return type is more convenient.
The implementation of esp_timer_get_time used a critical section, which
resulted in a call time of ~1.8us. To make esp_timer_get_time more
useable as a high-resolution time source, this change replaces the lock
with polling. Call time is reduced to ~0.7us.
- update connection parameters timeout due to master update illegal connection parameters
- slave returns error status when slave check the connection parameters
- slave connection parameters update callback get that interval_max is equal to interval_min
Added component containg API that is able to correct raw ADC readings
into a voltage in mV. Also provided a helper function that combines
the process of getting the raw ADC1 reading then converting it to a
voltage in mV. In doing so, the adc1_get_voltage() function of the ADC
driver has been deprecated. Instead there is now adc1_get_raw to obtain
the raw ADC1 reading, and adc1_to_voltage() that gets the raw reading
and converts all in one function. Functions using the deprecated
adc1_get_voltage() have also been updated to use adc1_get_raw().
Conversion is based on ADC characteristics. The characteristics are based
on the ADC's v_ref, herefore the appropriate structure and functions have
been provided to obtain the ADC characteristics.
The existing ADC driver has also been modified by adding a function to
route the internal ADC reference voltage to a GPIO allowing users to measure
it manually.
Relevant documentation has also been updated
All peripheral clocks are default enabled after chip is powered on.
When CPU starts, if reset reason is CPU reset, disable those clocks
that are not enabled before reset. Otherwise, disable all those
useless clocks.
These peripheral clocks must be enabled when the peripherals are
initialized and disabled when they are deinitialized.
The code in xtensa_vectors.S did not handle XT_DEBUG_BACKTRACE
consistently: #if was used in one case, and #ifdef in another. This makes
the checks consistent, and also introduces a Kconfig option to enable
backtrace.
In some cases, xPortGetCoreID was not inlined, and ended up in flash.
Since this function is used in many situations when cache is disabled,
that caused exceptions. Adding IRAM attribute to fix that.
vfs_uart used same locks for read and write operations on a single UART.
If read operation was blocking (i.e. carried out via UART driver), the
lock was held by reading task until it received a line. During this time,
other tasks trying to write to the same UART would get blocked.
This change introduces separate read/write locks, and adds a test.
Another vfs_uart test if fixed (it was disabled since the
CONFIG_NEWLIB_STDOUT_ADDCR option was removed).
If two different types of SHA hashes were active in the hardware
concurrently, a race condition meant the SHA unit could be incorrectly
reset leading to all-zero results.
If scheduler switches cores in narrow window during esp_dport_access_stall_other_cpu_start(), could cause the stall
interrupt to occur on the running CPU - halting the CPU until WDT cleans up.
Related to https://github.com/espressif/esp-idf/issues/630
1. BIT(8) of CTRL is actually read-only bit indicating interrupt status
2. BIT(0) or CTRL had inverted meaning: 1 is “level”, 0 is “edge”
3. Add definitions of prescaler values
1. remove GKI(not use osi_free_and_reset)
2. modify mutex/semaphore to individual directory
3. set osi_malloc as malloc(previously use calloc)
4. change osi allocator debug osi_free
5. fix rebase of remove GKI
1. add sens_struct.h
2. add definition of RTCCNTL and RTCIO
3. modify touch pad examples
4. update example code.
5. add comments add option in menuconfig
6. fix issue that pad index 8 and 9 are mismatched
7. add touch_pad_read_filtered() api to get value filtered by iir filter
8. modify touch pad isr func
9. Make the items in perihperal.ld in the sequence of address
10. delete Kconfig for touch pad
11. add touchpad filter APIs to adjust the filter
12. add touch_pad into index.rst
13. add touch_pad in Doxyfile
14. add touch_pad.rst
- the first characteristic is used to receive data from client.
- the second characteristic is used to notify data to client.
- the third characteristic is used to receive command from client, user
can add code to process the command.
- the fourth characteristic is used to notify status to client.
- the fifth characteristic is used to keep ble connection
This commit adds support for multiple NVS partitions. This provides application a flexibility to have multiple NVS
partitions such as separate partition with read-only manufacturing data and read-write partition with configuration.
Application can also use this to separate out application's configuration storage from system configuration.
This feature does not change any of the basic property of NVS subsystem. The same-named namespaces across partitions are
considered to be different namespaces. The original NVS API available for the applications remains unchanged. The only
difference is that instead of first NVS partition in the partition table, it now operates on the partition with label
"nvs" (which is default in the IDF provided partition table files). Additional APIs are provided to open a handle and
erase NVS with partition name as a parameter.
A test case is added in the host tests and it is made sure that all the host tests pass. nvs_rw_value app is also tested
with multiple partitions.
Signed-off-by: Amey Inamdar <amey.inamdar@gmail.com>
This adds a simple script which parses Kconfig files using Kconfiglib
and emits ReST document with the list of all options. For each option
a link target is generated, to make it possible to link to any Kconfig
option from the rest of the documentation.
Since Kconfiglib is not on PyPI, the latest version (45f87b9d) is
bundled into the docs directory.
- The two most significant bits of the address shall be equal to 1
- All bits of the random part of the address shall not be equal to 1
- All bits of the random part of the address shall not be equal to 0
We had already updated to v1.24 months ago, but the submodule commit was accidentally
reverted in 1fb85b494c.
Fixes (again) error when compiling with assertions disabled.
As reported on forum: https://esp32.com/viewtopic.php?f=13&t=2750&p=13069
component/bt: cherry-pick the bugfix/btdm_api_manage_pair_info_#13119 to this branch.
component/bt: Change the ble gap API code format & added the status judgment in the btc_storage_load_bonded_ble_devices function.
Other terminal emulators (screen, minicom) default to sending CR when
ENTER is pressed on the keyboard. Make behavior of idf_monitor
consistent with them.
Between 3.1.0 and 3.3.0, pyserial had thread cancellation implemented
using a select, which blocked on the stdin and an auxiliary pipe. When
thread had to be cancelled, a byte would be sent into the pipe,
unblocking stdin.
Unfortunately, this method suffers from a problem with using select on
a StreamReader (which represents the decoder wrapped around stdin).
In some cases, when the TTY sends an escape sequence in response to
an escape sequence received from serial, this escape sequence will not
be read from stdin until some key is pressed.
In https://github.com/pyserial/pyserial/commit/cab3dab, this method
was replaced with an TIOCSTI ioctl. This change makes sure we use the
new cancellation method even if the script is running with older
pyserial.
Previously VFS driver for UART could only use simple non-blocking
functions to read from and write to the UART. UART driver provides more
complex blocking and interrupt-driven functions, which can be used
instead.
This commit adds optional support for using UART driver's functions.
Also added is a more flexible mechanism for configuring newline
conversion rules on input and output.
This commit also fixes a bug that all UARTs shared one static variable
used as a character buffer in newline conversion code. This variable is
changed to be per-UART.
* Disables 3DES, Camellia, Blowfish, RC4, RIPEMD160, SSLv3, TLS-PSK modes, DTLS by default
* Saves about 40KB from the default TLS client code size
* Defaults no longer get "Bad" howsmyssl.com rating (no more vulnerable 3DES)
(ping https://github.com/espressif/arduino-esp32/issues/575 )
* Allows up to another 20-30KB code size to be trimmed without security
implications if using DER formatted certificates, RSA ciphersuites only,
etc.
* Can save up to another 8KB by setting the TLS Role to Server or Client only.
1. Hello World application shows no footprint difference before and
after this change
2. examples/ethernet/ethernet application compiles properly (can't
test with my board)
By default SD cards are initialized in default speed (DS) mode. Enabling
HS mode requires SWITCH_FUNC command to be sent twice: first time to
query if the card supports switching to HS mode, second time to perform
the switch.
This change implements SWITCH_FUNC command and adds the procedure to
switch to HS mode.
In some cases the card needs to be returned to standby mode from data
transfer mode. This is done using CMD7 command, which does not receive
any response in this case.
‘make_hw_cmd’ function checks opcodes in a few cases. Comparing opcode
does not tell the whole story, because for some SD commands there is are
APP commands with the same opcodes. This change introduces a flag which
indicates whether the next command is going to be an APP command.
The check for APP_SET_BUS_WIDTH command is updated to use this flag.
This fixes a bug with an unexpected STOP_TRANSMISSION command sent after
SWITCH_FUNC command, which has opcode 6, same as APP_SET_BUS_WIDTH.
MMC_RSP_BITS helper function had a hack that it flipped word order in
the response, assuming that response size is 4 words. This hack does not
work for responses which are not 4 words long (such as the SWITCH_FUNC
response, which is 64 words long).
This change removes the hack and the matching word order reversal code
in sdmmc driver.
Remove wifi config option
Remove Wi-Fi enable/disable option from Kconfig. This can be detected by the presence of esp_wifi_init() function in the application. Minimum footprint impact after the change.
See merge request !1098
This is no longer required since the functions automatically get
pulled in based on the usage. A quick summary of footprint
comparisions before and after these set of patches is shown below:
Hello-World: (simplified for readability)
old Total image size:~ 104902 bytes (.bin may be padded larger)
old Total image size:~ 105254 bytes (.bin may be padded larger)
Per-archive contributions to ELF file:
Archive File DRAM .data & .bss IRAM Flash code & rodata Total
old libesp32.a 1973 177 4445 3939 2267 12801
new libesp32.a 1973 185 4473 3939 2267 12837
new libnvs_flash.a 0 92 0 274 8 374
new libstdc++.a 0 0 0 24 0 24
For some reason, nvs_flash.a (~400bytes) gets pulled in (particularly
the nvs_flash_init() function).
Power-Save: (simplified for readability)
old Total image size:~ 421347 bytes (.bin may be padded larger)
old Total image size:~ 421235 bytes (.bin may be padded larger)
old libtcpip_adapter.a 0 81 0 1947 115 2143
new libtcpip_adapter.a 0 69 0 1897 115 2081
The size actually shrinks a bit, since the AP interface function
doesn't get pulled in.
Since only the used interface's start function gets called, it pulls
in only the functions that are required in the current application,
thereby saving footprint.
Restart being a lower-layer system-level function, needn't depend on
the higher level Wi-Fi libraries.
This also enables us to get rid of one more WIFI_ENABLED ifdef check
1. Rename api from rmt_get_ringbuf_handler to rmt_get_ringbuf_handle (Github Issue #274)
2. doxygen param rename
3. change API rmt_wait_tx_done to specify maximum waiting time
4.Change return type of rmt_wait_tx_done API from bool to esp_err_t
5. update doc
The address field should be placed at the highest bits of address and slv_wr_status registers. Instead of breaking the address into two parts and fill in each register, move the address to the highest bits and write to the registers respectively.
Breaking change: if you fill-in the SPI address filed in a previous version in some way and it works correctly, you still have to rewrite the address, in a more intuitive way.
force rxlength=length and mosi=1 and inlink.start=1 on in full-duplex mode.
set rxlength > length is forbidden in full-duplex mode.
TW#12609, TW#14240, https://www.esp32.com/viewtopic.php?f=13&t=2519
SDMMC hardware treats all buffers as aligned, and ignores 2 LSBs of
addresses written into DMA descriptors. Previously SDMMC host driver
assumed that data buffers passed from SDDMC command layer would be
aligned. However alignment checks were never implemented in the command
layer, as were the checks that the buffer coming from the application
would be in DMA capable memory. Most of the time this was indeed true.
However in some cases FATFS library can pass buffers offset by 2 bytes
from word boundary. “DMA capable” restriction may be broken if pSRAM
support is used.
This change adds buffer checks to the SDMMC host driver (alignment and
DMA capability), so that the host layer will error out for incompatible
buffers. In SDMMC command layer, a check is added to read and write
functions. If an incompatible buffer is passed from the application, new
buffer (512 bytes size) is allocated, and the transfer is performed
using {READ,WRITE}_SINGLE_BLOCK commands.
Optimize TCP close:
1. Not remove TCP pcb when IP address is changed since the lwip netconn still need the pcb
2. If the TCP connection is in TCP_FIN_WAIT_1 for too long time, remove it
SD SPI mode driver
This MR adds functionality to support SD cards connected via SPI interface.
Additionally, two bugs are fixed:
- Definition of `SPI_TRANS_MODE_DIOQIO_ADDR` in spi_master driver
- SD card probing frequency was 4000kHz instead of 400kHz as required by the standard
See merge request !727
Make the list of examples permanent between jobs
because the results of the 'find' command are not sorted by name.
Fix the identified problem on master
See merge request !1036
gpio_matrix_out function will set output enable for GPIO, seems in gpio_matrix_out there will be a short moment that the chip will output GPIO level.
So we can set GPIO as high before gpio_matrix_out function.
Makes app image booting more reliable (256-bit rather than 8-bit verification.)
Some measurements, time to boot a 655KB app.bin file and run to app_main() execution.
(All for rev 1 silicon, ie no 340ms spurious WDT delay.)
80MHz QIO mode:
before = 300ms
after = 140ms
40MHz DIO mode:
before = 712ms
after = 577ms
40MHz DIO mode, secure boot enabled
before = 1380ms
after = 934ms
(Secure boot involves two ECC signature verifications (partition table, app) that take approx 300ms each with 80MHz CPU.)
For config-only components, component.mk should now contain "COMPONENT_CONFIG_ONLY := 1"
Also refactored some of the generation of linker paths, library list. This required cleaning up the way the bootloader
project works, it's now mostly independent from the parent.
Each COMPONENT_DIRS directory can now either be a component directory, or a parent directory containing component
subdirectories.
When searching for components, skip any directory which doesn't have component.mk, Kconfig.projbuild, or
Makefile.projbuild in it. This helps with debugging, list-components output, etc.
1. add ble tx power functions
2. add more osi functions.
3. modify bluetooth controller task procedure
4. fix a memory leak when controller deinit
5. add controller disable return value.
NVS is used to store PHY calibration data, WiFi configuration, and BT
configuration. Previously BT examples did not call nvs_flash_init,
relying on the fact that it is called during PHY init. However PHY init
did not handle possible NVS initialization errors.
This change moves PHY init procedure into the application, and adds
diagnostic messages to BT config management routines if NVS is not
initialized.
In ecp_mul_comb(), if (!p_eq_g && grp->T == NULL) and ecp_precompute_comb() fails (which can happen due to OOM), then the new array of points T was leaked.
Currently the last 128KB of DRAM is reserved for the bootloader & early boot stacks. This means if >192KB of static DRAM
is allocated, the only available heap is this region - which is disabled until the scheduler starts. As a result, you
get either heap corruption on early boot if the static data overlaps startup heap (leading to very weird errors), or
FreeRTOS will fail to start when it can't malloc() anything.
Long term fix is to move the stacks & bootloader data to the very end of RAM, and only reserve that part for early
boot. This is a little fiddly because of also wanting to make sure this memory is not preemptively fragmented when it
gets reintroduced to the heap. This will become more important if/when we have more static allocation options in the
future.
For now, these errors make it clear why the boot has failed.
Ref TW13909
Because of errata related to BOD reset function, brownout is handled as follows:
- attach an ISR to brownout interrupt
- when ISR happens, print a message and do a software restart
- esp_restart_nonos enables RTC watchdog, so if restart fails,
there will be one more attempt to restart (using the RTC
watchdog)
RTC watchdog didn’t have any actions configured for any of the stages.
This change configures it to use SW_SYSTEM_RESET at stage 0 and a
full reset at stage 1. The timeout is now calculated based on
RTC_SLOW_CLK frequency.
unused variable 'lfn'
'isr_handler' defined but not used
'servo_set_angle' defined but not used
'gpio_test_signal' defined but not used
'change_duty' defined but not used
Now the tests do not pass
Before we had incorrect code of the error code checking
in build_examples.sh for that case and did nothing in test_build_system.sh.
component/bt: Fixed the bug crash of disconnet BLE when close the SMP module in the menuconfig.
component/bt: Removed the Excess #endid ///SMP_INCLUDED == TRUE in the l2cu_no_dynamic_ccbs function.
If destination IP address of the packet is broadcast address, firstly compare
source IP address with the that of each network interface. If it matches,
packet is forwarded from the interface.
The CI uses the mirror-submodule-update.sh for non-permanent reassignment
of 3rdparty sub-modules to local mirrors (only for 'non-master' branches).
List of the mirrors in mirror-list.txt
You can use the script locally to speed up data retrieval on network problems
check_submodule_sync job uses 'GIT_STRATEGY: clone' to check the availability of public sources
If scheduler was running, and lock was an automatic variable (ie stack-allocated) to be initialised by _lock_init*,
initialisation could be skipped if the lock variable was non-zero (and lock would be left invalid).
In other cases the lock is statically initialised to zero by __LOCK_INIT*
Specifying -fexceptions for the compiler is not enough.
- add necessary zero padding after .eh_frame section
- link .gcc_except_table_table in a way flash script does not complain
- call __registrer_frame_info before global constructors
Kudos jcmvbkbc for the necessary help.
Implements support for system level traces compatible with SEGGER
SystemView tool on top of ESP32 application tracing module.
That kind of traces can help to analyse program's behaviour.
SystemView can show timeline of tasks/ISRs execution, context switches,
statistics related to the CPUs' load distribution etc.
Also this commit adds useful feature to ESP32 application tracing module:
- Trace data buffering is implemented to handle temporary peaks of events load
Fixes issue with GPIO 0 being enabled as an output on ESP32D2WD (or when setting SPI pins in efuse)
and not using Quad-I/O modes.
Ref: https://esp32.com/viewtopic.php?f=2&t=2205
Add new "make size_components" and "make size_files" targets for analysing makeup of the ELF file.
Plain "make size" output now looks like this:
Total sizes:
DRAM .data size: 11156 bytes
DRAM .bss size: 22304 bytes
Used static DRAM: 33460 bytes ( 294220 available, 10.2% used)
Used static IRAM: 80480 bytes ( 50592 available, 61.4% used)
Flash code: 421463 bytes
Flash rodata: 103824 bytes
Total image size:~ 616923 bytes (.bin may be padded larger)
* [Getting Started Guide for the stable ESP-IDF version](https://docs.espressif.com/projects/esp-idf/en/stable/get-started/)
* [Getting Started Guide for the latest (master branch) ESP-IDF version](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/)
## Finding a Project
As well as the [esp-idf-template](https://github.com/espressif/esp-idf-template) project mentioned in the setup guide, ESP-IDF comes with some example projects in the [examples](examples) directory.
As well as the [esp-idf-template](https://github.com/espressif/esp-idf-template) project mentioned in Getting Started, ESP-IDF comes with some example projects in the [examples](examples) directory.
Once you've found the project you want to work with, change to its directory and you can configure and build it.
To start your own project based on an example, copy the example project directory outside of the ESP-IDF directory.
# Quick Reference
See the Getting Started guide links above for a detailed setup guide. This is a quick reference for common commands when working with ESP-IDF projects:
## Configuring the Project
`make menuconfig`
@@ -36,15 +41,17 @@ Once done configuring, press Escape multiple times to exit and say "Yes" to save
## Compiling the Project
`make all`
`make -j4 all`
... will compile app, bootloader and generate a partition table based on the config.
NOTE: The `-j4` option causes `make` to run 4 parallel jobs. This is much faster than the default single job. The recommended number to pass to this option is `-j(number of CPUs + 1)`.
## Flashing the Project
When `make all` finishes, it will print a command line to use esptool.py to flash the chip. However you can also do this from make by running:
When the build finishes, it will print a command line to use esptool.py to flash the chip. However you can also do this automatically by running:
`make flash`
`make -j4 flash`
This will flash the entire project (app, bootloader and partition table) to a new chip. The settings for serial port flashing can be configured with `make menuconfig`.
@@ -52,28 +59,28 @@ You don't need to run `make all` before running `make flash`, `make flash` will
## Viewing Serial Output
The `make monitor` target uses the [idf_monitor tool](http://esp-idf.readthedocs.io/en/latest/get-started/idf-monitor.html) to display serial output from the ESP32. idf_monitor also has a range of features to decode crash output and interact with the device. [Check the documentation page for details](http://esp-idf.readthedocs.io/en/latest/get-started/idf-monitor.html).
The `make monitor` target uses the [idf_monitor tool](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/idf-monitor.html) to display serial output from the ESP32. idf_monitor also has a range of features to decode crash output and interact with the device. [Check the documentation page for details](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/idf-monitor.html).
Exit the monitor by typing Ctrl-].
To flash and monitor output in one pass, you can run:
To build, flash and monitor output in one pass, you can run:
`make flash monitor`
`make -j4 flash monitor`
## Compiling & Flashing Just the App
## Compiling & Flashing Only the App
After the initial flash, you may just want to build and flash just your app, not the bootloader and partition table:
*`make app` - build just the app.
*`make app-flash` - flash just the app.
`make app-flash` will automatically rebuild the app if it needs it.
`make app-flash` will automatically rebuild the app if any source files have changed.
(In normal development there's no downside to reflashing the bootloader and partition table each time, if they haven't changed.)
## Parallel Builds
ESP-IDF supports compiling multiple files in parallel, so all of the above commands can be run as `make -jN` where `N` is the number of parallel make processes to run (generally N should be equal to or one more than the number of CPU cores in your system.)
ESP-IDF supports compiling multiple files in parallel, so all of the above commands can be run as `make -jN` where `N` is the number of parallel make processes to run (generally N should be equal to the number of CPU cores in your system, plus one.)
Multiple make functions can be combined into one. For example: to build the app & bootloader using 5 jobs in parallel, then flash everything, and then display serial output from the ESP32 run:
@@ -81,6 +88,7 @@ Multiple make functions can be combined into one. For example: to build the app
make -j5 flash monitor
```
## The Partition Table
Once you've compiled your project, the "build" directory will contain a binary file with a name like "my_app.bin". This is an ESP32 image binary that can be loaded by the bootloader.
@@ -96,7 +104,7 @@ The simplest way to use the partition table is to `make menuconfig` and choose o
In both cases the factory app is flashed at offset 0x10000. If you `make partition_table` then it will print a summary of the partition table.
For more details about partition tables and how to create custom variations, view the `docs/partition-tables.rst` file.
For more details about partition tables and how to create custom variations, view the [`docs/en/api-guides/partition-tables.rst`](docs/en/api-guides/partition-tables.rst) file.
## Erasing Flash
@@ -106,11 +114,12 @@ This can be combined with other targets, ie `make erase_flash flash` will erase
# Resources
* Documentation for the latest version: http://esp-idf.readthedocs.io/. This documentation is built from the [docs directory](docs) of this repository.
* Documentation for the latest version: https://docs.espressif.com/projects/esp-idf/. This documentation is built from the [docs directory](docs) of this repository.
* The [esp32.com forum](http://esp32.com/) is a place to ask questions and find community resources.
* The [esp32.com forum](https://esp32.com/) is a place to ask questions and find community resources.
* [Check the Issues section on github](https://github.com/espressif/esp-idf/issues) if you find a bug or have a feature request. Please check existing Issues before opening a new one.
* If you're interested in contributing to ESP-IDF, please check the [Contributions Guide](http://esp-idf.readthedocs.io/en/latest/contribute/index.html).
* If you're interested in contributing to ESP-IDF, please check the [Contributions Guide](https://docs.espressif.com/projects/esp-idf/en/latest/contribute/index.html).
#define SEGGER_SYSVIEW_ID_BASE 0x3F400000 // Default value for the lowest Id reported by the application. Can be overridden by the application via SEGGER_SYSVIEW_SetRAMBase(). (i.e. 0x20000000 when all Ids are an address in this RAM)
#define SEGGER_SYSVIEW_ID_SHIFT 0 // Number of bits to shift the Id to save bandwidth. (i.e. 2 when Ids are 4 byte aligned)
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() ((*(U32 *)(0xE000ED04)) & 0x1FF) // Get the currently active interrupt Id. (i.e. read Cortex-M ICSR[8:0] = active vector)
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() (__get_IPSR()) // Workaround for IAR, which might do a byte-access to 0xE000ED04. Read IPSR instead.
#else
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() ((*(U32 *)(0xE000ED04)) & 0x3F) // Get the currently active interrupt Id. (i.e. read Cortex-M ICSR[5:0] = active vector)
#endif
#else
#define SEGGER_SYSVIEW_GET_INTERRUPT_ID() SEGGER_SYSVIEW_X_GetInterruptId() // Get the currently active interrupt Id from the user-provided function.
// Description for a circular buffer (also called "ring buffer")
// which is used as up-buffer (T->H)
//
typedefstruct{
constchar*sName;// Optional name. Standard names so far are: "Terminal", "SysView", "J-Scope_t4i4"
char*pBuffer;// Pointer to start of buffer
unsignedSizeOfBuffer;// Buffer size in bytes. Note that one byte is lost, as this implementation does not fill up the buffer in order to avoid the problem of being unable to distinguish between full and empty.
unsignedWrOff;// Position of next item to be written by either target.
volatileunsignedRdOff;// Position of next item to be read by host. Must be volatile since it may be modified by host.
unsignedFlags;// Contains configuration flags
}SEGGER_RTT_BUFFER_UP;
//
// Description for a circular buffer (also called "ring buffer")
// which is used as down-buffer (H->T)
//
typedefstruct{
constchar*sName;// Optional name. Standard names so far are: "Terminal", "SysView", "J-Scope_t4i4"
char*pBuffer;// Pointer to start of buffer
unsignedSizeOfBuffer;// Buffer size in bytes. Note that one byte is lost, as this implementation does not fill up the buffer in order to avoid the problem of being unable to distinguish between full and empty.
volatileunsignedWrOff;// Position of next item to be written by host. Must be volatile since it may be modified by host.
unsignedRdOff;// Position of next item to be read by target (down-buffer).
unsignedFlags;// Contains configuration flags
}SEGGER_RTT_BUFFER_DOWN;
//
// RTT control block which describes the number of buffers available
// as well as the configuration for each buffer
//
//
typedefstruct{
characID[16];// Initialized to "SEGGER RTT"
intMaxNumUpBuffers;// Initialized to SEGGER_RTT_MAX_NUM_UP_BUFFERS (type. 2)
intMaxNumDownBuffers;// Initialized to SEGGER_RTT_MAX_NUM_DOWN_BUFFERS (type. 2)
SEGGER_RTT_BUFFER_UPaUp[SEGGER_RTT_MAX_NUM_UP_BUFFERS];// Up buffers, transferring information up from target via debug probe to host
SEGGER_RTT_BUFFER_DOWNaDown[SEGGER_RTT_MAX_NUM_DOWN_BUFFERS];// Down buffers, transferring information down from host via debug probe to target
#define SEGGER_SYSVIEW_INFO_SIZE 9 // Minimum size, which has to be reserved for a packet. 1-2 byte of message type, 0-2 byte of payload length, 1-5 bytes of timestamp.
#define SEGGER_SYSVIEW_QUANTA_U32 5 // Maximum number of bytes to encode a U32, should be reserved for each 32-bit value in a packet.
#define SEGGER_SYSVIEW_LOG (0u)
#define SEGGER_SYSVIEW_WARNING (1u)
#define SEGGER_SYSVIEW_ERROR (2u)
#define SEGGER_SYSVIEW_FLAG_APPEND (1u << 6)
#define SEGGER_SYSVIEW_PREPARE_PACKET(p) (p) + 4
//
// SystemView events. First 32 IDs from 0 .. 31 are reserved for these
* If esp_ota_set_boot_partition() has been called, the partition which was set by that function will be returned.
*
* If esp_ota_set_boot_partition() has not been called, the result is
* equivalent to esp_ota_get_running_partition().
* If esp_ota_set_boot_partition() has not been called, the result is usually the same as esp_ota_get_running_partition().
* The two results are not equal if the configured boot partition does not contain a valid app (meaning that the runningpartition
* will be an app that the bootloader chose via fallback).
*
* @return Pointer to info for partition structure, or NULL if no partition is found or flash read operation failed. Returned pointer is valid for the lifetime of the application.
* If the OTA data partition is not present or not valid then the result is the first app partition found in the
* partition table. In priority order, this means: the factory app, the first OTA app slot, or the test app partition.
*
* Note that there is no guarantee the returned partition is a valid app. Use esp_image_load(ESP_IMAGE_VERIFY, ...) to verify if the
* returned partition contains a bootable image.
*
* @return Pointer to info for partition structure, or NULL if partition table is invalid or a flash read operation failed. Any returned pointer is valid for the lifetime of the application.
* esp_ota_set_boot_partition(). Only the app whose code is currently
* running will have its partition information returned.
*
* The partition returned by this function may also differ from esp_ota_get_boot_partition() if the configured boot
* partition is somehow invalid, and the bootloader fell back to a different app partition at boot.
*
* @return Pointer to info for partition structure, or NULL if no partition is found or flash read operation failed. Returned pointer is valid for the lifetime of the application.
int "Maximum topic length (not including Thing Name)"
depends on AWS_IOT_SDK
default 60
range 10 1000
help
All shadow actions have to be published or subscribed to a topic which is of the format $aws/things/{thingName}/shadow/update/accepted. This refers to the size of the topic without the Thing Name
#define AWS_IOT_MY_THING_NAME "ESP32" ///< Thing Name of the Shadow this device is associated with
// MQTT PubSub
#define AWS_IOT_MQTT_TX_BUF_LEN 512///< Any time a message is sent out through the MQTT layer. The message is copied into this buffer anytime a publish is done. This will also be used in the case of Thing Shadow
#define AWS_IOT_MQTT_RX_BUF_LEN 512///< Any message that comes into the device should be less than this buffer size. If a received message is bigger than this buffer size the message will be dropped.
#define AWS_IOT_MQTT_NUM_SUBSCRIBE_HANDLERS 5///< Maximum number of topic filters the MQTT client can handle at any given time. This should be increased appropriately when using Thing Shadow
#define AWS_IOT_MQTT_TX_BUF_LEN CONFIG_AWS_IOT_MQTT_TX_BUF_LEN///< Any time a message is sent out through the MQTT layer. The message is copied into this buffer anytime a publish is done. This will also be used in the case of Thing Shadow
#define AWS_IOT_MQTT_RX_BUF_LEN CONFIG_AWS_IOT_MQTT_RX_BUF_LEN///< Any message that comes into the device should be less than this buffer size. If a received message is bigger than this buffer size the message will be dropped.
#define AWS_IOT_MQTT_NUM_SUBSCRIBE_HANDLERS CONFIG_AWS_IOT_MQTT_NUM_SUBSCRIBE_HANDLERS///< Maximum number of topic filters the MQTT client can handle at any given time. This should be increased appropriately when using Thing Shadow
// Thing Shadow specific configs
#define SHADOW_MAX_SIZE_OF_RX_BUFFER (AWS_IOT_MQTT_RX_BUF_LEN + 1) ///< Maximum size of the SHADOW buffer to store the received Shadow message
#define SHADOW_MAX_SIZE_OF_RX_BUFFER CONFIG_AWS_IOT_SHADOW_MAX_SIZE_OF_RX_BUFFER ///< Maximum size of the SHADOW buffer to store the received Shadow message, including NULL terminating byte
#define MAX_SIZE_OF_UNIQUE_CLIENT_ID_BYTES 80 ///< Maximum size of the Unique Client Id. For More info on the Client Id refer \ref response "Acknowledgments"
#define MAX_SIZE_CLIENT_ID_WITH_SEQUENCE (MAX_SIZE_OF_UNIQUE_CLIENT_ID_BYTES + 10) ///< This is size of the extra sequence number that will be appended to the Unique client Id
#define MAX_SIZE_CLIENT_TOKEN_CLIENT_SEQUENCE (MAX_SIZE_CLIENT_ID_WITH_SEQUENCE + 20) ///< This is size of the the total clientToken key and value pair in the JSON
#define MAX_ACKS_TO_COMEIN_AT_ANY_GIVEN_TIME 10///< At Any given time we will wait for this many responses. This will correlate to the rate at which the shadow actions are requested
#define MAX_THINGNAME_HANDLED_AT_ANY_GIVEN_TIME 10///< We could perform shadow action on any thing Name and this is maximum Thing Names we can act on at any given time
#define MAX_JSON_TOKEN_EXPECTED 120///< These are the max tokens that is expected to be in the Shadow JSON document. Include the metadata that gets published
#define MAX_SHADOW_TOPIC_LENGTH_WITHOUT_THINGNAME 60///< All shadow actions have to be published or subscribed to a topic which is of the formablogt $aws/things/{thingName}/shadow/update/accepted. This refers to the size of the topic without the Thing Name
#define MAX_SIZE_OF_THING_NAME 20///< The Thing Name should not be bigger than this value. Modify this if the Thing Name needs to be bigger
#define MAX_ACKS_TO_COMEIN_AT_ANY_GIVEN_TIME CONFIG_AWS_IOT_SHADOW_MAX_SIMULTANEOUS_ACKS///< At Any given time we will wait for this many responses. This will correlate to the rate at which the shadow actions are requested
#define MAX_THINGNAME_HANDLED_AT_ANY_GIVEN_TIME CONFIG_AWS_IOT_SHADOW_MAX_SIMULTANEOUS_THINGNAMES///< We could perform shadow action on any thing Name and this is maximum Thing Names we can act on at any given time
#define MAX_JSON_TOKEN_EXPECTED CONFIG_AWS_IOT_SHADOW_MAX_JSON_TOKEN_EXPECTED///< These are the max tokens that is expected to be in the Shadow JSON document. Include the metadata that gets published
#define MAX_SHADOW_TOPIC_LENGTH_WITHOUT_THINGNAME CONFIG_AWS_IOT_SHADOW_MAX_SHADOW_TOPIC_LENGTH_WITHOUT_THINGNAME///< All shadow actions have to be published or subscribed to a topic which is of the formablogt $aws/things/{thingName}/shadow/update/accepted. This refers to the size of the topic without the Thing Name
#define MAX_SIZE_OF_THING_NAME CONFIG_AWS_IOT_SHADOW_MAX_SIZE_OF_THING_NAME///< The Thing Name should not be bigger than this value. Modify this if the Thing Name needs to be bigger
#define MAX_SHADOW_TOPIC_LENGTH_BYTES (MAX_SHADOW_TOPIC_LENGTH_WITHOUT_THINGNAME + MAX_SIZE_OF_THING_NAME) ///< This size includes the length of topic with Thing Name
// Auto Reconnect specific config
#define AWS_IOT_MQTT_MIN_RECONNECT_WAIT_INTERVAL 1000///< Minimum time before the First reconnect attempt is made as part of the exponential back-off algorithm
#define AWS_IOT_MQTT_MAX_RECONNECT_WAIT_INTERVAL 128000///< Maximum time interval after which exponential back-off will stop attempting to reconnect.
#define AWS_IOT_MQTT_MIN_RECONNECT_WAIT_INTERVAL CONFIG_AWS_IOT_MQTT_MIN_RECONNECT_WAIT_INTERVAL///< Minimum time before the First reconnect attempt is made as part of the exponential back-off algorithm
#define AWS_IOT_MQTT_MAX_RECONNECT_WAIT_INTERVAL CONFIG_AWS_IOT_MQTT_MAX_RECONNECT_WAIT_INTERVAL///< Maximum time interval after which exponential back-off will stop attempting to reconnect.
int "SPI Flash WP Pin when customising pins via efuse (read help)"
range 0 33
default 7
depends on FLASHMODE_QIO || FLASHMODE_QOUT
help
This value is ignored unless flash mode is set to QIO or QOUT *and* the SPI flash pins have been
overriden by setting the efuses SPI_PAD_CONFIG_xxx.
When this is the case, the Efuse config only defines 3 of the 4 Quad I/O data pins. The WP pin (aka ESP32
pin "SD_DATA_3" or SPI flash pin "IO2") is not specified in Efuse. That pin number is compiled into the bootloader
instead.
The default value (GPIO 7) is correct for WP pin on ESP32-D2WD integrated flash.
choice BOOTLOADER_VDDSDIO_BOOST
bool "VDDSDIO LDO voltage"
default BOOTLOADER_VDDSDIO_BOOST_1_9V
help
If this option is enabled, and VDDSDIO LDO is set to 1.8V (using EFUSE
or MTDI bootstrapping pin), bootloader will change LDO settings to
output 1.9V instead. This helps prevent flash chip from browning out
during flash programming operations.
This option has no effect if VDDSDIO is set to 3.3V, or if the internal
VDDSDIO regulator is disabled via efuse.
config BOOTLOADER_VDDSDIO_BOOST_1_8V
bool "1.8V"
depends on !ESPTOOLPY_FLASHFREQ_80M
config BOOTLOADER_VDDSDIO_BOOST_1_9V
bool "1.9V"
endchoice
config BOOTLOADER_FACTORY_RESET
bool "GPIO triggers factory reset"
default N
help
Allows to reset the device to factory settings:
- clear one or more data partitions;
- boot from "factory" partition.
The factory reset will occur if there is a GPIO input pulled low while device starts up.
See settings below.
config BOOTLOADER_NUM_PIN_FACTORY_RESET
int "Number of the GPIO input for factory reset"
depends on BOOTLOADER_FACTORY_RESET
range 0 39
default 4
help
The selected GPIO will be configured as an input with internal pull-up enabled.
To trigger a factory reset, this GPIO must be pulled low on reset.
Note that GPIO34-39 do not have an internal pullup and an external one must be provided.
config BOOTLOADER_OTA_DATA_ERASE
bool "Clear OTA data on factory reset (select factory partition)"
depends on BOOTLOADER_FACTORY_RESET
help
The device will boot from "factory" partition (or OTA slot 0 if no factory partition is present) after a factory reset.
config BOOTLOADER_DATA_FACTORY_RESET
string "Comma-separated names of partitions to clear on factory reset"
depends on BOOTLOADER_FACTORY_RESET
default "nvs"
help
Allows customers to select which data partitions will be erased while factory reset.
Specify the names of partitions as a comma-delimited with optional spaces for readability. (Like this: "nvs, phy_init, ...")
Make sure that the name specified in the partition table and here are the same.
Partitions of type "app" cannot be specified here.
config BOOTLOADER_APP_TEST
bool "GPIO triggers boot from test app partition"
default N
help
Allows to run the test app from "TEST" partition.
A boot from "test" partition will occur if there is a GPIO input pulled low while device starts up.
See settings below.
config BOOTLOADER_NUM_PIN_APP_TEST
int "Number of the GPIO input to boot TEST partition"
depends on BOOTLOADER_APP_TEST
range 0 39
default 18
help
The selected GPIO will be configured as an input with internal pull-up enabled.
To trigger a test app, this GPIO must be pulled low on reset.
After the GPIO input is deactivated and the device reboots, the old application will boot.
(factory or OTA[x]).
Note that GPIO34-39 do not have an internal pullup and an external one must be provided.
config BOOTLOADER_HOLD_TIME_GPIO
int "Hold time of GPIO for reset/test mode (seconds)"
depends on BOOTLOADER_FACTORY_RESET || BOOTLOADER_APP_TEST
default 5
help
The GPIO must be held low continuously for this period of time after reset
before a factory reset or test partition boot (as applicable) is performed.
endmenu # Bootloader
menu "Security features"
# These three are the actual options to check in code,
# selected by the displayed options
config SECURE_SIGNED_ON_BOOT
bool
default y
depends on SECURE_BOOT_ENABLED || SECURE_SIGNED_ON_BOOT_NO_SECURE_BOOT
config SECURE_SIGNED_ON_UPDATE
bool
default y
depends on SECURE_BOOT_ENABLED || SECURE_SIGNED_ON_UPDATE_NO_SECURE_BOOT
config SECURE_SIGNED_APPS
bool
default y
depends on SECURE_SIGNED_ON_BOOT || SECURE_SIGNED_ON_UPDATE
config SECURE_SIGNED_APPS_NO_SECURE_BOOT
bool "Require signed app images"
default n
depends on !SECURE_BOOT_ENABLED
help
Require apps to be signed to verify their integrity.
This option uses the same app signature scheme as hardware secure boot, but unlike hardware secure boot it does not prevent the bootloader from being physically updated. This means that the device can be secured against remote network access, but not physical access. Compared to using hardware Secure Boot this option is much simpler to implement.
config SECURE_SIGNED_ON_BOOT_NO_SECURE_BOOT
bool "Bootloader verifies app signatures"
default n
depends on SECURE_SIGNED_APPS_NO_SECURE_BOOT
help
If this option is set, the bootloader will be compiled with code to verify that an app is signed before booting it.
If hardware secure boot is enabled, this option is always enabled and cannot be disabled.
If hardware secure boot is not enabled, this option doesn't add significant security by itself so most users will want to leave it disabled.
config SECURE_SIGNED_ON_UPDATE_NO_SECURE_BOOT
bool "Verify app signature on update"
default y
depends on SECURE_SIGNED_APPS_NO_SECURE_BOOT
help
If this option is set, any OTA updated apps will have the signature verified before being considered valid.
When enabled, the signature is automatically checked whenever the esp_ota_ops.h APIs are used for OTA updates,
or esp_image_format.h APIs are used to verify apps.
If hardware secure boot is enabled, this option is always enabled and cannot be disabled.
If hardware secure boot is not enabled, this option still adds significant security against network-based attackers by preventing spoofing of OTA updates.
config SECURE_BOOT_ENABLED
bool "Enable secure boot in bootloader (READ DOCS FIRST)"
default N
bool "Enable hardware secure boot in bootloader (READ DOCS FIRST)"
default n
help
Build a bootloader which enables secure boot on first boot.
@@ -44,7 +192,7 @@ config SECURE_BOOT_ENABLED
When enabling secure boot, JTAG and ROM BASIC Interpreter are permanently disabled by default.
Refer to http://esp-idf.readthedocs.io/en/latest/security/secure-boot.html before enabling.
Refer to https://docs.espressif.com/projects/esp-idf/en/latest/security/secure-boot.html before enabling.
choice SECURE_BOOTLOADER_MODE
bool "Secure bootloader mode"
@@ -71,12 +219,12 @@ endchoice
config SECURE_BOOT_BUILD_SIGNED_BINARIES
bool "Sign binaries during build"
depends on SECURE_BOOT_ENABLED
depends on SECURE_SIGNED_APPS
default y
help
Once secure boot is enabled, bootloader will only boot if partition table and app image are signed.
Once secure boot or signed app requirement is enabled, app images are required to be signed.
If enabled, these binary files are signed as part of the build process. The file named in "Secure boot private signing key" will be used to sign the image.
If enabled (default), these binary files are signed as part of the build process. The file named in "Secure boot private signing key" will be used to sign the image.
If disabled, unsigned app/partition data will be built. They must be signed manually using espsecure.py (for example, on a remote signing server.)
@@ -85,7 +233,7 @@ config SECURE_BOOT_SIGNING_KEY
depends on SECURE_BOOT_BUILD_SIGNED_BINARIES
default secure_boot_signing_key.pem
help
Path to the key file used to sign partition tables and app images for secure boot. Once secure boot is enabled, bootloader will only boot if partition table and app image are signed.
Path to the key file used to sign app images.
Key file is an ECDSA private key (NIST256p curve) in PEM format.
Note: After first boot, the system will be permanently encrypted. Re-flashing an encrypted
system is complicated and not always possible.
Read http://esp-idf.readthedocs.io/en/latest/security/flash-encryption.html before enabling.
Read https://docs.espressif.com/projects/esp-idf/en/latest/security/flash-encryption.html before enabling.
config FLASH_ENCRYPTION_INSECURE
bool "Allow potentially insecure options"
@@ -154,12 +323,17 @@ menu "Potentially insecure options"
config SECURE_BOOT_ALLOW_ROM_BASIC
bool "Leave ROM BASIC Interpreter available on reset"
depends on SECURE_BOOT_INSECURE
depends on SECURE_BOOT_INSECURE || FLASH_ENCRYPTION_INSECURE
default N
help
If not set (default), bootloader permanently disables ROM BASIC (on UART console) as a fallback if the bootloader image becomes invalid. This happens on first boot.
By default, the BASIC ROM Console starts on reset if no valid bootloader is
read from the flash.
Only set this option in testing environments.
When either flash encryption or secure boot are enabled, the default is to
disable this BASIC fallback mode permanently via efuse.
If this option is set, this efuse is not burned and the BASIC ROM Console may
remain accessible. Only set this option in testing environments.
bool "Allow app partition length not 64KB aligned"
depends on SECURE_BOOT_INSECURE
help
If not set (default), app partition size must be a multiple of 64KB. App images are padded to 64KB length, and the bootloader checks any trailing bytes after the signature (before the next 64KB boundary) have not been written. This is because flash cache maps entire 64KB pages into the address space. This prevents an attacker from appending unverified data after the app image in the flash, causing it to be mapped into the address space.
Setting this option allows the app partition length to be unaligned, and disables padding of the app image to this length. It is generally not recommended to set this option, unless you have a legacy partitioning scheme which doesn't support 64KB aligned partition lengths.
iram_seg (RWX) : org = 0x40080000, len = 0x400 /* 1k of IRAM used by bootloader functions which need to flush/enable APP CPU cache */
iram_pool_1_seg (RWX) : org = 0x40078000, len = 0x8000 /* IRAM POOL1, used for APP CPU cache. We can abuse it in bootloader because APP CPU is still held in reset, until we enable APP CPU cache */
dram_seg (RW) : org = 0x3FFF0000, len = 0x10000 /* 64k at the end of DRAM, after ROM bootloader stack */
The main purpose is to make sure the bootloader can load into main memory
without overwriting itself.
*/
MEMORY
{
/* I/O */
dport0_seg (RW) : org = 0x3FF00000, len = 0x10
/* IRAM POOL1, used for APP CPU cache. Bootloader runs from here during the final stage of loading the app because APP CPU is still held in reset, the main app enables APP CPU cache */
iram_loader_seg (RWX) : org = 0x40078000, len = 0x8000 /* 32KB, APP CPU cache */
* By default, if booting from flash fails the ESP32 will boot a
* BASIC console in ROM.
*
* Call this function (from bootloader or app) to permanently
* disable the console on this chip.
*/
voidesp_efuse_disable_basic_rom_console(void);
/* @brief Encode one or more sets of 6 byte sequences into
* 8 bytes suitable for 3/4 Coding Scheme.
*
* This function is only useful if the CODING_SCHEME efuse
* is set to value 1 for 3/4 Coding Scheme.
*
* @param[in] in_bytes Pointer to a sequence of bytes to encode for 3/4 Coding Scheme. Must have length in_bytes_len. After being written to hardware, these bytes will read back as little-endian words.
* @param[out] out_words Pointer to array of words suitable for writing to efuse write registers. Array must contain 2 words (8 bytes) for every 6 bytes in in_bytes_len. Can be a pointer to efuse write registers.
* @param in_bytes_len. Length of array pointed to by in_bytes, in bytes. Must be a multiple of 6.
*
* @return ESP_ERR_INVALID_ARG if either pointer is null or in_bytes_len is not a multiple of 6. ESP_OK otherwise.
* @brief Read the segment header and data offset of a segment in the image.
*
* If encryption is enabled, data will be transparently decrypted.
*
* @param index Index of the segment to load information for.
* @param src_addr Base address in flash of the image.
* @param[in] image_header Pointer to the flash image header, already loaded by @ref esp_image_load_header().
* @param log_errors Log errors reading the segment header.
* @param[out] segment_header Pointer to a segment header structure to be filled with data. If the function fails, contents are undefined.
* @param[out] segment_data_offset Pointer to the data offset of the segment.
*
* @return ESP_OK if segment_header & segment_data_offset were loaded successfully, ESP_ERR_IMAGE_FLASH_FAIL if a SPI flash error occurs, ESP_ERR_IMAGE_INVALID if the image header appears invalid, ESP_ERR_INVALID_ARG if the index is invalid.
* @brief Non-cryptographically validate app image integrity. On success, length of image is provided to caller.
*
* If the image has a secure boot signature appended, the signature is not checked and this length is not included in the
* output value.
* @param mode Mode of operation (verify, silent verify, or load).
* @param part Partition to load the app from.
* @param[inout] data Pointer to the image metadata structure which is be filled in by this function. 'start_addr' member should be set (to the start address of the image.) Other fields will all be initialised by this function.
*
* Image validation checks:
* - Magic byte
* - No single segment longer than 16MB
* - Total image no longer than 16MB
* - 8 bit image checksum is valid
*
* If flash encryption is enabled, the image will be tranpsarently decrypted.
*
* @param src_addr Offset of the start of the image in flash. Must be 4 byte aligned.
* @param allow_decrypt If true and flash encryption is enabled, the image will be transparently decrypted.
* @param log_errors Log errors verifying the image.
* @param[out] length Length of the image, set to a value if the image is valid. Can be null.
*
* @return ESP_OK if image is valid, ESP_FAIL or ESP_ERR_IMAGE_INVALID on errors.
* - Magic byte.
* - Partition smaller than 16MB.
* - All segments & image fit in partition.
* - 8 bit image checksum is valid.
* - SHA-256 of image is valid (if image has this appended).
* - (Signature) if signature verification is enabled.
*
* @return
* - ESP_OK if verify or load was successful
* - ESP_ERR_IMAGE_FLASH_FAIL if a SPI flash error occurs
* - ESP_ERR_IMAGE_INVALID if the image appears invalid.
* - ESP_ERR_INVALID_ARG if the partition or data pointers are invalid.
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
